 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DATA SHEET MOS INTEGRATED CIRCUIT PD17933, 17934 4-BIT SINGLE-CHIP MICROCONTROLLERS WITH DIGITAL TUNING SYSTEM HARDWARE The PD17933 and 17934 are 4-bit single-chip CMOS microcontrollers with hardware for digital tuning systems (DTSs). These microcontrollers integrate a prescaler that operates at a voltage as low as 1.05 V and up to 220 MHz, a PLL frequency synthesizer, an intermediate frequency (IF) counter, and an LCD controller/driver on a single chip. Therefore, a high-performance digital tuning system for a portable set can be organized with a single chip. FEATURES * Program memory (ROM) * Peripheral hardware General-purpose I/O ports, LCD controller/driver, serial interface, A/D converter, BEEP output, frequency counter * Interrupt External: 1 source Internal : 3 sources * Reset by RESET pin * Low power consumption * Supply voltage: VDD = 1.05 to 1.8 V PD17933 PD17934 448 x 4 bits * : 12K bytes (6144 x 16 bits) : 16K bytes (8192 x 16 bits) * General-purpose data memory (RAM) ) Instruction execution time 53.3 s (with 75-kHz crystal resonator) * PLL frequency synthesizer Dual modulus prescaler (220 MHz MAX.), programmable divider, phase comparator, charge pump ORDERING INFORMATION Part Number Package 80-pin plastic TQFP (12 x 12 mm, 0.5 mm pitch) 80-pin plastic TQFP (12 x 12 mm, 0.5 mm pitch) PD17933GK-xxx-BE9 PD17934GK-xxx-BE9 Remark xxx indicates ROM code suffix. Unless otherwise specified, the PD17934 is explained as the representative model in this document. The information in this document is subject to change without notice. Document No. U11947EJ2V0DS00 (2nd edition) Date Published July 1998 N CP(K) Printed in Japan The mark shows major revised points. (c) 1997 PD17933, 17934 FUNCTIONAL OUTLINE Part Number Program memory (ROM) General-purpose data memory (RAM) Instruction execution time General-purpose port 37 pins PD17933 12K bytes (6144 x 16 bits) 448 x 4 bits 53.3 s (with 75-MHz crystal oscillator) * I/O port * Input port PD17934 16K bytes (8192 x 16 bits) : 20 pins : 11 pins (of which 3 are muxed with LCD segment pins) * Output port : 6 pins Stack level * Address stack : 15 levels (stack can be manipulated) * Interrupt stack : 4 levels (stack can be manipulated) * External : 1 source (INT) * Internal : 3 sources (basic timer 0, 8-bit timer, serial interface) 3 * * * channels Basic timer 0 (125 ms) Basic timer 1 (8 ms, 32 ms) 8-bit timer (with event counter) Vector interrupt (maskable interrupt) Timer A/D converter LCD controller/driver 8-bits resolution x 3 channels * 20 segments, 4 commons * 1/4 duty, 1/2 bias, frame frequency: 62.5 Hz, drive voltage VLCD1=3.0 V TYP. * Muxed segment pins: 3 (Each can be used as general-purpose input port pin.) Serial interface PLL frequency synthesizer Division mode 1 channel (3-wire/2-wire modes selectable) 2 types * Direct division mode (VCOL pin) * Pulse swallow mode (VCOL pin/VCOH pin) Reference frequency Charge pump Phase comparator Intermediate frequency (IF) counter BEEP output Reset 6 types selectable (1, 3, 5, 6.25, 12.5, 25 kHz) Error out output: 2 pins (EO0 and EO1 pins) Unlock detectable by program Frequency measurement 1 pin (1.5 kHz, 3 kHz) * Reset by RESET pin * Watchdog timer reset Can be set only once on power application: 4096 or 8192 instructions selectable * Stack pointger overflow/underflow reset Can be set only once on power application: Interrupt stack and address stack selectable * AMIFC pin: 400 to 500 kHz * FMIFC pin: 10 to 11 MHz Supply voltage Package VDD = 1.05 to 1.8 V 80-pin plastic TQFP (12 x 12 mm, 0.5 mm pitch) 2 PD17933, 17934 PIN CONFIGURATION (Top View) 80-pin plastic TQFP (12 x 12 mm, 0.5 mm pitch) PD17933GK-xxx-BE9 PD17934GK-xxx-BE9 P2A2/LCD19 P2A1/LCD18 P2A0/LCD17 P0D3/AD2 P0D2/AD1 P0D1/AD0 P0D0 P2C3 P2C2 P2C1 P2C0 P0C3 P0C2 P0C1 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 P1C0/TM0 P1C1/TM1 P1C2/AMIFC P1C3/FMIFC/AMIFC VDD1 NC EO0 EO1 VCOL VCOH GND TEST RESET P2B0 P2B1 P2B2 P2B3 P0A0 P0A1 P1A0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 LCD16 LCD15 LCD14 LCD13 LCD12 LCD11 LCD10 LCD9 LCD8 LCD7 LCD6 LCD5 LCD4 LCD3 LCD2 LCD1 LCD0 COM3 COM2 COM1 P0B1/SI1/SO2 P0B2/SO1 P0B3/BEEP P1A1 P1A2 P1A3 P1D0 P1D1 P1D2 P1D3 P0B0/SCK VDD0 CAPLCD0 CAPLCD1 REGLCD0 REGLCD1 CAPLCD2 P0C0 GND VDD2 XOUT INT XIN CAPLCD3 REGLCD2 COM0 3 PD17933, 17934 PIN NAME AD0-AD2 AMIFC BEEP : A/D converter inputs : Intermediate frequency counter input for AM : BEEP output voltage COM0-COM3 EO0, EO1 FMIFC GND INT LCD0-LCD19 NC P0A0, P0A1 P0B0-P0B3 P0C0-P0C3 : LCD common output : Error output : Intermediate frequency counter input for FM : Ground : External interrupt input : LCD segment outputs : No connection : Port 0A : Port 0B : Port 0C CAPLCD0-CAPLCD3 : Capacitor connection for LCD drive P0D0-P0D3 P1A0-P1A3 P1C0-P1C3 P1D0-P1D3 P2A0-P2A2 P2B0-P2B3 P2C0-P2C3 RESET SCK SI1 SO1, SO2 TEST TM0, TM1 VCOH, VCOL VDD0-VDD2 XIN, XOUT : Port 0D : Port 1A : Port 1C : Port 1D : Port 2A : Port 2B : Port 2C : Reset input : 3-wire serial clock I/O : 3-wire serial data input : 3-wire serial data outputs : Test input : Timer event inputs : Local oscillation inputs for PLL : Power supply : Crystal resonator connection REGLCD0-REGLCD2: Regulator output for LCD drive 4 PD17933, 17934 BLOCK DIAGRAM P0A0, P0A1 P0B0-P0B3 P0C0-P0C3 P0D0-P0D3 P1A0-P1A3 P1C0-P1C3 P1D0-P1D3 P2A0-P2A2 P2B0-P2B3 P2C0-P2C3 2 4 4 RAM 448 x 4 bits BEEP SYSTEM REG. Port Interrupt controller ALU 8-bit timer Serial interface SCK/P0B0 SI1/SO2/P0B1 SO1/P0B2 4 4 BEEP/P0B3 4 4 INT TM0/P1C0 TM1/P1C1 3 4 4 Instruction decoder Basic timer0 REGLCD0 REGLCD2 CAPLCD0 CAPLCD3 Voltage doubler ROM PD17933 : 6144 x 16 bits PD17934 : 8192 x 16 bits Basic timer1 Frequency counter FMIFC/AMIFC/P1C3 AMIFC/P1C2 COM0 COM3 LCD0 LCD16 LCD17/P2A0 LCD19/P2A2 LCD controller/ driver Program counter PLL Stack 4 x 13 bits PLL voltage regulator A/D converter EO0 EO1 VCOL VCOH AD0/P0D1 AD1/P0D2 AD2/P0D3 VDD0-VDD2 Reset RESET GND XIN OSC OUT CPU Peripheral X 5 PD17933, 17934 CONTENTS 1. PIN FUNCTIONS ............................................................................................................................ 1.1 Pin Function List ................................................................................................................ 1.2 Equivalent Circuits of Pins ............................................................................................... 1.3 Recommended Connections of Unused Pins ................................................................ 1.4 Cautions on Using TEST Pin ............................................................................................ 2. PROGRAM MEMORY (ROM) ........................................................................................................ 2.1 Outline of Program Memory ............................................................................................. 2.2 Program Memory................................................................................................................ 2.3 Program Counter ............................................................................................................... 2.4 Flow of Program ................................................................................................................. 2.5 Cautions on Using Program Memory .............................................................................. 3. ADDRESS STACK (ASK) .............................................................................................................. 3.1 Outline of Address Stack .................................................................................................. 3.2 Address Stack Register (ASR) ......................................................................................... 3.3 Stack Pointer (SP) .............................................................................................................. 3.4 Operation of Address Stack ............................................................................................. 3.5 Cautions on Using Address Stack .................................................................................. 4. DATA MEMORY (RAM) ................................................................................................................. 4.1 Outline of Data Memory .................................................................................................... 4.2 Configuration and Function of Data Memory ................................................................ 4.3 Data Memory Addressing ................................................................................................. 4.4 Cautions on Using Data Memory ..................................................................................... 5. SYSTEM REGISTERS (SYSREG) ................................................................................................ 5.1 Outline of System Registers ............................................................................................ 5.2 System Register List ......................................................................................................... 5.3 Address Register (AR) ...................................................................................................... 5.4 Window Register (WR) ...................................................................................................... 5.5 Bank Register (BANK) ....................................................................................................... 5.6 Index Register (IX) and Data Memory Row Address Pointer (MP: memory pointer) ...................................................................................................... 5.7 General Register Pointer (RP) .......................................................................................... 5.8 Program Status Word (PSWORD) .................................................................................... 6. GENERAL REGISTER (GR) .......................................................................................................... 6.1 Outline of General Register .............................................................................................. 6.2 General Register ................................................................................................................ 6.3 Generating Address of General Register by Each Instruction ................................... 6.4 Cautions on Using General Register .............................................................................. 11 11 14 18 19 20 20 21 22 22 25 26 26 26 28 29 30 31 31 33 35 36 37 37 38 39 41 42 43 45 47 49 49 49 50 50 6 PD17933, 17934 7. ALU 7.1 7.2 7.3 7.4 (Arithmetic Logic Unit) BLOCK .......................................................................................... Outline of ALU Block ....................................................................................................... Configuration and Function of Each Block ................................................................... ALU Processing Instruction List ..................................................................................... Cautions on Using ALU .................................................................................................... 51 51 52 52 56 57 57 58 59 69 69 70 70 71 72 76 77 77 77 79 80 81 81 82 82 84 93 96 98 98 100 106 110 110 111 116 116 117 119 8. REGISTER FILE (RF) AND CONTROL REGISTERS ................................................................. 8.1 Outline of Register File ..................................................................................................... 8.2 Configuration and Function of Register File ................................................................. 8.3 Control Registers and Input/Output Selection Registers ............................................ 8.4 LCD Segment Registers .................................................................................................... 8.5 autions on Using Control Register ................................................................................. 9. DATA BUFFER (DBF) ................................................................................................................... 9.1 Outline of Data Buffer ....................................................................................................... 9.2 Data Buffer .......................................................................................................................... 9.3 Relationships between Peripheral Hardware and Data Buffer .................................... 9.4 Cautions on Using Data Buffer ........................................................................................ 10. DATA BUFFER STACK ................................................................................................................. 10.1 Outline of Data Buffer Stack ............................................................................................ 10.2 Data Buffer Stack Register ............................................................................................... 10.3 Data Buffer Stack Pointer ................................................................................................. 10.4 Operation of Data Buffer Stack ........................................................................................ 10.5 Using Data Buffer Stack ................................................................................................... 10.6 Cautions on Using Data Buffer Stack ............................................................................. 11. GENERAL-PURPOSE PORT ........................................................................................................ 11.1 Outline of General-purpose Port ..................................................................................... 11.2 General-Purpose I/O Port (P0B, P1A, P1D, P2B, P2C) ................................................. 11.3 General-Purpose Input Port (P0D, P1C, P2A) ................................................................ 11.4 General-Purpose Output Port (P0A, P0C) ...................................................................... 12. INTERRUPT ................................................................................................................................... 12.1 Outline of Interrupt Block ................................................................................................. 12.2 Interrupt Control Block ..................................................................................................... 12.3 Interrupt Stack Register .................................................................................................... 12.4 Stack Pointer, Address Stack Registers, and Program Counter ................................ 12.5 Interrupt Enable Flip-Flop (INTE) ..................................................................................... 12.6 Accepting Interrupt ............................................................................................................ 12.7 Operations after Interrupt Has Been Accepted ............................................................. 12.8 Returning from Interrupt Routine .................................................................................... 12.9 External Interrupts (INT pin) ............................................................................................. 12.10 Internal Interrupts .............................................................................................................. 7 PD17933, 17934 13. TIMERS ........................................................................................................................................... 13.1 Outline of Timers ............................................................................................................... 13.2 Basic Timer 0 ...................................................................................................................... 13.3 Basic Timer 1 ...................................................................................................................... 13.4 Timer 0 ................................................................................................................................. 14. A/D CONVERTER .......................................................................................................................... 14.1 Outline of A/D Converter .................................................................................................. 14.2 Input Selection Block ........................................................................................................ 14.3 Compare Voltage Generation and Compare Blocks ..................................................... 14.4 Comparison Timing Chart ................................................................................................ 14.5 Using A/D Converter .......................................................................................................... 14.6 Cautions on Using A/D Converter ................................................................................... 14.7 Status at Reset ................................................................................................................... 15. SERIAL INTERFACE ..................................................................................................................... 15.1 General ................................................................................................................................ 15.2 Clock Input/Output Control Block and Data Input/Output Control Block ................. 15.3 Clock Control Block .......................................................................................................... 15.4 Clock Counter ..................................................................................................................... 15.5 Presettable Shift Register ................................................................................................. 15.6 Wait Control Block ............................................................................................................. 15.7 Serial Interface Operation ................................................................................................. 15.8 Notes on Setting and Reading Data ................................................................................ 15.9 Operation Mode and Operational Outline of Each Blocks ........................................... 15.10 Status on Reset .................................................................................................................. 16. PLL FREQUENCY SYNTHESIZER ............................................................................................... 16.1 Outline of PLL Frequency Synthesizer ........................................................................... 16.2 Input Selection Block and Programmable Divider ........................................................ 16.3 Reference Frequency Generator ..................................................................................... 16.4 Phase Comparator (f-DET), Charge Pump, and Unlock FF ......................................... 16.5 PLL Disabled Status .......................................................................................................... 16.6 Using PLL Frequency Synthesizer .................................................................................. 16.7 Status at Reset ................................................................................................................... 17. INTERMEDIATE FREQUENCY (IF) COUNTER ........................................................................... 17.1 Outline of Frequency Counter ......................................................................................... 17.2 IF Counter Input Selection Block and Gate Time Control Block ................................ 17.3 Start/Stop Control Block and IF Counter ....................................................................... 17.4 Using IF Counter ................................................................................................................ 17.5 Status at Reset ................................................................................................................... 18. BEEP ............................................................................................................................................... 18.1 Outlines of BEEP ............................................................................................................... 18.2 Output Wave Form of BEEP ............................................................................................. 18.3 Status at Reset ................................................................................................................... 120 120 121 125 131 138 138 139 141 143 144 148 148 149 149 150 153 153 154 154 155 159 160 162 163 163 164 168 170 174 175 179 180 180 181 183 189 191 192 192 194 195 8 PD17933, 17934 19. LCD 19.1 19.2 19.3 19.4 19.5 19.6 19.7 19.8 CONTROLLER/DRIVER ........................................................................................................ Outline of LCD Controller/Driver ..................................................................................... LCD Drive Voltage Generation Block .............................................................................. LCD Segment Register ...................................................................................................... Segment Signal/General-Purpose Input Port Select Block ......................................... Common Signal Output and Segment Signal Output Timing Control Blocks .......... Common Signal and Segment Signal Output Waves ................................................... Using LCD Controller/Driver ............................................................................................ Status at Reset ................................................................................................................... 196 196 197 198 200 202 203 205 207 208 208 209 215 217 217 220 220 221 222 228 228 229 230 232 233 233 233 234 235 236 238 238 20. STANDBY ....................................................................................................................................... 20.1 Outline of Standby Function ............................................................................................ 20.2 Halt Function ...................................................................................................................... 20.3 Clock Stop Function .......................................................................................................... 20.4 Device Operation in Halt and Clock Stop Status .......................................................... 20.5 Cautions on Processing of Each Pin in Halt and Clock Stop Status ......................... 21. RESET ............................................................................................................................................ 21.1 Outline of Reset ................................................................................................................. 21.2 Reset by RESET Pin .......................................................................................................... 21.3 WDT&SP Reset ................................................................................................................... 22. INSTRUCTION SET ....................................................................................................................... 22.1 Outline of Instruction Set ................................................................................................. 22.2 Legend ................................................................................................................................. 22.3 Instruction List ................................................................................................................... 22.4 Assembler (RA17K) Embedded Macro Instruction ....................................................... 23. RESERVED SYMBOLS ................................................................................................................. 23.1 Data Buffer (DBF) ............................................................................................................... 23.2 System Registers (SYSREG) ............................................................................................ 23.3 LCD Segment Register ...................................................................................................... 23.4 Port Register ....................................................................................................................... 23.5 Register File (Control Register) ....................................................................................... 23.6 Peripheral Hardware Register .......................................................................................... 23.7 Others .................................................................................................................................. 24. ELECTRICAL CHARACTERISTICS ............................................................................................ 239 25. PACKAGE DRAWING .................................................................................................................. 243 26. RECOMMENDED SOLDERING CONDITIONS ........................................................................... 244 APPENDIX A. CAUTIONS ON CONNECTING CRYSTAL RESONATOR ...................................... 245 APPENDIX B. DEVELOPMENT TOOLS ........................................................................................... 246 9 PD17933, 17934 MEMO 10 PD17933, 17934 1. PIN FUNCTIONS 1.1 Pin Function List Pin No. 1 2 3 4 Symbol PIC0/TM0 P1C1/TM1 P1C2/AMIFC P1C3/FMIFC/ AMIFC Function Port 1C, timer event input pins, IF counter (for frequency count) input pin for the AM/FM. * PIC0 through P1C3 4-bit input port * TM0 and TM1 Timer event input pins * AMIFC IF counter input pin for AM * FMIFC IF counter input pin for FM At reset Reset by RESET pin Input (P1C0-P1C3) 80 5 32 VDD2 VDD1 VDD0 WDT&SP reset Input (P1C0-P1C3) Input (P1C0-P1C3) - On clock stop Output Form Power supply pins. Supply the same voltage to these pins. VDD2: Supplies power to the comparator and peripherals of the A/D converter, and to the IF counter. VDD1: Supplies power to the PLL. VDD0: Supplies power to all the internal circuits except the above. 6 7 8 NC EO0 EO1 No connection Output from the charge pump of the PLL frequency synthesizer. These pins output the result of comparing the phases of the divided frequency of local oscillation with the reference frequency. At reset Reset by RESET pin High-impedance output WDT&SP reset High-impedance output High-impedance output On clock stop - CMOS 3-state 9 10 VCOL VCOH Input of the local oscillation (VCO) frequency of the PLL. * VCOL * Active when HF or MF mode selected by program; otherwise; pulled down. * VCOH * Active when VHF mode selected by program; otherwise, pulled down. Because these input pins are connected to an internal AC amplifier, cut the DC component of the input signal with a capacitor. - 11 79 12 13 GND Ground - TEST RESET Test input pin. Be sure to connect this pin directly to GND. Reset input - - 11 PD17933, 17934 Pin No. 14 | 17 Symbol P2B0 | P2B3 Reset by RESET pin Input 18 19 P0A0 P0A1 Reset by RESET pin Output low level 20 | 23 P1A0 | P1A3 Reset by RESET pin Input 24 | 27 P1D0 | P1D3 Reset by RESET pin Input 28 | 31 P0B0/SCK P0B1/SI1/SO2 P0B2/SO1 P0B3/BEEP Function These pins form a 4-bit I/O port which can be set in input or output mode in 1-bit units. At reset WDT&SP reset Input Retained N-ch openOn clock stop drain On clock stop Output Form CMOS push-pull These pins form a 2-bit output port. At reset WDT&SP reset Output low level Retained These pins form a 4-bit I/O port which can be set in input or output mode in 1-bit units. At reset WDT&SP reset Input Retained On clock stop N-ch opendrain These pins form a 4-bit I/O port which can be set in input or output mode in 1-bit units. At reset WDT&SP reset Input Retained On clock stop N-ch opendrain Port P0B, the I/O pins of the serial interface and BEEP output pin. * P0B3 through P0B0 * 4-bit I/O port * Can be set in input or output mode in 1-bit units. * BEEP * BEEP output * SO1, SO2, SI1 Serial data output pins and serial data input pin when the 3-wire or 2-wire serial I/O mode of serial interface 1 is selected. * SCK * Serial clock I/O At reset Reset by RESET pin Input (P0B3-P0B0) WDT&SP reset Input (P0B3-P0B0) Retained On clock stop CMOS push-pull 33 34 37 38 35 36 39 CAPLCD0 CAPLCD1 CAPLCD2 CAPLCD3 REGLCD0 REGLCD1 REGLCD2 These pins can be used to connect capacitors for a double circuit to generate power to drive an LCD. Connect 0.33 F capacitors between CAPLCD0 and CAPLCD1 pins and between CAPLCD2 and CAPLCD3 pins. - Regulator output pins of power supply for LCD drive. Connect to GND with a 0.1 F capacitor. - 12 PD17933, 17934 Pin No. 40 | 43 Symbol COM0 | COM3 Reset by RESET pin Output low level 44 | 60 61 | 63 LCD0 | LCD16 P2A0/LCD17 P2A1/LCD18 P2A2/LCD19 Port 2A input port, the segment signal output pins of the LCD controller/driver. * P2A0 through P2A2 3-bit input port * LCD17 through LCD19 LCD segment output At reset Reset by RESET pin Input (P2A2-P2A0) 64 | 67 P0C0 | P0C3 Reset by RESET pin Output low level 68 INT 4-bit output At reset WDT&SP reset Output low level Retained - On clock stop WDT&SP reset Input (P2A2-P2A0) Retained CMOS push-pull On clock stop Function These pins output the common signals of the LCD controller/driver. At reset WDT&SP reset Output low level Output low level CMOS push-pull On clock stop Output Form CMOS 3-state These pins are the segment signal output pins of the LCD controller/driver. - Edge-detected vector interrupt input. Rising or falling edge is selectable. 69 70 71 | 74 XOUT XIN P2C0 | P2C3 Crystal resonator connection pin. - These pins form a 4-bit I/O port which can be set in the input or output mode in 1-bit units. At reset Reset by RESET pin Input WDT&SP reset Input Retained On clock stop CMOS push-pull 75 | 78 P0D0 P0D1/AD0 P0D2/AD1 P0D3/AD2 Port 0D input port, A/D converter input pins and to release the HALT and STOP modes. * P0D0 through P0D3 4-bit input port * AD0 through AD2 Analog input of A/D converter * HALT and STOP mode releasing Releases HALT or STOP mode when a high level is input. At reset Reset by RESET pin Input with pull-down resistor (P0D3-P0D0) WDT&SP reset Input with pull-down resistor (P0D3-P0D0) Retained On clock stop - 13 PD17933, 17934 1.2 Equivalent Circuits of Pins (1) P0B (P0B3/BEEP, P0B2/SO1, P0B1/SI1/SO2, P0B0/SCK) P2B (P2B3, P2B2, P2B1, P2B0) P2C (P2C3, P2C2, P2C1, P2C0) (I/O) VDD VDD (2) P1A (P1A3, P1A2, P1A1, P1A0) P1D (P1D3, P1D2, P1D1, P1D0) (I/O) VDD (3) P0A (P0A1, P0A0) (Output) 14 PD17933, 17934 (4) P0C (P0C3, P0C2, P0C1, P0C0) (Output) VDD (5) P0D (P0D3/AD2, P0D2/AD1, P0D1/AD0, P0D0) P1C (P1C3/FMIFC/AMIFC, P1C2/AMIFC, P1C1/TM1, PIC0/TM0) P2A (P2A2/LCD19, P2A1/LCD18, P2A0/LCD17) VDD (Input) High ON resistance (P0D only) (6) INT RESET (Schmitt trigger input) VDD (7) XOUT (Output), XIN (Input) VDD High ON resistance VDD XIN High ON resistance XOUT 15 PD17933, 17934 (8) EO1, EO0 (Output) VDD DWN UP (9) COM3 through COM0 (Output) VLCD0 VLCD1 (10) VCOH (Input) High ON resistance VDD VDD 16 PD17933, 17934 (11)VCOL (Input) High ON resistance VDD PLL disable signal High ON resistance VDD PLL disable signal 17 PD17933, 17934 1.3 Recommended Connections of Unused Pins It is recommended to connect the unused pins as follows: Table 1-1. Recommended Connections of Unused Pins Pin Name Port pins P0D3/AD2-P0D1/AD0,P0D0 P1C3/FMIFC/AMIFC Note 2 P1C2/AMIFC Note 2 P1C1/TM1 P1C0/TM0 P0A1, P0A0 P0C3-P0C0 P0B3/BEEP P0B2/SO1 P0B1/SI1/SO2 P0B0/SCK P1A3-P1A0 P1D3-P1D0 P2A2/LCD19 P2A1/LCD18 P2A0/LCD17 P2B3-P2B0 P2C3-P2C0 Pins other than port pins EO1 EO0 INT NC TEST VCOH VCOL Input Input - - Connect to GND via resistor Note 1. Leave unconnected. Directly connect to GND. Set to PLL disable via software and leave unconnected. Output Leave unconnected. I/O Note 3 Output Set each pin in port mode and connect it to VDD or GND via resistor. Set in low-level output mode via software and leave unconnected. Set in general-purpose input port mode via software, and connect each pin to VDD or GND via resistor. I/O Form Input Recommended Connection Connect each pin to GND via resistorNote 1 . Notes 1. If these pins are externally pulled up (connected to VDD via resistor) or down (connected to GND via resistor) with a high resistor, the pins almost go into a high-impedance state, increasing the current consumption (through current) of the port. Although the value of the pull-up or pull-down resistor varies depending on the application circuit, it generally is several 10 k. 2. The circuit of the general-purpose input port is designed not to increase the current consumption even in the high-impedance state. Do not set these pins in the AMIFC and FMIFC modes; otherwise, the current consumption will increase. 3. The I/O ports are set in the general-purpose input port mode at reset by the RESET pin and reset due to overflow/underflow of the watchdog timer or stack, and on execution of the clock stop instruction. 18 PD17933, 17934 1.4 Cautions on Using TEST Pin When VDD is applied to the TEST pin, the device is set in the test mode. Therefore, be sure to keep the wiring length of this pin as short as possible, and directly connect it to the GND pin. If the wiring length between the TEST pin and GND pin is too long, or if external noise is superimposed on the TEST pin, generating a potential difference between the TEST pin and GND pin, your program may not run normally. GND TEST Short 19 PD17933, 17934 2. PROGRAM MEMORY (ROM) 2.1 Outline of Program Memory Figure 2-1 outlines the program memory. As shown in this figure, the addresses of the program memory are specified by the program counter. The program memory has the following two major functions. * To store programs * To store constant data Figure 2-1. Outline of Program Memory Program counter Instruction ... Constant data ... 20 ... ... Address specification Program memory PD17933, 17934 2.2 Program Memory Figure 2-2 shows the configuration of the program memory. As shown in this figure, the program memory consists of: PD17933: 6144 x 16 bits (0000H-17FFH) PD17934: 8192 x 16 bits (0000H-1FFFH) Because all "instructions" are "one-word instructions", one instruction can be stored to one address of the program memory. As constant data, the contents of the program memory are read to the data buffer by using a table reference instruction. Figure 2-2. Configuration of Program Memory Address 0 0 0 0 H Reset start address 0 0 0 1 H Serial interface 1 interrupt vector 0 0 0 2 H Basic timer 1 interrupt vector 0 0 0 3 H Timer 0 interrupt vector 0 0 0 4 H INT pin interrupt vector Page 0 CALL addr instruction subroutine entry address BR @AR instruction branch address CALL @AR instruction subroutine entry address BR addr instruction branch address MOVT DBF, @AR instruction table reference address 0 7 FFH Page 1 0 FFFH Page 2 1 7 FFH ( PD17933) Page 3 1 FFFH ( PD17934) 16 bits 21 PD17933, 17934 2.3 Program Counter 2.3.1 Configuration of program counter Figure 2-3 shows the configuration of the program counter. As shown in this figure, the program counter consists of a 13-bit binary counter. Bits 11 and 12 of the program counter indicate a page. The program counter specifies an address of the program memory. Figure 2-3. Configuration of Program Counter PC12 PC11 PC10 PC9 PC8 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 Page PC 2.4 Flow of Program The flow of the program is controlled by the program counter that specifies an address of the program memory. The program flow when each instruction is executed is described below. Figure 2-4 shows the value that is set to the program counter when each instruction is executed. Table 2-4 shows the vector address when an interrupt is accepted. 2.4.1 Branch instruction (1) Direct branch ("BR addr") The branch destination addresses of the direct branch instruction are all the addressess of the program memory. (2) Indirect branch ("BR @AR") The branch destination addresses of the indirect branch instruction are all the addresses of the program memory. The addresses are 0000H through 17FFH in the PD17933, and 0000H through 1FFFH in the PD17934. Refer to 5.3 Address Register (AR). 22 PD17933, 17934 2.4.2 Subroutine (1) Direct subroutine call ("CALL addr") The first address of a subroutine that can be called by the direct subroutine instruction is in page 0 (addresses 0000H through 07FFH). (2) Indirect subroutine call (CALL @AR) The first addresses of a subroutine that can be called by the indirect subroutine call instruction are all the addresses of the program memory. The addresses are 0000H through 17FFH in the PD17933, and 0000H through 1FFFH in the PD17934. Refer to 5.3 Address Register (AR). 2.4.3 Table reference The addresses that can be referenced by the table reference instruction ("MOVT DBF, @AR") are all the addresses of the program memory. The addresses are 0000H through 17FFH in the PD17933, and 0000H through 1FFFH in the PD17934. Refer to 5.3 Address Register (AR) and 9.2.2 Table reference instruction (MOVT, DBF, @AR). 23 PD17933, 17934 Figure 2-4. Value of Program Counter Upon Execution of Instruction Program counter Instruction BR addr Page 0 Page 1 Page 2 Page 3 CALL addr 0 BR @AR CALL @AR Contents of address register MOVT DBF, @AR RET RETSK RETI Other instructions (including skip instruction) When interrupt is accepted Vector address of each interrupt Watchdog timer reset, reset by RESET pin 0 0 0 0 0 0 0 0 0 0 0 0 0 Increment Contents of address stack register (ASR) (return address) specified by stack pointer (SP) 0 Operand of instruction (addr) b12 0 0 1 1 b11 0 1 0 Operand of instruction (addr) 1 b10 Contents of Program Counter (PC) b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 Table 2-1. Interrupt Vector Address Order 1 2 3 4 Internal/External External Internal Internal Internal Interrupt Source INT pin Timer 0 Basic timer 1 Serial interface 1 Vector Address 0004H 0003H 0002H 0001H 24 PD17933, 17934 2.5 Cautions on Using Program Memory (1) PD17933 The program memory of the PD17933 is assigned to addresses 0000H through 17FFH. However, addresses that can be specified by the program counter (PC) are 0000H through 1FFFH, therefore, be careful on the following points when specifying the program memory addresses. * Write a branch instruction when writing an instruction to address 17FFH. * Do not write anything to addresses 1800H through 1FFFH. * Do not branch to addresses 1800H through 1FFFH. (2) PD17934 The program memory of the PD17934 is assigned to addresses 0000H through 1FFFH. Be careful on the following points. * Write a branch instruction when writing an instruction to address 1FFFH. 25 PD17933, 17934 3. ADDRESS STACK (ASK) 3.1 Outline of Address Stack Figure 3-1 outlines the address stack. The address stack consists of a stack pointer and address stack registers. The address of an address stack register is specified by the stack pointer. The address stack saves a return address when a subroutine call instruction is executed or when an interrupt is accepted. The address stack is also used when the table reference instruction is executed. Figure 3-1. Outline of Address Stack Stack pointer Address specification Address stack register Return address 3.2 Address Stack Register (ASR) Figure 3-2 shows the configuration of the address stack register. The address stack register consists of sixteen 13-bit registers ASR0 through ASR15. Actually, however, it consists of fifteen 13-bit registers (ASR0 through ASR14) because no register is allocated to ASR15. The address stack saves a return address when a subroutine is called, when an interrupt is accepted, and when the table reference instruction is executed. 26 PD17933, 17934 Figure 3-2. Configuration of Address Stack Register Stack pointer (SP) Bit b3 b2 b1 b0 0H Address Address stack register (ASR) Bit b12 b11 b10 b9 b8 b7 b6 ASR0 b5 b4 b3 b2 b1 b0 SP3 SP2 SP1 SP0 1H ASR1 2H ASR2 3H ASR3 4H ASR4 5H ASR5 6H ASR6 7H ASR7 8H ASR8 9H ASR9 AH ASR10 BH ASR11 CH ASR12 DH ASR13 EH ASR14 FH ASR15 (Undefined) Cannot be used 27 PD17933, 17934 3.3 Stack Pointer (SP) 3.3.1 Configuration and function of stack pointer Figure 3-3 shows the configuration and functions of the stack pointer. The stack pointer consists of a 4-bit binary counter. It specifies the address of an address stack register. A value can be directly read from or written to the stack pointer by using a register manipulation instruction. Figure 3-3. Configuration and Function of Stack Pointer Name Flag symbol b3 b2 b1 b0 Stack pointer (SP) 01H R/W ( S P 3 ( 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 ( S P 2 ( 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 ( S P 1 ( 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 ( S P 0 ( 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Address Read/Write Specifies address of address stack register (ASR) Address 0 (ASR0) Address 1 (ASR1) Address 2 (ASR2) Address 3 (ASR3) Address 4 (ASR4) Address 5 (ASR5) Address 6 (ASR6) Address 7 (ASR7) Address 8 (ASR8) Address 9 (ASR9) Address 10 (ASR10) Address 11 (ASR11) Address 12 (ASR12) Address 13 (ASR13) Address 14 (ASR14) Setting prohibited At reset Reset by RESET pin WDT&SP reset 1 1 1 1 1 1 1 1 Clock stop Retained Reset by RESET pin : Reset by RESET pin WDT&SP reset Clock stop : Reset by watchdog timer and stack pointer : Upon execution of clock stop instruction 28 PD17933, 17934 3.4 Operation of Address Stack 3.4.1 Subroutine call instruction ("CALL addr", "CALL @AR") and return instruction ("RET", "RETSK") When a subroutine call instruction is executed, the value of the stack pointer is decremented by one, and the return address is stored to an address stack register specified by the stack pointer. When the return instruction is executed, the contents of the address stack register (return address) specified by the stack pointer are restored to the program counter, and the value of the stack pointer is incremented by one. 3.4.2 Table reference instruction ("MOVT DBF, @AR") When the table reference instruction is executed, the value of the stack pointer is incremented by one, and the return address is stored to an address stack register specified by the stack pointer. Next, the contents of the program memory specified by the address register are read to the data buffer, the contents of the address stack register (return value) specified by the stack pointer are restored to the program counter, and the value of the stack pointer is incremented by one. 3.4.3 When interrupt is accepted and on execution of return instruction ("RETI") When an interrupt is accepted, the value of the stack pointer is decremented by one, and the return address is stored to an address stack register specified by the stack pointer. When the return instruction is executed, the contents of an address stack register (return value) specified by the stack pointer are restored to the program counter, and the value of the stack pointer is incremented by one. 3.4.4 Address stack manipulation instruction ("PUSH AR", "POP AR") When the "PUSH" instruction is executed, the value of the stack pointer is decremented by one, and the contents of the address register are transferred to an address stack register specified by the stack pointer. When the "POP" instruction is executed, the contents of an address stack register specified by the stack pointer are transferred to the address register, and the value of the stack pointer is incremented by one. 29 PD17933, 17934 3.5 Cautions on Using Address Stack 3.5.1 Nesting level and operation on overflow The value of address stack register (ASR15) is "undefined" when the value of the stack pointer is 0FH. Accordingly, if a subroutine call exceeding 15 levels, or an interrupt is used without manipulating the stack, execution returns to an "undefined" address. 3.5.2 Reset on detection of overflow or underflow of address stack Whether the device is reset on detection of overflow or underflow of the address stack can be specified by program. At reset, the program is started from address 0, and some control registers are initialized. This reset function is valid at reset by the RESET pin. For details, refer to 21. RESET. 30 PD17933, 17934 4. DATA MEMORY (RAM) 4.1 Outline of Data Memory Figure 4-1 outlines the data memory. As shown in the figure, system registers, a data buffer, port registers, LCD segment registers, and control registers are located on the data memory. The data memory stores data, transfers data with the peripheral hardware or ports, and controls the CPU. 31 PD17933, 17934 Figure 4-1. Outline of Data Memory Peripheral hardware Data transfer Column address 0 0 1 Row address 2 3 4 5 6 7 Port registers Port registers Port registers BANK0 BANK1 BANK2 BANK3 ... 1 2 3 4 5 6 7 8 9 A B C D E F Data buffer Data memory LCD segment register BANK15 Note 2 ... BANK14 Note 1 System registers Data transfer Ports LCD Condition setting Peripheral hardware Data transfer Notes 1. LCD segment registers are allocated to addresses 5CH through 6FH of BANK14. 2. Control registers are allocated to addresses 00H through 6FH of BANK15. Port input/output select registers are allocated to 60H through 6FH. Cautions 1. Never write anything to address 31H of BANK15 because this address is a test mode area. 2. Address 5BH is not provided to BANK4 through BANK14. 32 PD17933, 17934 4.2 Configuration and Function of Data Memory Figure 4-2 shows the configuration of the data memory. As shown in this figure, the data memory is divided into several banks with each bank made up of a total of 128 nibbles with 7H row addresses and 0FH column addresses. The data memory can be divided into five functional blocks. Each block is described in 4.2.1 through 4.2.6 below. The contents of the data memory can be operated on, compared, judged, and transferred in 4-bit units with a single data memory manipulation instruction. Table 4-1 lists the data memory manipulation instructions. 4.2.1 System registers (SYSREG) The system registers are allocated to addresses 74H through 7FH. Because the system registers are allocated to all banks, the same system registers exist at addresses 74H through 7FH of any bank. For details, refer to 5. SYSTEM REGISTER (SYSREG). 4.2.2 Data buffer (DBF) The data buffer is allocated to addresses 0CH through 0FH of BANK 0. For details, refer to 9. DATA BUFFER (DBF). 4.2.3 Port registers The port registers are allocated to addresses 70H through 73H of BANKs 0 through 2. For details, refer to 11. GENERAL-PURPOSE PORTS. 4.2.4 Control registers and port input/output select registers The control registers are allocated to addresses 00H through 6FH of BANK 15. Of these registers, the port input/output select registers are allocated to addresses 60H through 6FH of BANK15. Addresses 00H through 3FH of BANK15, to which control registers are allocated, also overlap addresses 00H through 3FH of the register file. For details, refer to 8. REGISTER FILE (RF) AND CONTROL REGISTERS. 4.2.5 LCD segment registers The LCD segment registers consists of a total of 20 nibbles at addresses 5CH through 6FH of BANK15 of the data memory. For details, refer to 8.4 LCD Segment Registers and 19. LCD CONTROLLER/DRIVER. 4.2.6 General-purpose data memory The general-purpose data memory is allocated to the addresses of the data memory excluding those of the system registers, control registers, port registers, port input/output selection registers, and LCD segment register. The general-purpose data memory consists of a total of 448 nibbles of the 112 nibbles each of BANKs 0 through 3. 33 PD17933, 17934 Figure 4-2. Configuration of Data Memory BANK0 Column address 0 1 2 3 4 5 6 7 8 9 ABCDE F 0 1 2 3 4 5 6 7 0 1 Row address Data memory 2 3 4 5 6 7 Port registerNote 1 System registers (SYSREG)Note 2 General registers Row address Column address 0123456789ABCDEF Data buffer BANK0 BANK1 BANK2 BANK14 BANK15 System registers Row address Row address Row address Row address Notes 1. The high-order 2 bits of 70H are fixed to 0. 2. The same system register exists. 3. Address 71H of BANK1, and the high-order 1 bit and address 73H of BANK2 are fixed to 0. Cautions 1. Never write anything to address 31H of BANK15 because this address is a test mode area. 2. Address 5BH is not provided to BANK4 through BANK14. ... BANK1-BANK2 Column address 0123456789ABCDEF 0 1 2 3 4 5 6 7 Port registerNote 3 System registers (SYSREG)Note 2 BANK3 Column address 0123456789ABCDEF 0 1 2 3 4 5 6 7 Fixed to 0 System registers (SYSREG)Note 2 BANK14 Column address 0123456789ABCDEF 0 1 2 3 4 5 6 7 Fixed to 0 LCD segment register System registers (SYSREG)Note 2 Unmounted BANK15 Column address 0123456789ABCDEF 0 1 2 3 4 5 6 7 Fixed to 0 Fixed to 0 Port input/output selection registers System registers (SYSREG)Note 2 Control register 34 PD17933, 17934 Table 4-1. Data Memory Manipulation Instructions Function Operation Add Instruction ADD ADDC SUB SUBC AND OR XOR SKE SKGE SKLT SKNE MOV LD ST SKT SKF Subtract Logic Compare Transfer Judge 4.3 Data Memory Addressing Figure 4-3 shows address specification of the data memory. An address of the data memory is specified by a bank, row address, and column address. A row address and a column address are directly specified by a data memory manipulation instruction. However, a bank is specified by the contents of a bank register. For the details of the bank register, refer to 5. SYSTEM REGISTER (SYSREG). Figure 4-3. Address Specification of Data Memory Bank b3 Data memory address Bank register b2 b1 b0 Row address b2 b1 b0 Column address b3 b2 b1 b0 Instruction operand 35 PD17933, 17934 4.4 Cautions on Using Data Memory 4.4.1 At reset by RESET pin The contents of the general-purpose data memory are "undefined" at reset by RESET pin. Initialize the data memory as necessary. 4.4.2 Cautions on data memory not provided If a data memory manipulation instruction that reads the data memory is executed to a data memory address not provided, undefined data is read. Nothing is changed even if data is written to such an address. 36 PD17933, 17934 5. SYSTEM REGISTERS (SYSREG) 5.1 Outline of System Registers Figure 5-1 shows the location of the system registers on the data memory and their outline. As shown in the figure, the system registers are allocated to addresses 74H through 7FH of all the banks of the data memory. Therefore, identical system registers exist at addresses 74H through 7FH of any bank. Because the system registers are located on the data memory, they can be manipulated by all data memory manipulation instructions. Seven types of system registers are available depending on function. Figure 5-1. Location and Outline of System Registers on Data Memory Column address 0 0 1 Row address 2 3 4 5 6 7 BANK0 BANK1 BANK2 BANK3 Data memory 1 2 3 4 5 6 7 8 9 A B C D E F Remark Address 5BH is not provided to BANK4 through BANK14. Address Name 74H 75H 76H 77H 78H Window register (WR) 79H Bank register (BANK) 7AH 7BH Index register (IX) Data memory row address pointer (MP) Function Controls program memory address Transfers Specifies Modifies address of data memory Specifies data with register file bank of data memory address of general register 7CH 7DH 7EH 7FH ... BANK14 BANK15 System register ... Address register (AR) General register Program pointer (RP) status word (PSWORD) Controls operation 37 PD17933, 17934 5.2 System Register List Figure 5-2 shows the configurations of the system registers. Figure 5-2. Configuration of System Registers Address Name 74H 75H 76H 77H 78H 79H 7AH 7BH 7CH 7DH 7EH 7FH System registers Address register (AR) Window register (WR) Bank register Index register (IX) General register Program pointer (RP) status word (PSWORD) (BANK) Data memory row address pointer (MP) Symbol AR3 AR2 AR1 AR0 WR BANK IXH MPH IXM MPL IXL RPH RPL PSW Bit Data b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 M P E (MP) (IX) (RP) BCCZ I CMY DP X E 38 PD17933, 17934 5.3 Address Register (AR) 5.3.1 Configuration of address register Figure 5-3 shows the configuration of the address register. As shown in the figure, the address register consists of 16 bits of system register addresses 74H through 77H (AR3 through AR0). Figure 5-3. Configuration of Address Register Address Name Symbol Bit Data b3 74H 75H 76H 77H Address register (AR) AR3 b2 b1 b0 b3 AR2 b2 b1 b0 b3 AR1 b2 b1 b0 b3 AR0 b2 b1 b0 M S B At reset L S B Reset by RESET pin WDT&SP reset Clock stop 0 0 Retained 0 0 Retained 0 0 Retained 0 0 Retained Reset by RESET pin : Reset by RESET pin WDT&SP reset Clock stop : Reset by watchdog timer and stack pointer : On execution of clock stop instruction 39 PD17933, 17934 5.3.2 Function of address register The address register specifies a program memory address when the table reference instruction ("MOVT DBF, @AR"), stack manipulation instruction ("PUSH AR", "POP AR"), indirect branch instruction ("BR @AR"), or indirect subroutine call instruction ("CALL @AR") is executed. A dedicated instruction ("INC AR") is available that can increment the contents of the address instruction by one. The following paragraphs (1) through (5) describe the operation of the address register when the respective instructions are executed. (1) Table reference instruction ("MOVT DBF, @AR") When the table reference instruction is executed, the constant data (16 bits) of a program memory address specified by the contents of the address register are read to the data buffer. The constant data that can be specified by the address register is stored to address 0000H to 17FFH in the case of the PD17933, and address 0000H to 1FFFH in the case of the PD17934. (2) Stack manipulation instruction ("PUSH AR", "POP AR") When the "PUSH AR" instruction is executed, the value of the stack pointer is decremented by one, and the contents of the address register (AR) are transferred to an address stack register specified by the stack pointer whose value has been decremented by one. When the "POP AR" instruction is executed, the contents of an address stack register specified by the stack pointer are transferred to the address register, and the value of the stack pointer is incremented by one. (3) Indirect branch instruction ("BR @AR") When this instruction is executed, the program branches to a program memory address specified by the contents of the address register. The branch address that can be specified by the address register is 0000H to 17FFH in the case of the PD17933, and 0000H to 1FFFH in the case of the PD17934. (4) Indirect subroutine call instruction ("CALL @AR") The subroutine at a program memory address specified by the contents of the address register can be called. The first address of the subroutine that can be specified by the address register is 0000H to 17FFH in the case of the PD17933, and 0000H to 1FFFH in the case of the PD17934. (5) Address register increment instruction ("INC AR") This instruction increments the contents of the address register by one. 5.3.3 Address register and data buffer The address register can transfer data as part of the peripheral hardware via the data buffer. For details, refer to 9. DATA BUFFER (DBF). 5.3.4 Cautions on Using Address Register Because the address register is configured in 16 bits, it can specify an address up to FFFFH. However, the program memory exists at addresses 0000H through 17FFH in the case of the PD17933 and addresses 0000H through 1FFFH in the case of the PD17934. Therefore, the maximum value that can be set to the address register of the PD17933 is address 17FFH. In the case of the PD17934, it is address 1FFFH. 40 PD17933, 17934 5.4 Window Register (WR) 5.4.1 Configuration of window register Figure 5-4 shows the configuration of the window register. As shown in the figure, the window register consists of 4 bits of system register address 78H (WR). Figure 5-4. Configuration of Window Register Address Name 78H Window register (WR) Symbol Bit Data b3 M S B At reset Reset by RESET pin WDT&SP reset Clock stop WR b2 b1 b0 L S B Undefined Retained 5.4.2 Function of window register The window register is used to transfer data with the register file (RF) to be described later. Data transfer between the window register and register file is manipulated by using dedicated instructions "PEEK WR, rf" and "POKE, rf WR" (rf: address of register file). The following paragraphs (1) and (2) describe the operation of the window register when these instructions are executed. For further information, also refer to 8. REGISTER FILE (RF) AND CONTROL REGISTERS. (1) "PEEK WR, rf" instruction When this instruction is executed, the contents of the register file addressed by "rf" are transferred to the window register. (2) "POKE rf, WR" instruction When this instruction is executed, the contents of the window register are transferred to the register file addressed by "rf". 41 PD17933, 17934 5.5 Bank Register (BANK) 5.5.1 Configuration of bank register Figure 5-5 shows the configuration of the bank register. As shown in the figure, the bank register consists of 4 bits of system register address 79H (BANK). Figure 5-5. Configuration of Bank Register Address Name 79H Bank register (BANK) Symbol Bit Data b3 M S B At reset Reset by RESET pin WDT&SP reset Clock stop 0 0 Retained BANK b2 b1 b0 L S B 5.5.2 Function of bank register The bank register specifies a bank of the data memory. Table 5-1 shows the relationships between the value of the bank register and a bank of the data memory that is specified. Because the bank register is one of the system registers, its contents can be rewritten regardless of the bank currently specified. When manipulating a bank register, therefore, the status of the bank at that time is irrelevant. Table 5-1. Data Memory Bank Specification Bank Register (BANK) b3 0 0 0 0 1 1 b2 0 0 0 0 1 1 b1 0 0 1 1 1 1 b0 0 1 0 1 0 1 BANK0 BANK1 BANK2 BANK3 BANK14 BANK15 Bank of Data Memory Remark Caution Addresses 00H through 5BH are not provided to BANK4 through BANK14. The area to which the data memory is allocated differs depending on the model. For details, refer to Figure 4-2 Configuration of Data Memory. 42 PD17933, 17934 5.6 Index Register (IX) and Data Memory Row Address Pointer (MP: memory pointer) 5.6.1 Configuration of index register and data memory row address pointer Figure 5-6 shows the configuration of the index register and data memory row address pointer. As shown in the figure, the index register consists of an index register (IX) made up of 11 bits (the low-order 3 bits (IXH) of system register address 7AH, and 7BH and 7CH (IXM, IXL)) and an index enable flag (IXE) at the lowest bit position of 7FH (PSW). The data memory row address pointer (memory pointer) consists of a data memory row address pointer (MP) that is made up of 7 bits of the low-order 3 bits of 7AH (MPH) and 7BH (MPL), and a data memory row address pointer enable flag (memory pointer enable flag: MPE) at the lowest bit position of 7AH (MPH). In other words, the high-order 7 bits of the index register are shared with the data memory row address pointer Figure 5-6. Configuration of Index Register and Data Memory Row Address Pointer Address Name 7AH 7BH Index register (IX) 7CH 7EH 7FH Program status word (PSWORD) Memory pointer (MP) Symbol IXH MPH Bit Data M P E b3 b2 M S B M S B MP 0 0 Retained 0 0 Retained At reset Reset by RESET pin WDT&SP reset Clock stop R: retained IX L S B 0 0 Retained b1 b0 b3 IXM MPL b2 b1 b0 b3 b2 b1 b0 L S B b3 b2 b1 IXL PSW b0 b3 b2 b1 b0 I X E 0 0 R 43 PD17933, 17934 5.6.2 Functions of index register and data memory row address pointer The index register and data memory row address pointer modify the addresses of the data memory. The following paragraphs (1) and (2) describe their functions. A dedicated instruction ("INC IX") that increments the value of the index register by one is available. For the details of address modification, refer to 7. ALU (Arithmetic Logic Unit) BLOCK. (1) Index register (IX) When a data memory manipulation instruction is executed, the data memory address is modified by the contents of the index register. This modification, however, is valid only when the IXE flag is set to 1. To modify the address, the bank, row address, and column address of the data memory are ORed with the contents of the index register, and the instruction is executed to a data memory address (called real address) specified by the result of this OR operation. All data memory manipulation instructions are subject to address modification by the index register. The following instructions, however, are not subject to address modification by the index register. INC INX MOVT PUSH POP PEEK POKE GET PUT BR BR AR IX DBF, @AR AR AR WR,rf rf,WR DBF,p p, DBF addr @AR RORC r CALL CALL RET RETSK RETI EI DI STOP s HALT h NOP addr @AR (2) Data memory row address pointer (MP) When the general register indirect transfer instruction ("MOV @r,m" or "MOV m,@r") is executed, the indirect transfer destination address is modified. This modification, however, is valid only when the MPE flag is set to 1. To modify the address, the bank and row address at the indirect transfer destination are replaced by the contents of the data memory row address pointer. Instructions other than the general register indirect transfer instruction are not subject to address modification. (3) Index register increment instruction ("INC IX") This instruction increments the contents of the index register by one. Because the index register is configured of 10 bits, its contents are incremented to "000H" if the "INC IX" instruction is executed when the contents of the index register are "3FFH". 44 PD17933, 17934 5.7 General Register Pointer (RP) 5.7.1 Configuration of General Register Pointer Figure 5-7 shows the configuration of the general register pointer. As shown in the figure, the general register pointer consists of 7 bits including 4 bits of system register address 7DH (RPH) and the high-order 3 bits of address 7EH (RPL). Figure 5-7. Configuration of General Register Pointer Address Name 7DH General register pointer (RP) 7EH Symbol Bit Data b3 M S B At reset Reset by RESET pin WDT&SP reset Clock stop RPH b2 b1 b0 b3 RPL b2 b1 L S B b0 B C D 0 0 Retained 0 0 Retained 45 PD17933, 17934 5.7.2 Function of general register pointer The general register pointer specifies a general register on the data memory. Figure 5-8 shows the addresses of the general registers specified by the general register pointer. As shown in the figure, a bank is specified by the high-order 4 bits (RPH: address 7DH) of the general register pointer, and a row address is specified by the low-order 3 bits (RPL: address 7EH). Because the valid number of bits of the general register pointer is 7, all the row addresses (0H through 7FH) of all the banks can be specified as general registers. For the details of the operation of the general register, refer to 6. GENERAL REGISTER (GR). Figure 5-8. Address of General Register Specified by General Register Pointer General register pointer (RP) RPH b3 RPL b0 b3 b2 b1 b2 b1 b0 M S B L S B B C D Specifies row address of each bank Specifies bank Bank 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 BANK0 Row address 0H 1H 2H 3H 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 1 1 0 1 0 1 BANK15 4H 5H 6H 7H Remark Address 5BH is not provided to BANK4 through BANK14. 5.7.3 Cautions on using general register pointer The lowest bit of address 7EH (RPL) of the general register pointer is allocated as the BCD flag of the program status word. When rewriting RPL, therefore, pay attention to the value of the BCD flag. 46 PD17933, 17934 5.8 Program Status Word (PSWORD) 5.8.1 Configuration of program status word Figure 5-9 shows the configuration of the program status word. As shown in the figure, th program status word consists of a total of 5 bits including the lowest bit of system register address 7EH (RPL) and 4 bits of address 7FH (PSW). Each bit of the program status word has its own function. The 5 bits of the program status word are BCD flag (BCD), compare flag (CMP), carry flag (CY), zero flag (Z), and index enable flag (IXE). Figure 5-9. Configuration of Program Status Word Address Name 7EH 7FH Program status word (PSWORD) Symbol Bit Data b3 RPL b2 b1 b0 B C D b3 C M P PSW b2 C Y b1 Z b0 I X E At reset Reset by RESET pin WDT&SP reset Clock stop 0 0 Retained 0 0 Retained 47 PD17933, 17934 5.8.2 Function of program status word The program status word is a register that sets the conditions under which the ALU (Arithmetic Logic Unit) executes an operation or data transfer, or indicates the result of an operation. Table 5-2 outlines the function of each flag of the program status word. For details, refer to 7. ALU (Arithmetic Logic Unit) BLOCK. Table 5-2. Outline of Function of Each Flag of Program Status Word (RP) Program Status Word (PSWORD) RPL b3 b2 b1 b0 B C D b3 C M P PSW b2 C Y b1 Z b0 I X E Flag Name Index enable flag (IXE) Function Modifies address of data memory when data memory manipulation instruction is exeuted. 0 : Does not modify 1 : Modifies Zero flag (Z) Indicates result of arithmetic operation is zero. Status of this flag differs depending on contents of compare flag. Carry flag (CY) Indicates occurrence of carry or borrow as result of execution of addition or subtraction instruction. This flag is reset to 0 if no carry or borrow occurs. It is set to 1 if carry or borrow occurs. This flag is also used as shift bit of "RORC r" instruction. Compare flag (CMP) Indicates whether result of arithmetic operation is stored to data memory or general register. 0 : Stores result. 1 : Does not store result. BCD flag (BCD) Indicates whether arithmetic operation is performed in decimal or binary. 0 : Binary operation 1 : Decimla operation 5.8.3 Cautions on using program status word When an arithmetic operation (addition or subtraction) is executed to the program status word, the "result" of the arithmetic operation is stored. For example, even if an operation that generates a carry is executed, if the result of the operation is 0000B, 0000B is stored to the PSW. 48 PD17933, 17934 6. GENERAL REGISTER (GR) 6.1 Outline of General Register Figure 6-1 outlines the general register. As shown in the figure, the general register is specified in the data memory by the general register pointer. The bank and row address of the general register are specified by the general register pointer. The general register is used to transfer or operate data between data memory addresses. Figure 6-1. Outline of General Register Column address Data memory General register pointer Row address General register Transfer, operation BANK0 BANK1 BANK2 BANK3 BANK14 BANK15 System register Remark Address 5BH is not provided to BANK4 through BANK14. 6.2 General Register The general register consists of 16 nibbles (16 x 4 bis) of the same row address on the data memory. For the range of the banks and row addresses that can be specified by the general register pointer as a general register, refer to 5.7 General Register Pointer (RP). The 16 nibbles of the same row address specified as a general register operate or transfer data with the data memory by a single instruction. In other words, operation or data transfer between data memory addresses can be executed by a single instruction. The general register can be controlled by the data memory manipulation instruction, like the other data memory areas. 49 PD17933, 17934 6.3 Generating Address of General Register by Each Instruction The following sections 6.3.1 and 6.3.2 explain how the address of the general register is generated when each instruction is executed. For the details of the operation of each instruction, refer to 7. ALU (Arithmetic Logic Unit) BLOCK. 6.3.1 Add ("ADD r, m", "ADDC r, m") , subtract ("SUB r, m", "SUBC r, m") , logical operation ("AND r, m", "OR r, m", "XOR r, m"), direct transfer ("LD r, m", "ST m, r"), and rotation ("RORC r") instructions Table 6-1 shows the address of the general register specified by operand "r" of an instruction. Operand "r" of an instruction specifies only a column address. Table 6-1. Generating Address of General Register Bank b3 General register address b2 b1 b0 Row address b2 b1 b0 Column address b3 b2 r b1 b0 Contents of general register pointer 6.3.2 Indirect transfer ("MOV @r, m", "MOV m, @r") instruction Table 6-2 shows a general register address specified by instruction operand "r" and an indirect transfer address specified by "@r". Table 6-2. Generating Address of General Register Bank b3 General register address Contents of general register pointer Indirect transfer address Same as data memory Contents of "r" r b2 b1 b0 Row address b2 b1 b0 Column address b3 b2 b1 b0 6.4 Cautions on Using General Register 6.4.1 Row address of general register Because the row address of the general register is specified by the general register pointer, the currently specified bank may differ from the bank of the general register. 6.4.2 Operation between general register and immediate data No instruction is available that executes an operation between the general register and immediate data. To execute an operation between the general register and immediate data, the general register must be treated as a data memory area. 50 PD17933, 17934 7. ALU (Arithmetic Logic Unit) BLOCK 7.1 Outline of ALU Block Figure 7-1 outlines the ALU block. As shown in the figure, the ALU block consists of an ALU, temporary registers A and B, program status word, decimal adjustment circuit, and memory address control circuit. The ALU operates on, judges, compares, rotates, and transfers 4-bit data in the data memory. Figure 7-1. Outline of ALU Block Data bus Address control Temporary register A Temporary register B Program status word Index modification memory pointer Carry/borrow/zero detection/decimal/storage specification ALU * Arithmetic operation * Logical operation * Bit judgment * Comparison * Rotation * Transfer Data memory Decimal adjustment 51 PD17933, 17934 7.2 Configuration and Function of Each Block 7.2.1 ALU The ALU performs arithmetic operation, logical operation, bit judgment, comparison, rotation, and transfer of 4-bit data according to instructions specified by the program. 7.2.2 Temporay registers A and B Temporary registers A and B temporarily store 4-bit data. These registers are automatically used when an instruction is executed, and cannot be controlled by program. 7.2.3 Program status word The program status word controls the operation of and stores the status of the ALU. For further information on the program status word, also refer to 5.8 Program Status Word (PSWORD). 7.2.4 Decimal adjustment circuit The decimal adjustment circuit converts the result of an arithmetic operation into a decimal number if the BCD flag of the program status word is set to "1" during arthmetic operations. 7.2.5 Address control circuit The address control circuit specifies an address of the data memory. At this time, address modification by the index register and data memory row address pointer is also controlled. 7.3 ALU Processing Instruction List Table 7-1 lists the ALU operations when each instruction is executed. Table 7-2 shows how data memory addresses are modified by the index register and data memory row address pointer. Table 7-3 shows decimal adjustment data when a decimal operation is performed. 52 PD17933, 17934 Table 7-1. List of ALU Processing Instruction Operations ALU Function Instruction Difference in Operation Depending on Program Status Word (PSWORD) Value of Value of BCD flag CMP flag ADD r, m m, #n4 ADDC r, m m, #n4 Subtract SUB r, m m, #n4 SUBC r, m m, #n4 Logical operation AND OR r, m 1 1 1 0 0 1 0 0 Operation Operation of CY flag Set if carry or borrow occurs; Operation of Z flag Address Modification Index Memory pointer Add Stores result of binary operation Set if result of operation is 0000B; otherwise, reset Modifies Does not modify Does not store result otherwise, reset Retains status if result of operation of binary operation Stores result of decimal operation Does not store result of decimal operation is 0000B; otherwise, reset Set if result of operation is 0000B; otherwise, reset Retains status if result of operation is 0000B; otherwise, reset Retains previous Retains previous status status Modifies Does not modify Don't care Don't care Not affected m, #n4 (retained) (retained) r, m m, #n4 XOR r, m m, #n4 Judge SKT SKF m, #n m, #n Don't care Don't care Not affected (retained) (reset) Retains previous Retains previous status status Retains previous Retains previous status status Modifies Does not modify Modifies Does not modify Compare SKE m, #n4 Don't care Don't care Not affected SKNE m, #n4 (retained) (retained) SKGE m, #n4 SKLT Transfer LD ST MOV m, #n4 r, m m, r m, #n4 @r, m m, @r Rotate RORC r Don't care Don't care Not affected (retained) (retained) Don't care Don't care Not affected (retained) (retained) Retains previous Retains previous status status Modifies Does not modify Modifies Value of b0 of general register Retains previous status Does not Does not modify modify 53 PD17933, 17934 Table 7-2. Modification of Data Memory Address and Indirect Transfer Address by Index Register and Data Memory Row Address Pointer IXE MPE General Register Address Specified by "r" Bank Row address Column address Data Memory Address Specified by "m" Bank Row address Column address Indirect Transfer Address Specified by "@r" Bank Row address Column address b3 b2 b1 b0 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b2 b1 b0 b3 b2 b1 b0 0 0 RP r BANK m BANK mR (r) 0 1 ditto ditto MP (r) 1 0 ditto BANK Logical IX m OR BANK Logical IXH, IXM mR OR (r) 1 1 ditto ditto MP (r) BANK IX IXE IXH IXM IXL m mR mC MP r RP (x) : bank register : index register : index enable flag : bits 10 through 8 of index register : bits 7 through 4 of index register : bits 3 through 0 of index register : data memory address indicated by mR, mC : data memory row address (high-order) : data memory column address (low-order) : data memory row address pointer : general register column address : general register pointer : contents addressed by x x: direct address such as "m" and "r" MPE : memory pointer enable flag 54 PD17933, 17934 Table 7-3. Decimal Adjustment Data Operation Hexadecimal Addition Result 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 CY 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Operation result 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1010B 1011B 1100B 1101B 1110B 1111B 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1010B 1011B 1100B 1101B 1110B 1111B Decimal Addition CY 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Operation result 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1110B 1111B 1100B 1101B 1110B 1111B 1100B 1101B 1010B 1011B 1100B 1101B Operation Hexadecimal Addition Result 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 CY 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Operation result 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1010B 1011B 1100B 1101B 1110B 1111B 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1010B 1011B 1100B 1101B 1110B 1111B Decimal Addition CY 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Operation result 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1100B 1101B 1110B 1111B 1100B 1101B 1110B 1111B 1100B 1101B 1110B 1111B 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B Remark Decimal adjustment is not correctly carried out in the shaded area in the above table. 55 PD17933, 17934 7.4 Cautions on Using ALU 7.4.1 Cautions on execution operation to program status word If an arithmetic operation is executed to the program status word, the result of the operation is stored to the program status word. The CY and Z flags in the program status word are usually set or reset by the result of the arithmetic operation. If an arithmetic operation is executed to the program status word itself, the result of the operation is stored to the program status word, and consequently, it cannot be judged whether a carry or borrow occurs or whether the result of the operation is zero. If the CMP flag is set, however, the result of the operation is not stored to the program status word. Therefore, the CY and Z flags are set or reset normally. 7.4.2 Cautions on executing decimal operation The decimal operation can be executed only when the result of the operation falls within the following ranges: (1) Result of addition : 0 to 19 in decimal (2) Result of subtraction: 0 to 9 or -10 to -1 in decimal If a decimal operation is executed exceeding or falling below the above ranges, the result is a value greater than 1010B (0AH). 56 PD17933, 17934 8. REGISTER FILE (RF) AND CONTROL REGISTERS 8.1 Outline of Register File Figure 8-1 outlines the register file. As shown in the figure, the rgister file consists of the control registers existing on addresses 00H through 3FH of BANK15 in the data memory, and a portion overlapping the data memory specified by the BANK register. The control registers set conditions of the peripheral hardware units. The data on the register file can be read or written via window register. Figure 8-1. Outline of Register File Register file 0 Control register (00H-3FH of BANK15 in data memory) Peripheral hardware 1 2 Row address 3 4 (Same space as data memory specified by BANK register) Data manipulation via window register 5 6 7 System register Window register 57 PD17933, 17934 8.2 Configuration and Function of Register File Figure 8-2 shows the configuration of the register file and the relationships between the register file and data memory. The register file is assigned addresses in 4-bit units, like the data memory, and consists of a total of 128 nibbles with row addresses 0H through 7FH and column addresses 0H through 0FH. Addresses 00H through 3FH are overlapping addresses 00H through 3FH of BANK15 and called control registers that sets the conditions of the peripheral hardware units. Addresses 40H through 7FH overlap the data memory specified by the BANK register. In other words, addresses 40H through 7FH of the register file are addresses 40H through 7FH of the currently-selected bank of data memory. Addresses 40H through 7FH of the register file can be manipulated in the same manner as the data memory, except that the addresses of the register file can also be manipulated by using register file manipulation instructions ("PEEK WR, rf" and "POKE rf, WR"). Note, however, that addresses 40H through 6FH of BANK15 are assigned control register including port input/output selection registers (for details refer to 8.3 Control Registers and Input/Output Selection Registers). Addresses 5CH through 6FH of BANK14 are assigned LCD segment register (for details, refer to 8.4 LCD Segment Register). Figure 8-2. Configuration of Register File and Relationship with Data Memory Column address 0 0 1 1 2 3 4 5 6 7 8 9 A B C D E F Row address 2 3 4 5 6 7 BANK0 BANK1 BANK2 BANK3 BANK14 LCD segment register BANK15 (Control register) Port input/output selection registers System registers Data memory 0 1 2 3 Register file BANK15 (Control registers) Caution Remark Never write anything to address 31H of BANK15 because this address is a test mode area. Address 5BH is not provided to BANK4 through BANK14. 58 PD17933, 17934 8.2.1 Register file manipulation instructions ("PEEK WR, rf", "POKE rf, WR") Data is read from or written to the register file via the window register of the system registers, by using the following instructions. (1) "PEEK WR, rf" Reads data of the register file addressed by "rf" to the window register. (2) "POKE rf, WR" Writes the data of the window register to the register file addressed by "rf". 8.3 Control Registers and Input/Output Selection Registers Figure 8-3 shows the configuration of the control registers. The control registers, including the input/output select registers, consist of a total of 112 nibbles (112 x 4 bits) at addresses 00H through 6FH of BANK15 of the data memory. Of these addresses, 00H through 3FH overlap addresses 00H through 3FH of the register file. Addresses 60H through 6FH are assigned the input/output select registers. However, only 38 nibbles of the control registers are actually used. The remaining 14 nibbles are unused registers and prohibited from being written or read. Each control register has an attribute of 1 nibble that identifies four types of registers: read/write (R/W), readonly (R), write-only (W), and read-and-reset (R&Reset) registers. Nothing is changed even if data is written to a read-only (R and R&Reset) register. An "undefined" value is read if a write-only (W) register is read. Among the 4-bit data in 1 nibble, the bit fixed to "0" is always "0" when it is read, and is also "0" when it is written. The 74 nibbles of unused registers are undefined when their contents are read, and nothing changes even when they are written. Never write anything to address 31H of BANK15 because this address is a test mode area. Table 8-1 lists the peripheral hardware control functions of the control registers. 59 PD17933, 17934 Figure 8-3. Configuration of Control Registers (Addresses 00H-3FH) (1/4) (BANK15) Column Address Row Address Item 0 1 Stack pointer 2 Watchdog timer clock selection 3 Watchdog 4 Data buffer 5 Stack overflow/ 6 7 MOVT bit selection 0 (8)Note1 Name timer counter stack pointer underflow reset reset selection 0 0 0 D B F S P 1 D B F S P 0 0 0 S P R S E L 1 S P R S E L 0 Symbol SSSS PPPP 3210 00W D T C K 1 W D T C K 0 W00 D T R E S 0 0M O V T S E L 1 R/W M O V T S E L 0 ( ) ( ) ( ) ( ) ( ) ( ) Read/ Write 1 (9) Note1 R/W R/W W & Reset R R/W Name PLL mode selection PLL reference PLL unlock frequency selection FF BEEP clock selection Watchdog timer/stack pointer reset status detection Basic timer 0 carry Symbol P0PP0PPP00 LL L LLL LL L LLL MM S RRR DD C FFF 10 N CCC F KKK 210 R/W R/W 0P L L U L 0B E E P 0 S E L B E E P 0 C K 1 B E E P 0 C K 0 00 0W0 D T S P R E S 0 0B T M 0 C Y Read/ Write 2 (A) Note1 R & Reset R/W R & Reset R & Reset Name IF counter gate status detection IF counter mode selection IF counter control A/D converter A/D converter channel selection mode selection A0 D C C H 0 0A D C S T R T R A D C C M P Symbol 0 0 0F0 C G C H 0 Note 2 0 0 I F C G O S T T I F C M D 1 I F C M D 0 I F C C K 1 I0 F C C K 0 0 I F C S T R T W I0 F C R E S 0A D C C H 1 Read/ Write 3 (B) Note1 R R/W R/W R/W R/W Name Note 3 Symbol Read/ Write Notes 1. ( ) indicates an address that is used when the assembler is used. 2. Never write anything to address 20H of BANK15. 3. Never write anything to address 31H of BANK15 because this address is a test mode area. 60 PD17933, 17934 Figure 8-3. Configuration of Control Register (Address 00H-3FH) (2/4) 8 System register interrupt stack pointer 9 A B C D E F 0S Y S R S P 2 Basic timer 1 clock selection 0 00B T M 1 C K 0 R/W Note ( ) indicates an address that is used when the assembler is used. ( ) R ( S Y S R S P 1 ( S Y S R S P 0 ) ) Serial I/O1 clock Serial I/O1 mode selection 00S I O 1 C K 1 R/W S0SSS I III O OOO 1 111 C MHT K OIS 0 DZ R/W Interrupt edge selection 0 0 0 I E G 0 R/W Timer 0 counter clock selection T M 0 E N T M 0 R E S T M 0 C K 1 T M 0 C K 0 Timer 0 mode selection T0 M 0 O V F 0 0 I P S I O 1 I P S I O 0 I P T M 3 I P T M 2 I P T M 1 IIIIIII PPPPPPP T43210C E M 0 Interrupt enable 1 Interrupt enable 2 Interrupt enable 3 R/W R/W R/W R/W R/W Serial interface 1 Basic interval interrupt request 0 0 0 timer 1 interrupt request I0 R Q S I O 1 0 0 I0 R Q B T M 1 Timer 0 interrupt request 0 0 I R Q T M 0 INT0 pin interrupt request I0 N T 0 0 I R Q 1 R/W R/W R/W R/W 61 PD17933, 17934 Figure 8-3. Configuration of Control Register (Addresses 40H-6FH) (3/4) (BANK15) Column Address Row Address Item 0 LCD driver display start 1 2 3 4 5 6 7 4 Name Symbol L0 C D D B C K Note 0L C D E N Read/ Write 5 Name 1 R/W Symbol Read/ Write 6 Name Symbol Read/ Write Note Bit 3 of address 40H of BANK15 is a test mode area, therefore, do not write "1" to bit 3. 62 PD17933, 17934 Figure 8-3. Configuration of Control Register (Addresses 40H-6FH) (4/4) 8 9 A B C D E F LCD port selection Port 0D pull-down resistor Port 2C bit Port 2B bit Port 1D bit Port 1A bit Port 0B bit I/O selection I/O selection I/O selection I/O selection I/O selection 0 L C D 1 9 S E L L C D 1 8 S E L L C D 1 7 S E L P 0 D P L D 3 P 0 D P L D 2 P 0 D P L D 1 P 0 D P L D 0 P 2 C B I O 3 P 2 C B I O 2 P 2 C B I O 1 P 2 C B I O 0 P 2 B B I O 3 P 2 B B I O 2 P 2 B B I O 1 P 2 B B I O 0 P 1 D B I O 3 P 1 D B I O 2 P 1 D B I O 1 P 1 D B I O 0 P 1 A B I O 3 P 1 A B I O 2 P 1 A B I O 1 P 1 A B I O 0 P 0 B B I O 3 P 0 B B I O 2 P 0 B B I O 1 P 0 B B I O 0 R/W R/W R/W R/W R/W R/W R/W 63 PD17933, 17934 Table 8-1. Peripheral Hardware Control Functions of Control Registers (1/5) Peripheral Hardware Name Control Register Address Read/ b3 Peripheral Hardware Control Function Function Set value At Reset Reset by RESET WDT & SP reset F Clock Stop b2 (BANK15) Write Symbol b1 b0 Stack Stack pointer 01H R/W (SP3) (SP2) (SP1) (SP0) Interrupt stack pointer of system register 08H R 0 (SYSRSP2) (SYSRSP1) (SYSRSP0) Data buffer stack pointer 04H R 0 0 (DBFSP1) (DBFSP0) Stack overflow/ underflow reset selection 05H R/W 0 0 SPRSEL1 Selects interrupt stack overflow/underflow reset (can be set only once following power application) SPRSEL0 Selects address stack overflow/underflow reset (can be set only once following power application) Watchdog Watchdog timer timer clock selection 02H R/W 0 0 WDTCK1 WDTCK0 Watchdog timer counter reset 03H W& WDTRES 0 Not used set only once following power application) 0 Selects clock of watchdog timer (can be 0 1 pin F Retained 5 5 Retained Fixed to "0" 0 0 Retained Detects nesting level of data buffer stack Fixed to "0" 0 0 1 1 Level 0 Level 1 Level 2 Level 3 0 1 0 1 3 Retained Retained Reset prohibited Reset valid Fixed to "0" 3 Retained Retained 0 4096 instruction 1 1 Setting prohibited 0 1 8192 instruction 1 Undefined Undefined Resets watchdog timer counter Fixed to "0" Invalid Reset if written Undefined Reset 0 0 0 WDT&SP reset status detection 16H R& 0 0 1 Retained Reset 0 0 WDTSPRES Detects resetting of watchdog timer/stack pointer No reset request Reset request 64 PD17933, 17934 Table 8-1. Peripheral Hardware Control Functions of Control Registers (2/5) Peripheral Hardware Name Control Register Address Read/ b3 Peripheral Hardware Control Function Function Set value At Reset Reset by RESET WDT & SP reset 0 Clock Stop b2 (BANK15) Write Symbol b1 b0 MOVT MOVT bit selection 07H R/W 0 0 MOVTSEL1 Sets bit transferred by MOVT (transferred 16-bit MOVTSEL0 to 0EH and 0FH only during 8-bit transfer) 01 Serial Serial I/O1 1CH R/W 0 0 SIO0CK1 SIO0CK0 Sets internal clck of serial interface 1 Fixed to "0" transfer 00 0 Fixed to "0" 1 pin 0 Retained 0 High-order 8-bit transfer 1 1 Low-order 8-bit transfer 0 0 0 0 interface clock selection 0 External clock (75 kHz) 0 0 125 kHz 1 1 18.75 kHz 0 1 37.5 kHz 1 Serial I/O1 mode selection 1DH R/W 0 SIO1MOD SIO1HIZ Fixed to "0" Sets SI1/SO2 pin switching Sets P0B2/SO1 pin status SI1 General I/O port SO2 Serial data output pin 0 0 0 SIO1TS PLL frequency synthesizer Starts or stops operation Sets low-order bits of swallow counter Stops operation Starts operation LSB is 0 LSB is 1 Undefined Undefined PLL mode selection 10H R/W PLLSCNF 0 PLLMD1 PLLMD0 Retained Fixed to "0" Sets division mode of PLL 0 Disabled 0 0 MF 1 1 VHF 0 1 HF 1 0 0 0 PLL reference frequency selection 11H R/W 0 Fixed to "0" 1: 3 kHz 2: 5 kHz 3: 6.25 kHz 4: 12.5 kHz 5: 25 kHz 6: Setting prohibited 7: Setting prohibited 7 7 7 PLLRFCK2 Sets reference frequency of PLL 0: 1 kHz PLLRFCK1 PLLRFCK0 PLL unlcok FF 12H R& 0 Fixed to "0" Undefined Undefined Retained Reset 0 0 PLLUL BEEP BEEP/generalpurpose port pin function selection BEEP0CK1 Sets BEEP pin BEEP0CK0 Timer Basic timer 0 carry 17H R& 0 Fixed to "0" 14H R/W 0 Detects status of unlock FF Fixed to "0" BEEP Locked Unclocked 0 0 0 BEEP0SEL Selects function of P0B3/BEEP pin General-purpose I/O port 0 Low level output 0 0 1 1 High level 1.5 kHz 3 kHz output 1 0 1 0 Retained Retained Reset 0 0 BTM0CY Detects basic timer 0 carry FF FF reset FF set 65 PD17933, 17934 Table 8-1. Peripheral Hardware Control Functions of Control Registers (3/5) Peripheral Hardware Name Control Register Address Read/ b3 Peripheral Hardware Control Function Function Set value At Reset Reset by RESET WDT & SP reset 0 Clock Stop b2 (BANK15) Write Symbol b1 b0 Timer Basic timer 1 clock selection 18H R/W 0 0 0 BTM1CK0 Timer 0 counter 2BH clock selection R/W TM0EN TM0RES TM0CK1 TM0CK0 Timer 0 mode selection 2CH R/W TM0OVF TM0GCEG Selects clock of basic timer 0 Starts or stops timer 0 counter Resets timer 0 counter Sets basic clock of timer 0 counter Detects timer 0 overflow Sets edge of gate close input signal TM0GOEG Sets edge of gate open input signal TM0MD Selects modulo counter/gate counter of timer 0 Interrupt Interrupt edge selection 1FH R/W 0 0 0 IEG0 Sets interrupt issuance edge (INT pin) Interrupt enable 2FH R/W IPSIO1 Enables serial interface 1 interrupt IPBTM1 Enables basic interface timer 1 interrupt IPTM0 IP0 Serial interface 1 3CH interrupt request R/W 0 0 0 IRQSIO1 Detects serial interface 1 interrupt request Enables timer 0 interrupt Enables INT pin interrupt Fixed to "0" Fixed to "0" 0 TM0 0 0 Fixed to "0" 1 pin 0 Retained 31.25 Hz (32 ms) 125 Hz (8 ms) Stops Not affected 0 TM1 1 Starts Reset 1 75 kHz (13.3 s) 0 1 25 kHz (40 s) 1 0 0 0 No overflow Rising edge Overflow Falling edge 0 0 0 Modulo counter Gate counter 0 0 Retained Rising edge Falling edge Disables interrupt Enables interrupt 0 0 Retained 0 0 Retained No interrupt request Interrupt request 66 PD17933, 17934 Table 8-1. Peripheral Hardware Control Functions of Control Registers (4/5) Peripheral Hardware Name Control Register Address Read/ b3 Peripheral Hardware Control Function Function Set value At Reset Reset by RESET WDT & SP reset 0 Clock Stop b2 (BANK15) Write Symbol b1 b0 Interrupt Basic interval timer 1 interrupt request 3DH R/W 0 0 0 IRQBTM1 Detects basic interval timer 1 interrupt request Timer 0 interrupt request 3EH R/W 0 0 0 IRQTM0 INT0 pin interrupt request 3FH R/W INT0 0 0 IRQ0 IF counter 20H R/W 0 0 0 FCGCH0Note 1 IF counter gate status detection 21H R 0 0 0 IFCGOSTT Detects IF counter gate status IF counter mode selection 22H R/W IFCMD1 IFCMD0 IFCCK1 IFCCK0 IF counter control 23H W 0 0 IFCSTRT IFCRES A/D A/D converter 24H R/W 0 0 ADCCH1 ADCCH0 Selects pin used for A/D converter Starts or stops IF counter Resets IF counter data Fixed to "0" Fixed to "0" Sets IF counter gate time Sets IF counter mode Fixed to "0" Fixed to "0" Fixed to "0" 0 1 pin 0 Retained No interrupt request Interrupt request 0 0 Retained Detects timer 0 interrupt request No interrupt request Interrupt request Detects INT0 pin status Fixed to "0" Low level High level Undefined Undefined Undefined Retained 0 0 Detects INT0 pin interrupt request No interrupt request Interrupt request Fixed to "0" 0 0 0 Note 1 0 0 0 Closed 0 0 general- AMIFC purpose input port 0 1 0 1ms 0 0 4 ms 1 1 FMIFC Open 1 AMIFC2 0 0 0 0 1 8 ms 0 1 1 Open 1 0 0 0 Nothing affected Starts counter Nothing affected Resets counter 0 0 Retained converter channel selection 0: A/D converter not used 1: P0D1/AD0 pin 2: P0D2/AD1pin 3: P0D3/AD2 pin 67 PD17933, 17934 Table 8-1. Peripheral Hardware Control Functions of Control Registers (5/5) Peripheral Hardware Name Control Register Address Read/ b3 Peripheral Hardware Control Function Function Set value At Reset PowerON WDT & SP reset 0 Clock Stop b2 (BANK15) Write Symbol b1 b0 A/D A/D converter 25H R 0 0 ADCSTRT Detects operating status of A/D converter ADCCMP Detects comparison result of A/D converter LCD driver LCD driver display start 40H R/W LCDDBCKNote 2 0 0 LCDEN LCD port selection 69H R/W 0 LCD19SEL LCD18SEL LCD17SEL Input/ output port Port 0D pulldown resistor selection 6AH R/W P0DPLD3 P0DPLD2 P0DPLD1 P0DPLD0 Port 2C bit I/O selection 6BH R/W P2CBIO3 P2CBIO2 P2CBIO1 P2CBIO0 Port 2B bit I/O selection 6CH R/W P2BBIO3 P2BBIO2 P2BBIO1 P2BBIO0 Port 1D bit I/O selection 6DH R/W P1DBIO3 P1DBIO2 P1DBIO1 P1DBIO0 Port 1A bit I/O selection 6EH R/W P1ABIO3 P1ABIO2 P1ABIO1 P1ABIO0 Port 0B bit I/O selection 6FH R/W P0BBIO3 P0BBIO2 P0BBIO1 P0BBIO0 Fixed to "0" Fixed to "0" 0 1 reset 0 0 converter mode selection Conversion ends Converting VADCREF > VADCIN VADCREF < VADCIN Retained Note 2 0 0 0 Sets ON/OFF of all the LCD display Display OFF Display ON 0 0 0 0 Retained Fixed to "0" Selects function of P2A2/LCD19 pin Selects function of P2A2/LCD18 pin Selects function of P2A2/LCD17 pin Selects pull-down resistor of P0D3 pin Generalpurpose input port Pull-down LCD Segment 0 Pull-down 0 0 Retained Selects pull-down resistor of P0D2 pin resistor used resistor not used Selects pull-down resistor of P0D1 pin Selects pull-down resistor of P0D0 pin Selects I/O of port P2C3 Selects I/O of port P2C2 Selects I/O of port P2C1 Selects I/O of port P2C0 Selects I/O of port P2B3 Selects I/O of port P2B2 Selects I/O of port P2B1 Selects I/O of port P2B0 Selects I/O of port P1D3 Selects I/O of port P1D2 Selects I/O of port P1D1 Selects I/O of port P1D0 Selects I/O of port P1A3 Selects I/O of port P1A2 Selects I/O of port P1A1 Selects I/O of port P1A0 Selects I/O of port P0B3 Selects I/O of port P0B2 Selects I/O of port P0B1 Selects I/O of port P0B0 Input Output 0 0 Retained Input Output 0 0 Retained Input Output 0 0 Retained Input Output 0 0 Retained Input Output 0 0 Retained Notes 1. Never write anything to address 20H of BANK15. 2. Bit 3 of address 40H of BANK15 is a test mode area, therefore, do not write "1" to bit 3. 68 PD17933, 17934 8.4 LCD Segment Registers The LCD segment registers consist of a total of 20 nibbles (20 x 4 bits) of addresses 5CH through 6FH of BANK14 of the data memory. For details, refer to 19. LCD CONTROLLER/DRIVER. 8.5 Cautions on Using Control Register Keep in mind the following points (1) through (4) when using the write-only (W), read-only (R), and unused registers of the control registers (addresses 00H through 6FH of BANK15. (1) An "undefined value" is read if a write-only register is read. (2) Nothing is affected even if a read-only register is written. (3) An "undefined value" is read if an unused register is read. Nor is anything affected if this register is written. (4) Never write anything to address 31H of BANK15 because this address is a test mode area. 69 PD17933, 17934 9. DATA BUFFER (DBF) 9.1 Outline of Data Buffer Figure 9-1 outlines the data buffer. The data buffer is located on the data memory and has the following two functions. * Reads constant data on the program memory (table reference) * Transfers data with the peripheral hardware units Figure 9-1. Outline of Data Buffer Data buffer Data write (PUT) Table reference (MOVT) Data read (GET) Peripheral hardware Constant data Program memory 70 PD17933, 17934 9.2 Data Buffer 9.2.1 Configuration of data buffer Figure 9-2 shows the configuration of the data buffer. As shown in the figure, the data buffer consists of a total of 16 bits of addresses 0CH through 0FH of BANK 0 on the data memory. The 16-bit data is configured with bit 3 of address 0CH as the MSB and bit 0 of address 0FH as the LSB. Because the data buffer is located on the data memory, it can be manipulated by all data memory manipulation instructions. Figure 9-2. Configuration of Data Buffer Column address 0 0 1 1 2 3 4 5 6 7 8 9 A B C D E F Data buffer (DBF) Row address 2 3 4 5 6 7 BANK0 BANK1 BANK2 BANK3 Data memory BANK14 BANK15 System register Remark Address 5BH is not provided to BANK4 through BANK14. Data memory Address Bit 0CH 0DH 0EH 0FH b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 DBF3 DBF2 DBF1 DBF0 Data buffer Bit Signal Data M S B Data L S B 71 PD17933, 17934 9.2.2 Table reference instruction ("MOVT DBF, @AR") This instruction moves the contents of the program memory addressed by the contents of the address register to the data buffer. The number of bits transferred by the table reference instruction can be specified by MOVT selection register (address 07H) of the control registers. When 8-bit data is transferred, it is read to DBF1 and 0. When the table reference instruction is used, one stack level is used. All the addresses of the program memory can be referenced by the table reference instruction. 9.2.3 Peripheral hardware control instructions ("PUT" and "GET") The operations of the "PUT" and "GET" instructions are as follows: (1) GET DBF, p Reads the data of a peripheral register addressed by "p" to the data buffer. (2) PUT p, DBF Sets the data of the data buffer to a peripheral register addressed by "p". 9.3 Relationships between Peripheral Hardware and Data Buffer Table 9-1 shows the relationships between the peripheral hardware and the data buffer. 72 PD17933, 17934 MEMO 73 PD17933, 17934 Table 9-1. Relationships between Peripheral Hardware and Data Buffer (1/2) Peripheral Hardware Peripheral Register Transferring Data with Data Buffer Name Symbol Peripheral address Execution of PUT/GET instruction PUT/GET PUT/GET PUT/GET GET PUT/GET PUT/GET PUT/GET GET I/O bit Actual bit A/D converter Serial interface 1 Timer 0 A/D converter data register Presettable shift register 1 Timer 0 modulo register Timer 0 counter ADCR SIO1SFR TM0M TM0C AR DBFSTK PLLR IFC 02H 04H 1AH 1BH 40H 41H 42H 43H 8 8 8 8 16 16 16 16 8 8 8 8 16 16 16 16 Address register Data buffer stack PLL frequency synthesizer Note Address register DBF stack PLL data register IFC data register Frequency counter Note The programmable counter of the PLL frequency synthesizer is configured of 17 bits, of which the highorder 16 bits indicate the PLL data register (PLLR) and the low-order bits are allocated to the PLLSCNF flag (the third bit of address 10H). For details, refer to 16. PLL FREQUENCY SYNTHESIZER. 74 PD17933, 17934 Table 9-1. Relationships between Peripheral Hardware and Data Buffer (2/2) At Reset Reset by RESET pin WDT&SP reset Clock Stop Function 0 Undefined FF 0 0 Undefined Undefined 0 0 Undefined FF 0 0 Undefined Undefined 0 Retained Retained FF 0 Retained Retained Retained 0 Sets compare voltage VADCREF of A/D converter Sets serial-out data and reads serial-in data Sets modulo register value of timer 0 Reads count value of timer 0 counter Transfers data with address register Saves data of data buffer Sets division value (N value) of PLL Reads count value of frequency counter 75 PD17933, 17934 9.4 Cautions on Using Data Buffer Keep the following points in mind concerning the unused peripheral addresses, write-only peripheral register (PUT only), and read-only peripheral register (GET only) when transferring data with the peripheral hardware via data buffer. * An "undefined value" is read if a write-only register is read. * Nothing is affected even if a read-only register is written. * An "undefined value" is read if an unused address is read. Nor is anything affected if this address is written. 76 PD17933, 17934 10. DATA BUFFER STACK 10.1 Outline of Data Buffer Stack Figure 10-1 outlines the data buffer stack. As shown in the figure, the data buffer stack consists of a data buffer stack pointer and data buffer stack registers. The data buffer stack saves or restores the contents of the data buffer when the "PUT" or "GET" instruction is executed. Therefore, the contents of the data buffer can be saved by one instruction when an interrupt is accepted. Figure 10-1. Outline of Data Buffer Stack DBF Data buffer stack pointer Address specification Data buffer stack registers 10.2 Data Buffer Stack Register Figure 10-2 shows the configuration of the data buffer stack registers. As shown in the figure, the data buffer stack registers consist of four 16-bit registers. The contents of the data buffer are saved by executing the "PUT" instruction, and the saved data is restored by executing the "GET" instruction. The data buffer contents can be successively saved up to 4 levels. 77 PD17933, 17934 Figure 10-2. Configuration of Data Buffer Stack Register Data buffer DBF3 DBF2 DBF1 DBF0 Transfer data GET 16 bits PUT Name Symbol Address Bit Data Data buffer stack register DBFSTK 41H b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 Valid data Saves contents of data buffer up to 4 levels 78 PD17933, 17934 10.3 Data Buffer Stack Pointer The data buffer stack pointer detects the multiplexing level of the data buffer stack registers. When the "PUT" instruction is executed to the data buffer stack, the value of the data buffer stack pointer is incremented by one; when the "GET" instruction is executed, the value of the pointer is decremented by one. The data buffer stack pointer can be only read and cannot be written. The configuration and function of the data buffer stack pointer are illustrated below. Name Flag symbol b3 b2 b1 b0 Address Read/Write Data buffer stack pointer 0 0 D B F S P 1 D B F S P 0 04H R Detects multiplexing level of data buffer stack 0 0 1 1 0 1 0 1 Level 0 Level 1 Level 2 Level 3 Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 Clock stop Retained 79 PD17933, 17934 10.4 Operation of Data Buffer Stack Figure 10-3 shows the operation of the data buffer stack. As shown in the figure, when the PUT instruction is executed, the contents of the data buffer are transferred to a data buffer stack register specified by the stack pointer, and the stack pointer is incremented by one. When the GET instruction is executed, the contents of a data buffer stack register specified by the stack pointer are transferred to the data buffer, and the stack pointer is decremented by one. Therefore, note that the value of the stack pointer is set to 1 if data has been written once because its initial value is 0, and that the stack pointer is set to 0 when data has been written four times. Note that when writing (PUT) exceeding four levels, the first data are discarded. Figure 10-3. Operation of Data Buffer Stack (a) If writing does not exceed level 4 0 1 2 3 Undefined Undefined Undefined Undefined A Undefined Undefined Undefined A B Undefined Undefined A B Undefined Undefined A B Undefined Undefined VDD PUT PUT GET GET (b) If writing exceeds level 4 0 1 2 3 A Undefined Undefined Undefined A B Undefined Undefined A B C Undefined A B C D E B C D E B C D E B C D PUT PUT PUT PUT PUT GET GET 80 PD17933, 17934 10.5 Using Data Buffer Stack A program example is shown below. Example To save the contents of the data buffer and address register by using INT0 interrupt routine (the contents of the data buffer and address register are not automatically saved when an interrupt occurs). START: BR INITIAL ; Reset address ; Interrupt vector address NOP ; SI0 NOP ; Basic timer 1 NOP ; TM0 INTINT: PUT GET PUT ; DBFSTK, DBF ; ; DBF, AR ; DBFSTK, DBF ; ; INT pin interrupt vector address (0004H) Saves contents of DBF to first level of data buffer stack (DBFSTK) Transfers contents of address register (AR) to DBF Saves contents of AR to second level of data buffer stack Processing B ; INT interrupt processing GET DBF, DBFSTK ; Restores second level of data buffer stack to data buffer, PUT AR, DBF ; and restores contents of data buffer to address register GET DBF, DBFSTK ; Restores first level of data buffer stack to data buffer EI RETI INITIAL: SET1 IP0 EI LOOP: Processing A BR END LOOP 10.6 Cautions on Using Data Buffer Stack The contents of the data buffer stack are not automatically saved when an interrupt is accepted, and therefore, must be saved by software. Even when a bank of the data memory other than BANK0 is specified, the contents of the data buffer (existing in BANK0) can be saved or restored by using the "PUT" and "GET" instructions. 81 PD17933, 17934 11. GENERAL-PURPOSE PORT The general-purpose ports output high-level, low-level, or floating signals to external circuits, and read highlevel or low-level signals from external circuits. 11.1 Outline of General-purpose Port Table 11-1 shows the relationships between each port and port register. The general-prupose ports are classified into I/O, input, and output ports. The I/O ports can be set in the input or output mode in 1-bit (1-pin) units. The inut or output mode of each I/O port is specified by the port input/output selection registers (addresses 60H through 6FH) of BANK15. Table 11-1. Relationships between Port (Pin) and Port Register (1/2) Port No. Pin Symbol I/O Bank Data Setting Method Port register (data memory) Address Symbol Bit symbol (reserved word) b3 b2 b1 b0 I/O (bit I/O) 71H P0B b3 b2 b1 b0 Output 72H P0C b3 b2 b1 b0 Input 73H P0D b3 b2 b1 b0 - - P0A1 P0A0 P0B3 P0B2 P0B1 P0B0 P0C3 P0C2 P0C1 P0C0 P0D3 P0D2 P0D1 P0D0 Port 0A No pin No pin 19 18 P0A1 P0A0 P0B3 P0B2 P0B1 P0B0 P0C3 P0C2 P0C1 P0C0 P0D3 P0D2 P0D1 P0D0 Output BANK0 70H P0A Port 0B 31 30 29 28 Port 0C 67 66 65 64 Port 0D 78 77 76 75 82 PD17933, 17934 Table 11-1. Relationships between Port (Pin) and Port Register (2/2) Port No. Pin Symbol I/O Bank Data Setting Method Port register (data memory) Address Symbol Bit symbol (reserved word) b3 b2 b1 b0 Input 72H P1C b3 b2 b1 b0 I/O (bit I/O) 73H P1D b3 b2 b1 b0 Input BANK2 70H P2A b3 b2 b1 b0 I/O (bit I/O) 71H P2B b3 b2 b1 b0 I/O (bit I/O) 72H P2C b3 b2 b1 b0 - BANK3 | BANK15 Note 70H-73H - P1A3 P1A2 P1A1 P1A0 P1C3 P1C2 P1C1 P1C0 P1D3 P1D2 P1D1 P1D0 - P2A2 P2A1 P2A0 P2B3 P2B2 P2B1 P2B0 P2C3 P2C2 P2C1 P2C0 Port 1A 23 22 21 20 P1A3 P1A2 P1A1 P1A0 P1C3 P1C2 P1C1 P1C0 P1D3 P1D2 P1D1 P1D0 No pin I/O (bit I/O) BANK1 70H P1A Port 1C 4 3 2 1 Port 1D 27 26 25 24 Port 2A 63 62 61 Port 2B 17 16 15 14 Port 2C 74 73 72 71 - P2A2 P2A1 P2A0 P2B3 P2B2 P2B1 P2B0 P2C3 P2C2 P2C1 P2C0 No pin Fixed to 0 Note Address 5BH is not provided to BANK4 through BANK14. 83 PD17933, 17934 11.2 General-Purpose I/O Port (P0B, P1A, P1D, P2B, P2C) 11.2.1 Configuration of I/O port The following paragraphs (1) and (2) show the configuration of the I/O ports. (1) P0B (P0B3, P0B2, P0B1, P0B0) P2B (P2B3, P2B2, P2B1, P2B0) P2C (P2C3, P2C2, P2C1, P2C0) VDD I/O selection flag Output latch Write instruction Port register (1 bit) VDD 1 0 Read instruction 84 PD17933, 17934 (2) P1A (P1A3, P1A2, P1A1, P1A0) P1D (P1D3, P1D2, P1D1, P1D0) I/O selection flag Output latch Write instruction Port register (1 bit) VDD 1 0 Read instruction 11.2.2 Using I/O port The input or output mode of the I/O ports is set by I/O selection register P0B, P1A, P1D, P2B or P2C of the control registers. Because these are bit I/O ports, they can be set in the input or output mode in 1-bit units. Setting the output data of or reading the input data of a port is carried out by executing an instruction that writes data to or reads data from the port. 11.2.3 shows the configuration of the I/O selection register of each port. 11.2.4 and 11.2.5 describe how each port is used as an input or output port. 11.2.6 describes the reset status of the I/O ports. 85 PD17933, 17934 11.2.3 I/O port I/O selection register The following I/O selection registers of the I/O ports are available. * Port 0B bit I/O selection register * Port 1A bit I/O selection register * Port 1D bit I/O selection register * Port 2B bit I/O selection register * Port 2C bit I/O selection register Each I/O selection register sets the input or output mode of the corresponding port pin. The following paragraphs (1) through (5) descibe the configuration and functions of the above I/O selection registers. 86 PD17933, 17934 (1) Port 0B bit I/O selection register Name Flag symbol b3 b2 b1 b0 Port 0B bit I/O selection P 0 B B I P 0 B B I P 0 B B I P 0 B B I (BANK15) 6FH R/W Address Read/Write OO 3 2 OO 1 0 Sets input/output mode of port 0 1 Sets P0B0 pin in input mode Sets P0B0 pin in output mode Sets input/output mode of port 0 1 Sets P0B1 pin in input mode Sets P0B1 pin in output mode Sets input/output mode of port 0 1 Sets P0B2 pin in input mode Sets P0B2 pin in output mode Sets input/output mode of port 0 1 Sets P0B3 pin in input mode Sets P0B3 pin in output mode 0 0 0 0 0 0 At reset Reset by RESET pin WDT&SP reset 0 0 Clock stop Retained 87 PD17933, 17934 (2) Port 1A bit I/O selection register Name Flag symbol b3 b2 b1 b0 Address Read/Write Port 1A bit I/O selection P 1 A B I P 1 A B I P 1 A B I P 1 A B I (BANK15) 6EH R/W OO 3 2 OO 1 0 Sets input/output mode of port 0 1 Sets P1A0 pin in input mode Sets P1A0 pin in output mode Sets input/output mode of port 0 1 Sets P1A1 pin in input mode Sets P1A1 pin in output mode Sets input/output mode of port 0 1 Sets P1A2 pin in input mode Sets P1A2 pin in output mode Sets input/output mode of port 0 1 Sets P1A3 pin in input mode Sets P1A3 pin in output mode 0 0 0 0 0 0 At reset Reset by RESET pin WDT&SP reset 0 0 Clock stop Retained 88 PD17933, 17934 (3) Port 1D bit I/O selection register Name Flag symbol b3 b2 b1 b0 Port 1D bit I/O selection P 1 D B I P 1 D B I P 1 D B I P 1 D B I (BANK15) 6DH R/W Address Read/Write OO 3 2 OO 1 0 Sets input/output mode of port 0 1 Sets P1D0 pin in input mode Sets P1D0 pin in output mode Sets input/output mode of port 0 1 Sets P1D1 pin in input mode Sets P1D1 pin in output mode Sets input/output mode of port 0 1 Sets P1D2 pin in input mode Sets P1D2 pin in output mode Sets input/output mode of port 0 1 At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 0 0 Sets P1D3 pin in input mode Sets P1D3 pin in output mode Clock stop Retained 89 PD17933, 17934 (4) Port 2B bit I/O selection register Name Flag symbol b3 b2 b1 b0 Address Read/Write Port 2B bit I/O selection P 2 B B I P 2 B B I P 2 B B I P 2 B B I (BANK15) 6CH R/W OO 3 2 OO 1 0 Sets input/output mode of port 0 1 Sets P2B0 pin in input mode Sets P2B0 pin in output mode Sets input/output mode of port 0 1 Sets P2B1 pin in input mode Sets P2B1 pin in output mode Sets input/output mode of port 0 1 Sets P2B2 pin in input mode Sets P2B2 pin in output mode Sets input/output mode of port 0 1 At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 0 0 Sets P2B3 pin in input mode Sets P2B3 pin in output mode Clock stop Retained 90 PD17933, 17934 (5) Port 2C bit I/O selection register Name Flag symbol b3 b2 b1 b0 Address Read/Write Port 2C bit I/O selection P 2 C B I P 2 C B I P 2 C B I P 2 C B I (BANK15) 6BH R/W OO 3 2 OO 1 0 Sets input/output mode of port 0 1 Sets P2C0 pin in input mode Sets P2C0 pin in output mode Sets input/output mode of port 0 1 Sets P2C1 pin in input mode Sets P2C1 pin in output mode Sets input/output mode of port 0 1 Sets P2C2 pin in input mode Sets P2C2 pin in output mode Sets input/output mode of port 0 1 Sets P2C3 pin in input mode Sets P2C3 pin in output mode 0 0 0 0 0 0 At reset Reset by RESET pin WDT&SP reset 0 0 Clock stop Retained 91 PD17933, 17934 11.2.4 When using I/O port as input port The port pin to be set in the input mode is selected by the I/O selection register corresponding to the port. Ports P0B, P1A, P1D, P2B and P2C can be set in the input or output mode in 1-bit units. The pin set in the input mode is floated (Hi-Z) and waits for input of an external signal. The input data is read by executing a read instruction (such as SKT) to the port register corresponding to the port pin. "1" is read from the port register when a high level is input to the corresponding port pin; when a low level is input to the port pin, "0" is read from the register. When a write instruction (such as MOV) is executed to the port register corresponding to the pin set in the input mode, the contents of the output latch are rewritten. 11.2.5 When using I/O port as output port The port pin to be set in the output mode is selected by the I/O selection register corresponding to the port. Ports P0B, P1A, P1D, P2B and P2C can be set in the input or output mode in 1-bit units. The pin set in the output mode outputs the contents of the output latch. The output data is set by executing a write instruction (such as MOV) to the port register corresponding to the port pin. Write "1" to the port register to output a high level to the port pin; write "0" to output a low level. The port pin can be also floated (Hi-Z) if it is set in the input mode. If a read instruction (such as SKT) is executed to the port register corresponding to a port pin set in the output mode, the contents of the output latch are read. 11.2.6 Status of I/O port at reset (1) At reset by RESET pin All the I/O ports are set in the input mode. The contents of the output latch are reset to "0". (2) At WDT&SP reset All the I/O ports are set in the input mode. The contents of the output latch are reset to "0". (3) On execution of clock stop instruction The setting of the input or output mode is retained. The contents of the output latch are also retained. (4) In halt status The previous status is retained. 92 PD17933, 17934 11.3 General-Purpose Input Port (P0D, P1C, P2A) 11.3.1 Configuration of input port The following paragraphs (1) and (2) show the configuration of the input port. (1) P0D (P0D3, P0D2, P0D1, P0D0) To A/D converter Write instruction VDD Port register (1 bit) Read instruction High-ON resistance P0DPLD flag (2) P1C (P1C3, P1C2, P1C1, P1C0) P2A (P2A2, P2A1, P2A0) To frequency counter Write instruction VDD Port register (1 bit) Read instruction 93 PD17933, 17934 11.3.2 Using input port The input data is read by executing a read instruction (such as SKT) to the port register corresponding to the port pin. "1" is read from the port register when a high level is input to the corresponding port pin; when a low level is input to the port pin, "0" is read from the register. Nothing is affected even if a write instruction (such as MOV) is executed to the port register. P0D has a pull-down resistor that can be connected or disconnected by software in 1-bit units. The pull-down resistor is connected when "0" is written to the corresponding bit of the port 0D pull-down resistor selection register. When "1" is written to the corresponding bit of this register, the pull-down resistor is disconnected. 11.3.3 Port 0D pull-down resistor selection register The port 0D pull-down resistor selection register specifies whether a pull-down resistor is connected to P0D3 through P0D0 pins. The configuration and function of this register are illustrated below. * Port 0D pull-down resistor selection register Name Flag symbol b3 b2 b1 b0 Port 0D pull-down resistor selection P 0 D P L D 3 P 0 D P L D 2 P 0 D P L D 1 P 0 D P L D 0 (BANK15) 6AH R/W Address Read/Write Selects pull-down resistor of P0D0 pin 0 1 Connects pull-down resistor to P0D0 pin Disconnects pull-down resistor from P0D0 pin Selects pull-down resistor of P0D1 pin 0 1 Connects pull-down resistor to P0D1 pin Disconnects pull-down resistor from P0D1 pin Selects pull-down resistor of P0D2 pin 0 1 Connects pull-down resistor to P0D2 pin Disconnects pull-down resistor from P0D2 pin Selects pull-down resistor of P0D3 pin 0 1 At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 0 0 Connects pull-down resistor to P0D3 pin Disconnects pull-down resistor from P0D3 pin Clock stop Retained 94 PD17933, 17934 11.3.4 Status of input port at reset (1) At reset by RESET pin All the input ports are set in the input mode. All the pull-down resistors of P0D are connected. (2) At WDT&SP reset All the input ports are set in the input mode. All the pull-down resistors of P0D are connected. (3) On execution of clock stop instruction All the input ports are set in the input mode. The pull-down resistors of P0D retain the previous status. (4) In halt status The previous status is retained. 95 PD17933, 17934 11.4 General-Purpose Output Port (P0A, P0C) 11.4.1 Configuration of output port The configuration of the output port is shown below. (1) P0A (P0A1, P0A0) Output latch Write instruction Port register (1 bit) Read instruction (2) P0C (P0C3, P0C2, P0C1, P0C0) VDD Output latch Write instruction Port register (1 bit) Read instruction 11.4.2 Using output port The output port outputs the contents of the output latch to each pin. The output data is set by executing a write instruction (such as MOV) to the port register corresponding to the port pin. Write "1" to the port register to output a high level to the port pin; write "0" to output a low level. However, because P0A is an N-ch open-drain output port, it is floated when it outputs a high level. Therefore, an external pull-up resistor must be connected to this port. If a read instruction (such as SKT) is executed to the port register, the contents of the output latch are read. 11.4.3 Status of output port at reset (1) At reset by RESET pin The contents of the output latch are output. The contents of the output latch are reset to "0". 96 PD17933, 17934 (2) At WDT&SP reset The contents of the output latch are output. The contents of the output latch are reset to "0". (3) On execution of clock stop instruction The contents of the output latch are output. The contents of the output latch are retained. (4) In halt status The contents of the output latch are output. The contents of the output latch are retained. 97 PD17933, 17934 12. INTERRUPT 12.1 Outline of Interrupt Block Figure 12-1 outlines the interrupt block. As shown in the figure, the interrupt block temporarily stops the currently executed program and branches execution to a vector address in response to an interrupt request output by a peripheral hardware unit. The interrupt block consists of an "interrupt request servicing block" corresponding to each peripheral hardware unit, "interrupt enable flip-flop" that enables all interrupts, "stack pointer" that is controlled when an interrupt is accepted, "address stack registers", "program counter", and "interrupt stack". The "interrupt control block" of each peripheral hardware unit consists of an "interrupt request flag (IRQ xxx)" that detects the corresponding interrupt request, "interrupt enable flag (IPxxx)" that enables the interrupt, and "vector address generator (VAG)" that specifies a vector address when the interrupt is accepted. The PD17934 has the following three types of maskable interrupts. * INT interrupts * Timer 0 and basic interval timer 1 interrupts * Serial interface 1 interrupts When an interrupt is accepted, execution branches to a predetermined address, and the interrupt is serviced. 98 PD17933, 17934 Figure 12-1. Outline of Interrupt Block Interrupt control block IPSIO1 flag Serial interface 1 IRQSIO1 flag Vector address generator 01H Stack pointer Address stack registers Program counter IPBTM1 flag Basic timer 1 IRQBTM1 flag Vector address generator 02H System registers IPTM0 flag Timer 0 IRQTM0 flag Vector address generator 03H Pointer Interrupt stack IP flag INT pin IR flag Vector address generator 04H DI, EI instruction Interrupt enable flip-flop 99 PD17933, 17934 12.2 Interrupt Control Block An interrupt control block is provided for each peripheral hardware unit. This block detects issuance of an interrupt request, enables the interrupt, and generates a vector address when the interrupt is accepted. 12.2.1 Configuration and function of interrupt request flag (IRQxxx) Each interrupt request flag is set to 1 when an interrupt request is issued by the corresponding peripheral hardware unit, and is reset to 0 when the interrupt is accepted. Writing the interrupt request flag to "1" directly is equivalent to issuance of the interrupt request. By detecting the interrupt request flag when an interrupt is not enabled, issuance status of each interrupt request can be detected. Once the interrupt request flag has been set, it is not reset until the corresponding interrupt is accepted, or until "0" is written to the flag via a window register. Even if two or more interrupt requests are issued at the same time, the interrupt request flag corresponding to the interrupt that has not been accepted is not reset. Figures 12-2 through 12-15 show the configuration and function of the respective interrupt request registers. Figure 12-2. Configuration of Serial Interface 1 Interrupt Request Register Name Flag symbol b3 b2 b1 b0 Address Read/Write Serial interface 1 interrupt request 0 0 0 I R Q S I O 1 (BANK15) 3CH R/W Indicates interrupt request issuance status of serial interface 1 0 1 Interrupt request not issued Interrupt request issued Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 R Clock stop R: Retained 100 PD17933, 17934 Figure 12-3. Configuration of Basic Timer 1 Interrupt Request Register Name Flag symbol b3 b2 b1 b0 Address Read/Write Basic timer 1 interrupt request 0 0 0 I R Q B T M 1 (BANK15) 3DH R/W Indicates interrupt request issuance status of timer 2 0 1 Interrupt request not issued Interrupt request issued Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 R Clock stop R: Retained 101 PD17933, 17934 Figure 12-4. Configuration of Timer 0 Interrupt Request Register Name Flag symbol b3 b2 b1 b0 Address Read/Write Timer 0 interrupt request 0 0 0 I R Q T M 0 (BANK15) 3EH R/W Indicates interrupt request issuance status of timer 0 0 1 Interrupt request not issued Interrupt request issued Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 R Clock stop R: Retained 102 PD17933, 17934 Figure 12-5. Configuration of INT Pin Interrupt Request Register Name Flag symbol b3 b2 b1 b0 Address Read/Write INT pin interrupt request I N T 0 0 0 I R Q 0 (BANK15) 3FH R/W Indicates interrupt request issuance status of INT pin 0 1 Interrupt request not issued Interrupt request issued Fixed to "0" Detects status of INT pin 0 1 Low level is input High level is input 0 0 0 0 R At reset Reset by RESET pin WDT&SP reset U U U Clock stop U: Undefined, R: Retained 103 PD17933, 17934 12.2.2 Function and configuration of interrupt request flag (IPxxx) Each interrupt request flag enables the interrupt of the corresponding peripheral hardware unit. In order for an interrupt to be accepted, all the following conditions must be satisfied. * The interrupt must be enabled by the corresponding interrupt request flag. * The interrupt request must be issued by the corresponding interrupt request flag. * The EI instruction (which enables all interrupts) must be executed. The interrupt enable flags are located on the interrupt enable register on the register file. Figures 12-6 shows the configuration of each interrupt enable register. Figure 12-6. Configuration of Interrupt Enable Register Name Flag symbol b3 b2 b1 b0 Address Read/Write Interrupt enable I P S I I P B T I P T M 0 I P 0 (BANK15) 2FH R/W OM 1 1 Enables or disables INT pin interrupt 0 1 Disables Enables Enables or disables timer 0 interrupt 0 1 Disables Enables Enables or disables basic timer 1 interrupt 0 1 Disables Enables Enables or disables serial interface 1 interrupt 0 1 Disables Enables At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 0 0 Clock stop Retained 104 PD17933, 17934 12.2.3 Vector address generator (VAG) The vector address generator generates a branch address (vector address) of the program memory corresponding to an interrupt source that has been accepted from the corresponding peripheral hardware. Table 12-1 shows the vector addresses of the respective interrupt sources. Table 12-1. Interrupt Sources and Vector Addresses Interrupt Source INT pin Timer 0 Basic timer 1 Serial interface 1 Vector Address 0004H 0003H 0002H 0001H 105 PD17933, 17934 12.3 Interrupt Stack Register 12.3.1 Configuration and function of interrupt stack register Figure 12-7 shows the configuration of the interrupt stack register. The interrupt stack register saves the contents of the following system registers (except the address register (AR)) when an interrupt is accepted. * Window register (WR) * Bank register (BANK) * Index register (IX) * General pointer (RP) * Program status word (PSWORD) When an interrupt is accepted and the contents of the above system registers are saved to the interrupt stack, the contents of the above system registers, except the window register, are reset to "0". The interrupt stack can save the contents of the above system registers at up to four levels. Therefore, interrupts can be nested up to four levels. The contents of the interrupt stack register are restored to the system registers when the interrupt return (RETI) instruction is executed. The contents of the interrupt stack register are undefined at reset by RESET pin. The previous contents are retained on execution of the clock stop instruction. Figure 12-7. Configuration of Interrupt Stack Register Interrupt stack pointer of system register Interrupt stack register (INTSK) Name Window stack WRSK Bank stack BANKSK Index stack H IXHSK Index stack M IXHSK Index stack L IXHSK Bit b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 0H 1H 2H 3H 4H 5H Undefined INTSK1 INTSK2 INTSK3 INTSK4 Pointer stack H RPHSK Pointer stack L RPLSK Status stack PSWSK Bit b3 b2 b1 b0 0 S Y S R S P 2 S Y S S Y S Address RR S P 1 S P 0 Undefined 106 PD17933, 17934 12.3.2 Interrupt stack pointer of system register The interrupt stack pointer of the system register detects the nesting level of interrupts. The interrupt stack pointer can be only read and cannot be written. The configuration and function of the interrupt stack pointer are illustrated below. Name Flag symbol b3 b2 b1 b0 Address Read/Write ) ) ) Interrupt stack pointer of 0 system registers 08H R S Y S R S P 2 S Y S R S P 1 S Y S R S P 0 ( ( ( Detects level of interrupt stack of system registers 0 0 0 0 1 1 0 0 1 1 0 0 0 1 0 1 0 1 Use prohibited 4 levels (INTSK1) 3 levels (INTSK2) 2 levels (INTSK3) 1 level (INTSK4) 0 level Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 1 1 0 0 1 1 Clock stop Retained 107 PD17933, 17934 12.3.3 Interrupt stack operation Figure 12-8 shows the operation of the interrupt stack. When nested interrupts exceeding four levels are accepted, since the contents saved first are discarded they therefore must be saved by the program. Figure 12-8. Operation of Interrupt Stack (1/2) (a) Where interrupt nesting level is 4 or less Undefined Undefined Undefined Undefined Main routine MAIN Undefined Undefined Undefined Interrupt A A MAIN Undefined Undefined Interrupt B MAIN A B RETI RETI Undefined Undefined Undefined Undefined MAIN Undefined Undefined Undefined A MAIN Undefined Undefined 108 PD17933, 17934 Figure 12-8. Operation of Interrupt Stack (2/2) (b) Where interrupt nesting level is 5 or more Undefined Undefined MAIN Undefined Undefined Undefined A MAIN Undefined Undefined Interrupt C C B A MAIN Interrupt D D C B A Interrupt E Main routine Interrupt A MAIN A B D E Interrupt level 1 Interrupt level 2 Interrupt level 4 Interrupt level 5 System reset Caution The system is reset when an interrupt of level 5 is accepted. However, the ISPRES flag, which resets the non-maskable interrupt if the interrupt stack overflows or underflows, must be set to "1". This flag is "1" after system reset, and can then be written only once. 109 PD17933, 17934 12.4 Stack Pointer, Address Stack Registers, and Program Counter The address stack registers save a return address when execution returns from an interrupt routine. The stack pointer specifies the address of an address stack register. When an interrupt is accepted, the value of the stack pointer is decremented by one, and the value of the program counter at that time is saved to an address stack register specified by the stack pointer. Next, the interrupt routine is executed. When the interrupt return (RETI) instruction is executed after that, the contents of an address stack register specified by the stack pointer are restored to the program counter, and the value of the stack pointer is incremented by one. For further information, also refer to 3. ADDRESS STACK (ASK). 12.5 Interrupt Enable Flip-Flop (INTE) The interrupt enable flip-flop enables or disables the four types of maskable interrupts. When this flip-flop is set, all the interrupts are enabled. When it is reset, all the interrupts are disabled. This flip-flop is set or reset by dedicated instructions EI (to set) and DI (to reset). The EI instruction sets this flip-flop when the instruction next to EI is executed, and the DI instruction resets the flip-flop while it is being executed. When an interrupt is accepted, this flip-flop is automatically reset. This flip-flop is also reset at power-ON reset, at a reset by the RESET pin, at a watchdog timer, overflow or underflow of the stack. The flip-flop retains the previous status on execution of the clock stop instruction. 110 PD17933, 17934 12.6 Accepting Interrupt 12.6.1 Accepting interrupt and priority The following operations are performed before an interrupt is accepted. (1) Each peripheral hardware unit outputs an interrupt request signal to the corresponding interrupt request block if a given interrupt condition (for example, input of the falling signal to the INT pin) is satisfied. (2) When each interrupt request block accepts an interrupt request signal from the corresponding peripheral hardware unit, it sets the corresponding interrupt request flag (for example, IRQ0 flag if it is the INT pin that has issued the interrupt request) to "1". (3) The interrupt enable flag corresponding to each interrupt request flag (for example, IP0 flag if the interrupt request flag is IRQ0) is set to "1" when each interrupt request flag is set to "1", and each interrupt request block outputs "1". (4) The signal output by the interrupt request block is ORed with the output of the interrupt enable flip-flop, and an interrupt accept signal is output. This interrupt enable flip-flop is set to "1" by the EI instruction, and reset to "0" by the DI instruction. If "1" is output by each interrupt request processing block while the interrupt enable flip-flop is set to "1", the interrupt is accepted. As shown in Figure 12-1, the output of the interrupt enable flip-flop is input to each interrupt request block via an AND circuit when an interrupt is accepted. The signal input to each interrupt request block causes the interrupt request flag corresponding to each interrupt request flag to be reset to "0" and the vector address corresponding to each interrupt to be output. If the interrupt request block outputs "1" at this time, the interrupt accept signal is not transferred to the next stage. If two or more interrupt requests are issued at the same time, therefore, the interrupts are accepted according to the priority shown in Table 12-2. Unless the interrupt request enable flag is set to "1", the corresponding interrupt is not accepted. Therefore, by resetting the interrupt enable flag to "0", the interrupt with a high hardware priority can be disabled. Table 12-2. Interrupt Priority Interrupt Source INT pin Timer 0 Basic timer 1 Serial interface 1 Priority 1 2 3 4 111 PD17933, 17934 12.6.2 Timing chart when interrupt is accepted The timing charts in Figure 12-9 illustrate the operations performed when an interrupt or interrupts are accepted. Figure 12-9 (1) is the timing chart when one interrupt is accepted. (a) in (1) is the timing chart where the interrupt request flag is set to "1" after all the others, and (b) is the timing chart where the interrupt enable flag is set to "1" after all the others. In either case, the interrupt is accepted when the interrupt request flag, interrupt enable-flip flop, and interrupt enable flag all have been set to "1". If the flag or flip-flop that has been set last is set in the first instruction cycle of the "MOVT DBF, @AR" instruction or by an instruction that satisfies a given skip condition, the interrupt is accepted in the second instruction cycle of the "MOVT DBF, @AR" instruction or after the instruction that is skipped (this instruction is treated as NOP) has been executed. The interrupt enable flip-flop is set in the instruction cycle next to that in which the EI instruction is executed. Therefore, the interrupt is accepted after the instruction next to the EI instruction has been executed even when the interrupt request flag is set in the execution cycle of the EI instruction. (2) in Figure 12-9 is the timing chart where two or more interrupts are used. When two or more interrupts are used, the interrupts are accepted according to the hardware priority if all the interrupt enable flags are set. However, the hardware priority can be changed by setting the interrupt enable flags by the program. "Instruction cycle" shown in Figure 12-9 is a special cycle in which the interrupt request flag is reset, a vector address is specified, and the contents of the program counter are saved after an interrupt has been accepted. It takes 53.3 s, which is equivalent to one instruction execution time, to be completed. For details, refer to 12.7 Operations after Interrupt Has Been Accepted. 112 PD17933, 17934 Figure 12-9. Timing Charts When Interrupt Is Accepted (1/3) (1) When one interrupt (e.g., rising of INT pin) is used (a) If there is no interrupt mask time by the interrupt flag (IPxxx) <1> If a normal instruction which is not "MOVT" or an instruction that satisfies a skip condition is executed when interrupt is accepted Instruction EI MOV POKE WR, #0001B INTPM, WR Normal Interrupt instruction cycle INTE INT pin IRQ0 flag IP0 flag 1 instruction cycle 53.3 s INT pin interrupt accepted Interrupt enable period INT pin interrupt service <2> If "MOVT" or an instruction that satisfies a skip condition is executed when interrupt is accepted Instruction EI MOV POKE WR, #0001B INTPM, WR MOVT DBF, @AR or skip instruction Interrupt cycle INTE INT pin IRQ0 flag IP0 flag 1 instruction cycle 53.3 s INT pin interrupt accepted Interrupt enable period INT pin interrupt service 113 PD17933, 17934 Figure 12-9. Timing Charts When Interrupt Is Accepted (2/3) (b) If interrupt is kept pending by the interrupt enable flag Instruction EI MOV POKE WR, #0001B INTPM, WR Interrupt cycle INTE INT pin IRQ0 flag IP0 flag INT pin interrupt pending period INT pin interrupt service INT pin interrupt accepted (2) If two or more interrupts (e.g., INT pin and basic timer 1) are used (a) Hardware priority Instruction MOV POKE WR, #0101B INTPM, WR INTE INT pin IRQ0 flag Basic timer 1 IRQBTM1 flag IP0 flag IPBTM1 flag EI Interrupt cycle EI Interrupt cycle INT pin interrupt pending period INT pin interrupt service Basic timer 1 interrupt service Basic timer 1 interrupt pending period INT pin interrupt accepted Basic timer 1 pin interrupt accepted 114 PD17933, 17934 Figure 12-9. Timing Charts When Interrupt Is Accepted (3/3) (b) Software priority Instruction MOV POKE WR, #0100B INTPM, WR INTE INT pin IRQ0 flag Basic timer 1 IRQBTM1 flag IP0 flag IPBTM1 flag EI Interrupt MOV POKE cycle WR, #0101B INTPM, WR EI Interrupt cycle Basic timer 1 interrupt pending period Basic timer 1 pin interrupt service INT pin interrupt service INT pin interrupt pending period Basic timer 1 pin interrupt accepted INT pin interrupt accepted 115 PD17933, 17934 12.7 Operations after Interrupt Has Been Accepted When an interrupt is accepted, the following operations are sequentially performed automatically. (1) The interrupt enable flip-flop and the interrupt request flag corresponding to the accepted interrupt request are reset to "0". As a result, the other interrupts are disabled. (2) The contents of the stack pointer are decremented by one. (3) The contents of the program counter are saved to an address stack register specified by the stack pointer. At this time, the contents of the program counter are the program memory address after the address at which the interrupt has been accepted. For example, if a branch instruction is executed when the interrupt has been accepted, the contents of the program counter are the branch destination address. If a subroutine call instruction is executed, the contents of the program counter are the call destination address. If the skip condition of a skip instruction is satisfied, the next instruction is executed as NOP and then the interrupt is accepted. Consequently, the contents of the program counter are the address after that of the instruction that is skipped. (4) The contents of the system registers (except the address register) are saved to the interrupt stack. (5) The contents of the vector address generator corresponding to the interrupt that has been accepted are transferred to the program counter. In other words, execution branches to the interrupt routine. The operations (1) through (5) above require the time of one special instruction cycle (53.3 s) in which normal instruction execution is not performed. This instruction cycle is called an "interrupt cycle". In other words, the time of one instruction cycle (53.3 s) is required after an interrupt has been accepted until execution branches to the corresponding vector address. 12.8 Returning from Interrupt Routine The interrupt return (RETI) instruction is used to return from an interrupt routine to the processing during which an interrupt was accepted. When the RETI instruction is executed, the following operations are sequentially performed automatically. (1) The contents of an address stack register specified by the stack pointer are restored to the program counter. (2) The contents of the interrupt stack are restored to the system registers. (3) The contents of the stack pointer are incremented by one. The operations (1) through (3) above require one instruction cycle (53.3 s) in which the RETI instruction is executed. The only difference between the RETI instruction and the RET and RETSK instructions, which are subroutine return instructions, is the restoration of the bank register and index register in step (2) above. 116 PD17933, 17934 12.9 External Interrupts (INT pin) 12.9.1 Outline of external interrupts Figure 12-10 outlines the external interrupts. As shown in the figure, external interrupt requests are issued at the rising or falling edges of signals input to the INT pin. Whether an interrupt request is issued at the rising or falling edge of an INT pin is independently specified by the program. The INT pin is a Schmitt trigger input pin to prevent malfunctioning due to noise. This pin does not accept a pulse input of less than 100 ns. Figure 12-10. Outline of External Interrupts Interrupt control block INT0 flag IEG0 flag INT Schmitt trigger Edge detection block IRQ0 flag 117 PD17933, 17934 12.9.2 Edge detection block The edge detection block specifies the valid edge (rising or falling edge) of an input signal that issues the interrupt request of INT pin, by using an interrupt edge selection register. Figure 12-11 shows the configuration and function of the interrupt edge selection register. Figure 12-11. Configuration of Interrupt Edge Selection Register Name Flag symbol b3 b2 b1 b0 Address Read/Write Interrupt edge selection 1 0 0 0 I E G 0 (BANK15) 1FH R/W Selects input edge to issue interrupt request (INT3 pin) 0 1 Rising edge Falling edge Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 R Clock stop R: Retained Caution The external input delays about 100 ns. 118 PD17933, 17934 Table 12-3. Issuance of Interrupt Request by Changing IEG Flag Changes in IEG0 Flag 1 0 Status of INT Pin Low level High level Low level High level Issuance of Interrupt Request Not issued Issued Issued Not issued Status of Interrupt Request Flag Retains previous status Set to "1" Set to "1" Retains previous status (Falling) (Rising) 0 1 (Rising) (Falling) 12.9.3 Interrupt control block The signal levels that are input to the INT pin can be detected by using the INT0 flag. Because INT0 flag is reset independently of interrupts, when the interrupt function is not used the INT pin can be used as a 1-bit input port. If the interrupts are not enabled, these ports can be used as general-purpose port pins whose rising or falling edge can be detected by reading the corresponding interrupt request flags. At this time, however, the interrupt request flags are not automatically reset and must be reset by the program. For further information, also refer to 12.2.1 Configuration and function of interrupt request flag (IRQxxx). 12.10 Internal Interrupts The following three internal interrupts are available. * Timer 0 * Basic timer 1 * Serial interface 1 12.10.1 Timer 0 and basic timer 1 interrupts Interrupt requests are issued at fixed intervals. For details, refer to 13. TIMER. 12.10.2 Serial interface 1 interrupts Interrupt requests can be issued at the end of a serial output or serial input operation. For details, refer to 15. SERIAL INTERFACE. 119 PD17933, 17934 13. TIMERS Timers are used to manage the program execution time. 13.1 Outline of Timers Figure 13-1 outlines the timers. The following three timers are available. * Basic timer 0, 1 * Timer 0 Basic timer 0 and 1 detect the status of a flip-flop that is set at fixed time intervals in software. Timer 0 is a modulo timer and can use interrupts. The clock of each timer is created by dividing the system clock (75 kHz). Figure 13-1. Outline of Timers (1) Basic timer 0 75 kHz Clock selection Flip-flop BTM0CY flag (2) Basic timer 0 75 kHz Clock selection Interrupt control (3) Timer 0 4.5 MHz TM0 TM1 Start/stop Clock selection Coincidence detection Interrupt control 8-bit counter Modulo register 120 PD17933, 17934 13.2 Basic Timer 0 13.2.1 Outline of basic timer 0 Figure 13-2 outlines basic timer 0. Basic timer 0 is used as a timer by detecting in software the BTM0CY flag that is set at fixed intervals (125 ms). If the BTM0CY flag is read first after reset by RESET pin, "1" is always read. After that, the flag is set to "0" at 125 ms intervals. Figure 13-2. Outline of Basic Timer 0 75 kHz Divider 8 Hz 125 ms Flip-flop BTM0CY flag Remark BTM0CY (bit 0 of basic timer 0 carry register: refer to Figure 13-3) detects the status of the flipflop. 121 PD17933, 17934 13.2.2 Flip-flop and BTM0CY flag The flip-flop is set at fixed intervals (125 ms) and its status is detected by the BTM0CY flag of the basic timer 0 carry register. When the BTM0CY flag is read, it is reset to "0" (Read & Reset). The BTM0CY flag is always set to "1" at reset by RESET pin instruction. Figure 13-3 shows the configuration of the basic timer 0 carry register. Figure 13-3. Configuration of Basic Timer 0 Carry Register Name Flag symbol b3 b2 b1 b0 Address Read/Write Basic timer 0 carry 0 0 0 B T M 0 C Y (BANK15) 17H R & Reset Detects status of flip-flop 0 1 Flip-flop is not set Flip-flop is set Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 1 R R Clock stop R: Retained 122 PD17933, 17934 13.2.3 Example of using basic timer 0 An example of a program using basic timer 0 is shown below. This program executes processing A every 1 second. Example LOOP: SKT1 BR ADD SKE BR MOV BTM0CY NEXT M1, #1 M1, #08H NEXT M1, #0 ; Branches to NEXT if BTM0CY flag is "0" ; Adds 1 to M1 ; Executes processing A if M1 is "8" (1 second has elapsed) Processing A NEXT: Processing B BR LOOP ; Executes processing B and branches to LOOP 123 PD17933, 17934 13.2.4 Errors of basic timer 0 Errors of basic timer 0 include an error due to the detection time of the BTM0CY flag. Error due to detection time of BTM0CY flag The time to detect the BTM0CY flag must be shorter than the time at which the BTM0CY flag is set. Where the time interval at which the BTM0CY flag is detected is tCHECK and the time interval at which the flag is set is tSET (125 ms), tCHECK and tSET must relate as follows. tCHECK < tSET At this time, the error of the timer when the BTM0CY flag is detected is as follows, as shown in Figure 13-4. 0 < Error < tSET Figure 13-4. Error of Basic Timer 0 due to Detection Time of BTM0CY Flag BTM0CY flag setting pulse H L tSET 1 BTM0CY flag 0 tCHECK1 SKT1 BTM0CY <1> SKT1 BTM0CY <2> tCHECK2 SKT1 BTM0CY <3> tCHECK3 SKT1 BTM0CY <4> As shown in Figure 13-4, the timer is updated because BTM0CY flag is "1" when it is detected in step <2>. When the flag is detected next in step <3>, it is "0". Therefore, the timer is not updated until the flag is detected again in <4>. This means that the timer is extended by the time of tCHECK3. 124 PD17933, 17934 13.3 Basic Timer 1 13.3.1 General Figure 13-5 outlines the basic timer 1. The basic timer 1 issues an interrupt request at fixed time interval and sets the IRQBTM1 flag to 1. The time interval of the IRQBTM1 flag is set by the BTM1CK0 flag of the basic timer 1 clock select register. Figure 13-6 shows the configuration of the basic timer 1 clock select register. The interrupt generated by the basic timer 1 is accepted when the IRQBTM1 flag is set, if the EI instruction has been issued and the IPBTM1 flag has been set (refer to 12. INTERRUPT). Figure 13-5. Outline of Basic Timer 1 BTM1CK0 flag Internal signal 75 kHz (fixed) 32 ms (31.25 Hz) Divider 8 ms (125 Hz) Selector IRQBTM1 set signal Remark BTM1CK0 (bit 1 of interrupt edge select register. Refer to Figure 13-6) set the time interval at which the IRQBTM1 flag is set. 125 PD17933, 17934 13.3.2 Clock selection block The clock selection block divides the system clock (75 kHz) and sets the time interval at which the IRQBTM1 flag is to be set, by using the BTM1CK0 flags. Figure 13-6 shows the configuration of the basic timer 0 clock selection register. Figure 13-6. Configuration of Basic Timer 1 Clock Selection Register Name Flag symbol b3 b2 b1 b0 Address Read/Write Basic timer 1 clock selection 0 0 0 B T M 1 C K 0 (BANK15) 18H R/W Sets time interval at which IRQBTM1 flag is set 0 1 32 ms (31.25 Hz) 8 ms (125 Hz) Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 R Clock stop R : Retained 126 PD17933, 17934 13.3.3 Application example of basic timer 1 A program example is shown below. Example M1 MEM 0.10H 0002H START M1, #0001B CY EI_RETI M1, #0110B ; 80-ms counter ; Symbol definition of basic timer 1 interrupt vector address ; Branches to START ; Program address (0002H) ; Adds 1 to M1 ; Tests CY flag ; Returns if no carry BTIMER1 DAT BR ORG BTIMER1 ADD SKT1 BR MOV EI_RETI: EI RETI START: MOV BANK1 SET1 SET1 EI LOOP: BANK0 Processing A M1, #0110B BTM1CK IPBTM1 ; Initializes contents of M1 to 6 ; Embedded macro ; Sets basic timer 1 interrupt pulse to 8 ms ; Enables basic timer 1 interrupt ; Enables all interrupts Processing B BR LOOP This program executes processing A every 80 ms. The points to be noted in this case are that the DI status is automatically set when an interrupt has been accepted, and that the IRQBTM1 flag is set to 1 even in the DI status. This means that the interrupt is accepted even if execution exits from an interrupt service routine by execution of the "RETI" instruction, if processing A takes longer than 8 ms. Consequently, processing B is not executed. 127 PD17933, 17934 13.3.4 Error of basic timer 1 As described in 13.3.3, the interrupt generated by basic timer 1 is accepted each time the basic timer 1 interrupt pulse falls, if the EI instruction has been executed, and if the interrupt has been enabled. Therefore, an error of basic timer 1 occurs only when any of the following operations are performed: * When the first interrupt after basic timer 1 interrupt has been enabled has been accepted * When the time interval at which the IRQBTM1 flag is to be set is changed, i.e., when the first interrupt is accepted after the interrupt pulse has been changed * When data has been written to the IRQBTM1 flag Figure 13-7 shows an error in each of the above operations. Figure 13-7. Error of Basic Timer 1 (1/2) (a) When interrupt by basic timer 1 is enabled Basic timer 1 interrupt pulse IRQBTM1 flag IPBTM1 flag INTE FF H L 1 0 1 0 EI DI EI Interrupt pending tSET EI EI <1> <2> SET1 IPBTM1 Interrupt accepted <3> Interrupt accepted Interrupt accepted At point <1> in the above figure, the interrupt by basic timer 1 is accepted as soon as the interrupt is enabled. At this time, the error is -tSET. If an interrupt is enabled by the "EI" instruction at the next point <3>, the interrupt occurs at the falling edge of the basic timer 1 interrupt pulse. At this time, the error is: -tSET < error < 0 128 PD17933, 17934 Figure 13-7. Error of Basic Timer 1 (2/2) (b) When basic timer 1 interrupt pulse is changed Internal pulse A Internal pulse B Basic timer 1 interrupt pulse IRQBTM1 flag IPBTM1 flag INTE FF H L H L H L 1 0 1 0 EI DI EI EI <3> Basic timer 1 interrupt EI EI <1> Basic timer 1 interrupt pulse changed pulse changed Interrupt accepted Interrupt accepted <2> Interrupt accepted Even if the basic timer 1 interrupt pulse is changed to B at point <1> in the above figure, the interrupt is accepted at the next point <2> because the basic timer 1 interrupt pulse does not fall. If the basic timer 1 interrupt pulse is changed to A at <3>, the interrupt is immediately accepted because the basic timer 1 interrupt pulse falls. (c) When IRQBTM1 flag is manipulated Basic timer 1 interrupt pulse IRQBTM1 flag IPBTM1 flag INTE FF H L 1 0 1 0 EI DI EI Interrupt accepted EI <1> SET1 IRQBTM1 <2> CLR1 IRQBTM1 Interrupt accepted Interrupt not accepted EI Interrupt accepted The interrupt is immediately accepted if the IRQBTM1 flag is set to 1 at <1>. If clearing the IRQBTM1 flag to 0 overlaps with the falling of the basic timer 1 interrupt pulse at <2>, the interrupt is not accepted. 129 PD17933, 17934 13.3.5 Notes on using basic timer 1 When creating a program, such as a program for watch, in which processing is always performed at fixed time intervals by using the basic timer 1 after the supply voltage has been once applied (power-ON reset), the basic timer 1 interrupt service must be completed in a fixed time. Let's take the following example: Example M1 MEM 0.10H 0002H START M1, #0001B CY EI_RETI M1, #0110B ; 80-ms counter ; Symbol definition of interrupt vector address of basic timer 1 ; Branches to START ; Program address (0002H) ; Adds 1 to M1 ; Watch processing if carry occurs ; Restores if no carry occurs BTIMER1 DAT BR ORG BTIMER1 ADD SKT1 BR MOV ; <1> Processing B EI_RETI: EI RETI START: MOV BANK1 SET1 BTM1CK ; Embedded macro ; Sets time of interrupt by basic timer 1 to 8 ms SET1 EI LOOP: Processing A BR LOOP IPBTM1 ; Embedded macro ; Enables interrupt by basic timer 1 ; Enables all interrupts M1, #0110B ; Initializes contetns of M1 to 6 In this example, processing B is executed every 80 ms while processing A is executed. 130 PD17933, 17934 13.4 Timer 0 13.4.1 Outline of timer 0 Figure 13-8 outlines timer 0. Timer 0 counts the basic clock (75, 25, or external clock (TM0, TM1)) with an 8-bit counter, and compares the count value with a value set in advance. Figure 13-8. Outline of Timer 0 TM0CK1 flag TM0CK0 flag Interrupt control DBF 75 kHz TM0/P1C0 TM1/P1C1 Start/stop Clock selection TM0EN flag Timre 1 counter (TM0C) TM0RES flag Coincidence detection circuit Timer 0 IRQTM0 flag Timer 0 modulo register (TM0M) DBF Remarks 1. TM0CK1 and TM0CK0 (bits 1 and 0 of timer 0 counter clock selection register: refer to Figure 13-9) set the basic clock frequency. 2. TM0EN (bit 3 of timer 0 counter clock selection register: refer to Figure 13-9) starts or stops timer 0. 3. TM0RES (bit 2 of timer 0 counter clock selection register: refer to Figure 13-9) resets timer 0 counter. 131 PD17933, 17934 13.4.2 Clock selection and start/stop control blocks The clock selection block selects a basic clock to operate timer 0 counter. Four types of basic clocks can be selected by using the TM0CK1 and TM0CK0 flags. The start/stop block starts or stops the basic clock input to timer 0 by using the TM0EN flag. Figure 13-9 shows the configuration and function of each flag. 13.4.3 Count block The count block counts the basic clock with timer 0 counter, reads the count value, and issues an interrupt request when its count value coincides with the value of the timer 0 modulo register. The timer 0 counter can be reset by the TM0RES flag. The timer 0 counter is automatically reset when its value coincides with the value of the timer 0 modulo register. The value of the timer 0 counter can be read via data buffer. Data can be written to the value of the timer 0 modulo register via data buffer. Figure 13-9 shows the configuration of timer 0 counter clock selection register. Figure 13-10 shows the configuration of the timer 0 counter. Figure 13-11 shows the configuration of the timer 0 modulo register. 132 PD17933, 17934 Figure 13-9. Configuration of Timer 0 Counter Clock Selection Register Name Flag symbol b3 b2 b1 b0 Address Read/Write Timer 0 counter clock selection T T T T (BANK15) 2BH R/W MM 0 E N 0 R E S MM 0 C K 1 0 C K 0 Sets basic clock of timer 0 counter 0 0 1 1 0 1 0 1 TM0 TM1 75 kHz (13.3 s) 25 kHz (40 s) Resets timer 0 counter (valid on writing) 0 1 Does not change Resets counter Starts or stops timer 0 0 1 Stops Starts At reset Reset by RESET pin WDT&SP reset 0 0 0 0 Clock stop Caution When the TM0RES flag is read, 0 is always read. 133 PD17933, 17934 Figure 13-10. Configuration of Timer 0 Counter Data buffer DBF3 Don't care DBF2 Don't care Transfer data GET 8 bits PUT must not be executed Name Symbol Address Bit Data Valid data Timer 0 counter TM0C 1BH b7 b6 b5 b4 b3 b2 b1 b0 DBF1 DBF0 Reads count value of timer 0 0 x Count value 0FFH At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Clock stop 134 PD17933, 17934 Figure 13-11. Configuration of Timer 0 Modulo Register Data buffer DBF3 Don't care DBF2 Don't care Transfer data GET 8 bits PUT Name Symbol Address Bit Data Valid data Timer 0 modulo register TM0M 1AH b7 b6 b5 b4 b3 b2 b1 b0 DBF1 DBF0 Sets modulo data of timer 0 0 1 Setting prohibited x Modulo counter value 0FFH At reset Reset by RESET pin WDT&SP reset 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Clock stop 135 PD17933, 17934 13.4.4 Example of using timer 0 (1) Modulo timer The modulo timer is used for time management by generating timer 0 interrupt at fixed intervals. An example of a program is shown below. This program executes processing B every 400 s. TM0DATA START: BR INITIAL ; Interrupt vector address NOP NOP BR INT_TM0 NOP INITIAL: INITFLG ; MOV MOV PUT SET1 SET1 EI LOOP: Processing A BR INT_TM0: PUT DBFSTK, DBF ; Saves data buffer LOOP NOT TM0EN, TM0RES, TM0CK1, TM0CK0 (Stop) , (Reset) , (Basic clock = 40 s) DBF0, #TM0DATA DBF1, #TM0DATA SHR4 AND 0FH TM0, DBF TM0EN ; START IPTM0 ; Enables timer 0 interrupt ; Reset address ; ; ; ; SIO1 BTM1 TM0 INT DAT 0009H ; Count data = 10 Processing B GET EI RETI END DBF, DBFSTK ; Return 136 PD17933, 17934 13.4.5 Error of timer 0 Timer 0 has an error of up to 1 basic clock in the following cases. (1) On starting/stopping counter The counter is started or stopped by setting the TM0EN flag. Therefore, an error of 0 to +1 clocks occurs when the TM0EN flag is set, and an error of -1 to 0 clocks occurs when the flag is reset. In all, an error of 1 count occurs. (2) On resetting counter operation An error of 0 to +1 clocks occurs when the counter is reset. (3) On selecting basic clock during counter operation An error of 0 to +1 clocks of the newly selected clock occurs. 137 PD17933, 17934 14. A/D CONVERTER 14.1 Outline of A/D Converter Figure 14-1 outlines the A/D converter. The A/D converter compares the analog voltages input to the AD2 through AD0 pins with the internal compare voltage and converts them into 4-bit digital signals by judging the result of the comparison by software. The result of the comparison is detected by the ADCCMP flag. This converter is of successive approximation type. Figure 14-1. Outline of A/D Converter ADCCH1 flag ADCCH0 flag P0D3/AD2 P0D2/AD1 P0D1/AD0 Compare block DBF ADCSTRT flag ADCCMP flag Input selection block Compare voltage generation block R-string D/A converter Start/stop control block Remarks 1. ADCCH1 and ADCCH0 (bits 1 and 0 of A/D converter channel selection register: refer to Figure 14-3) select pins used for the A/D converter. 2. ADCCMP (bit 0 of A/D converter mode selection register: refer to Figure 14-5) detects the result of comparison. 3. ADCSTRT (bit 1 of A/D converter mode selection register: refer to Figure 14-5) detects the operating status. 138 PD17933, 17934 14.2 Input Selection Block Figure 14-2 shows the configuration of the input selection block. The input selection block selects a pin to be used by using the ADCCH1 and ADCCH0 flags. Only one pin can be used for the A/D converter. When one of the P0D1/AD0 through P0D3/AD2 pins is selected, the other two pins are forcibly set in the input port mode. The P0D1/AD0 through P0D3/AD2 pins can be connected to a pull-down resistor if so specified by the P0DPL1 through P0DPLD3 flags. To use the P0D1/AD0 through P0D3/AD2 pins for the A/D converter, therefore, disconnect their pull-down resistors to correctly detect an external input analog voltage. (For details, refer to 11.3.3 Port 0D pull-down resistor selection register.) Figure 14-3 shows the configuration of the A/D converter channel selection register. Figure 14-2. Configuration of Input Selection Block ADCCH1 ADCCH0 Selector P0D3/AD2 P0D2/AD1 P0D1/AD0 Compare block VADCIN Each input port 139 PD17933, 17934 Figure 14-3. Configuration of A/D Converter Channel Selection Register Name Flag symbol b3 b2 b1 b0 Address Read/Write A/D converter channel selection 0 0 A D C C H 1 A D C C H 0 (BANK15) 24H R/W Selects pin used for A/D converter 0 0 1 1 0 1 0 1 A/D converter not used (general-purpose input port) P0D1/AD0 pin P0D2/AD1 pin P0D3/AD2 pin Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 0 Clock stop Retained 140 PD17933, 17934 14.3 Compare Voltage Generation and Compare Blocks Figure 14-4 shows the configuration of the compare voltage generation block and compare block. The compare voltage generation block switches a tap decoder according to the 8-bit data set to the A/D converter reference voltage setting register and generates 256 different of compare voltages V ADCREF. In other words, this block is an R-string D/A converter. The supply voltage to this R-string D/A converter is the same as the supply voltage VDD of the device. The compare block compares voltage VADCIN input from a pin with compare voltage VADCREF. Comparison by the comparator is performed as soon as data has been written to the ADCSTRT flag. It takes the A/D converter the time of executing two instructions (106.6 s) to perform comparison once. The current operating status of the comparator can be checked by reading the content of the ADCSTRT flag. The result of the comparison is detected by the ADCCMP flag. Figure 14-5 shows the configuration of A/D converter mode selection register. Figure 14-4. Configuration of Compare Voltage Generation and Compare Blocks 1/2 VDD VADCIN DBF VADCREF 2 pF - Comparator + ADCCMP flag A/D converter reference voltage setting register (ADCR) Tap decoder 0 1 2 254 255 VDD 1 R 2 R R 3 R 2 Start/stop control block ADCSTRT flag 141 PD17933, 17934 Figure 14-5. Configuration of A/D Converter Mode Selection Register Name Flag symbol b3 b2 b1 b0 Address Read/Write A/D converter mode selection 0 0 A D C S T R T A D C C M P (BANK15) 25H R/W Detects result of comparison by A/D converter 0 1 VADCIN < VADCREF VADCIN > VADCREF Detects operating status of A/D converter 0 1 End of conversion Conversion in progress Fixed to "0" At reset Reset by RESET pin WDT&SP reser 0 0 0 0 0 0 0 R Clock stop R:Retained 142 PD17933, 17934 14.4 Comparison Timing Chart The ADCSTRT flag is reset to 0 two instructions after the ADCSTRT flag has been set. At this point, the compare result (ADCCMP flag) can be read. Figure 14-6 shows the timing chart. Figure 14-6. Timing Chart of A/D Converter's Compare Operation Instruction cycle A/D A/D converter start converter start instruction instruction NOP NOP ADCCMP read Sample & hold ADCSTRT flag ADCCMP flag Comparison result 143 PD17933, 17934 14.5 Using A/D Converter 14.5.1 Comparing with one compare voltage An example of a program in this mode is shown below. Example To compare input voltage VADCIN of AD0 pin with compare voltage VADCREF (127.5/256 VDD), and branch to AAA if VADCIN < VADCREF, or to BBB if VADCIN > VADCREF ADCR7 ADCR6 ADCR5 ADCR4 ADCR3 ADCR2 ADCR1 ADCR0 BANK15 INITFLG BANK0 INITFLG INITFLG INITFLG PUT SET1 NOP NOP SKT1 BR BR FLG FLG FLG FLG FLG FLG FLG FLG 0.0EH.3 ; Defines each bit of DBF as ADCR data setting flag. 0.0EH.2 0.0EH.1 0.0EH.0 0.0FH.3 0.0FH.2 0.0FH.1 0.0FH.0 NOT P0DPLD3, NOT P0DPLD2, P0DPLD1, NOT P0DPLD0 NOT ADCCH1, ADCCH0 ADCR7, NOT ADCR6, NOT ADCR5, NOT ADCR4 NOT ADCR3, NOT ADCR2, NOT ADCR1, NOT ADCR0 ADCR, DBF ADCSTRT ; Disconnects pull-down resistor of P0D1 pin. ; ; ; ; ; ; ; ; Selects AD0 pin for A/D converter. Sets compare voltage VADCREF. Starts A/D conversion. Waits for duration of two instructions. Judges result of comparison. ADCCMP AAA BBB 144 PD17933, 17934 14.5.2 Successive comparison by means of binary search The A/D converter can compare only one compare voltage at a time. Consequently, successive comparison must be executed through program in order to convert input voltages into digital signals. If the processing time of the successive comparison program is different depending on the input voltage, it is not desirable because of the relations with the other programs. Therefore, the binary search method described in (1) through (3) below is useful. (1) Concept of binary search The following figure illustrates the concept of binary search. First, the compare voltage is set to 1/2VDD. If the result of comparison is True (high level), a voltage of 1/4VDD is applied; if the result is False (low level), a voltage of 1/4VDD is subtracted for comparison. Similarly, comparison is performed in sequence from 1/8VDD to 1/16VDD. If the result is False after comparison has been executed four times, 1/16VDD is subtracted, and the comparison ends. 1 H H 7/8 L H 3/4 H L Compare voltage (xVDD) 5/8 L 1/2 H H 3/8 L L 1/4 H L 1/8 L 0 1/16 L 3/16 L 5/16 L 7/16 L 9/16 L 11/16 L 13/16 L 15/16 L 1 15/16 14/16 13/16 12/16 11/16 10/16 9/16 8/16 7/16 6/16 5/16 4/16 3/16 2/16 1/16 0/16 First Second Third Fourth Subtract 1/16 if false 145 PD17933, 17934 (2) Flowchart of binary search START Initial setting (A/D converter reference voltage setting register) = #1000B ADCCMP = 1? N Reset ADCRFSEL3 flag Set ADCRFSEL2 flag ADCCMP = 1? N Reset ADCRFSEL2 flag Set ADCRFSEL1 flag ADCCMP = 1? N Reset ADCRFSEL1 flag Set ADCRFSEL0 flag ADCCMP = 1? N Reset ADCRFSEL0 flag : if "0", subtract 1/16VDD and, Y : if "0", subtract 1/8VDD and, : add both "0" and "1" to 1/16VDD and set compare voltage. : Detect compare voltage and, Y : if "0", subtract 1/4VDD and, : add both "0" and "1" to 1/8VDD and set compare voltage. : Detect result of comparison and, Y : if "0", subtract 1/2VDD and, : add both "0" and "1" to 1/4VDD and set compare voltage. : Detect compare voltage and, Y : Select pin to be used. : Set compare voltage to 1/2VDD. : Detect result of comparison and, Detect content of A/D converter reference voltage setting register END : if "1", conversion ends. 146 PD17933, 17934 (3) Program example of binary search START: BANK1 INITFLG INITFLG INITFLG SET1 NOP NOP SKF1 SET1 CLR1 SET1 NOP NOP SKF1 SET1 CLR1 SET1 NOP NOP SKF1 SET1 CLR1 SET1 NOP NOP SKF1 SET1 ADCCMP ADCRFSEL0 ADCCMP ADCRFSEL1 ADCRFSEL0 ADCSTRT ADCCMP ADCRFSEL2 ADCRFSEL1 ADCSTRT ADCCMP ADCRFSEL3 ADCRFSEL2 ADCSTRT NOT ADCCH1, ADCCH0 P0DPLD1 NOT ADCRFSEL3, ADCRFSEL2, ADCRFSEL1, ADRFSEL0 ADCSTRT ; Selects AD0 pin. ; Sets pull-down resistor of AD0 pin OFF. ; Sets compare voltage to 7.5/16 VDD. ; A/D comparator starts operating. ; 2 wait ; ; Detects ADCCMP. ; If 0, adds 7.5/16 VDD and, ; subtracts 3.5/16 VDD. ; A/D comparator starts operating. ; 2 wait ; ; Detects ADCCMP. ; If 0, adds 3.5/16 VDD and, ; subtracts 1.5/16 VDD. ; A/D comparator starts operating. ; 2 wait ; ; Detects ADCCMP. ; If 0, adds 1.5/16 VDD and, ; subtracts 0.5/16 VDD. ; A/D comparator starts operating. ; 2 wait ; ; Detects ADCCMP. ; If 0, adds 0.5/16 VDD. END: 147 PD17933, 17934 14.6 Cautions on Using A/D Converter 14.6.1 Cautions on selecting A/D converter pin When one of the P0D1/AD0 through P0D3/AD2 pins is selected, the other two pins are forcibly set in the input port mode. The P0D1/AD0 through P0D3/AD2 pins can be connected to a pull-down resistor if so specified by the P0DPL1 through P0DPLD3 flags in bank 15. To use the P0D1/AD0 through P0D3/AD2 pins for the A/D converter, therefore, disconnect their pull-down resistors to correctly detect an external input analog voltage. 14.7 Status at Reset 14.7.1 At reset by RESET pin All the P0D1/AD0 through P0D3/AD2 pins are set in the general-purpose input port mode. The P0D1 through P0D3 pins are connected with a pull-down resistor. 14.7.2 At WDT&SP reset All the P0D1/AD0 through P0D3/AD2 pins are set in the general-purpose input port mode. The P0D1 through P0D3 pins are connected with a pull-down resistor. 14.7.3 On execution of clock stop instruction The status of the pin selected for the A/D converter is retained as is. The previous status of the pull-down resistor of the P0D1 through P0D3 pins is retained. 14.7.4 In halt status The status of the pin selected for the A/D converter is retained as is. The previous status of the pull-down resistor of the P0D1 through P0D3 pins is retained. 148 PD17933, 17934 15. SERIAL INTERFACE 15.1 General Figure 15-1 shows the outline of the serial interface. This serial interface is of two-wire/three-wire serial I/O type. The former type uses SCK and SO2/SI1 pins. The latter uses SCK, SI1, and SO1 pins. Figure 15-1. Outline of Serial Interface SIO1CK1, 0 flags Wait signal Clock I/O control block SIO1TS flag Clock control block 75 kHz Wait control block SCK/P0B0 Clock counter Count value 8 SIO1HIZ flag SIO1MOD flag IRQSIO flag Presettable shift register SO2/SI1/P0B1 Data I/O control block SO1/P0B2 OUT (SIO1SFR) IN Remarks 1. SIO1CK1 and 0 (bits 0 and 1 of serial I/O clock select register. Refer to Figure 15-2) set a shift clock. 2. SIO1TS (bit 0 of serial I/O mode select register. Refer to Figure 15-3) starts/stops communication. 3. SIO1HIZ (bit 1 of serial I/O mode select register. Refer to Figure 15-3) sets the function of the SO1/P0B2 pin. 4. SIO1MOD (bit 3 of serial I/O mode select register. Refer to Figure 15-3) selects I/O of SO2/ SI1/P0B1 pin. 149 PD17933, 17934 15.2 Clock Input/Output Control Block and Data Input/Output Control Block The clock input/output control block and data input/output control block select the operation mode of the serial interface (2-wire or 3-wire mode), control the transmit/receive operation, and select a shift clock. The flags that control these blocks are allocated to the serial I/O clock select register and serial I/O mode select register. Figure 15-2 shows the configuration and function of the serial I/O clock select register. Figure 15-3 shows the configuration and function of the serial I/O mode select register. Table 15-1 shows the setting status of each pin by the corresponding control flags. As shown in this table, the input/output setting flag of each pin must be also manipulated in addition to the control flag of the serial interface, to set each pin. The SIO1CK1 and 0 flags select the internal clock (master) or external clock (slave) operation. The SIO1HIZ flag selects whether the SO1/P0B2 pin is used as a serial data output pin. The SIO1MOD flag selects whether the SO1/SI1/P0B1 pin is used as a serial data input (SI1 pin) or serial data output (SO2) pin. Figure 15-2. Configuration of Serial I/O Clock Select Register Flag symbol Name b3 b2 b1 S I Serial I/O clock select register 0 0 O 1 C K 1 b0 S I O 1 C K 0 (BANK15) 1CH Address Read/ Write R/W Sets shift clock of serial interface 0 0 1 1 0 1 0 1 External clock 12.5 kHz 18.75 kHz 37.5 kHz Internal clock Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 0 0 Clock stop 150 PD17933, 17934 Figure 15-3. Configuration of Serial I/O Mode Select Register Flag symbol Name b3 b2 S I Serial I/O mode select register 0 O 1 M O D b1 S I O 1 H I Z b0 S I O 1 T S (BANK15) 1DH Address Read/ Write R/W Starts/stops serial communication 0 1 Stops (wait status) Starts Sets function of PDB2/SO1 pin 0 1 General-purpose input/output port Serial data output pin Selects function of P0B1/SI1/SO2 pin 0 1 As serial data input (SI1) pin As serial data output (SO2) pin Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 0 0 Clock stop 151 PD17933, 17934 Table 15-1. Set Status of Each Pin By Control Flags Control flags of serial interface Communication mode S I O 1 M O D Serial I/O select S I O 1 H I Z Serial S I interface O 1 pin setting C K 1 0 S I O 1 C K 0 0 Clock setting Pin name P 0 B B I O 2 I/O setting flag of each pin P 0 B B I O 1 P 0 B B I O 0 0 Set status of pin 3-wire serial I/O Note 1 External clock P0B0/SCK During wait: general-purpose input port Wait released: external clock input and 2-wire serial I/O Note 2 1 0 1 1 0 Internal clock (reception) 1 1 Output (transmission) 0 Generalpurpose I/O Serial output P0B2/SO1 0 1 0 1 0 1 1 0 1 P0B1/SI1/ SO2 0 Internal clock 0 1 General-purpose output port General-purpose input port During wait: waits for internal clock output Wait released: internal clock output During wait: general-purpose input port Wait released: serial input General-purpose output port During wait: waits for serial output Wait released: serial output General-purpose input port General-purpose output port During wait: waits for serial output Wait released: serial output 1 Notes 1. To set the 3-wire serial I/O mode, be sure to reset SIO1MOD to 0 and set SIO1HIZ to 1. 2. To use the 2-wire serial I/O mode, be sure to reset SIO1HIZ to 0. 152 PD17933, 17934 15.2.1 Setting 2-/3-wire mode The serial interface uses two pins in the two-wire mode: SCK/P0B0 and SO2/SI1/P0B1. The SCK/P0B0 pin is used as a shift clock input/output pin, and the SO2/SI1/P0B1 pin is used as a serial data input/output pin. The SO1/P0B2 pin is not used for the serial interface and is set in the general-purpose output port mode by the SIO1HIZ flag. In this way, the serial interface operates in the two-wire mode. In the three-wire mode, three pins, SCK/P0B0, SO1/P0B2, and SO2/SI1/P0B1 are used. The SCK/P0B0 is used as a shift clock input/output pin, the SO1/P0B2 pin is used as a serial data output pin, and the SO2/SI1/P0B1 pin is used as a serial data input pin. Unlike in the two-wire mode, the SO1/P0B2 pin is used as a serial data output pin according to the setting of the SIO1HIZ flag. The SO2/SI1/P0B1 pin is used as a serial data input pin according to the setting of the SIO1MOD flag. In this way, the serial interface operates in the three-wire mode. 15.2.2 Selecting data input/output using 2-wire serial interface In the two-wire mode, the SO2/SI1/P0B1 pin is used as an input/output pin for serial data. Whether the SO2/SI1/P0B1 pin is used as a serial data input pin (SI1 pin) or serial data output pin (SO2 pin) is specified by the SIO1MOD flag (refer to Figure 15-3 Configuration of Serial I/O Mode Select Register). 15.3 Clock Control Block The clock control block generates a clock when the internal clock is used (master operation), and controls clock output timing. The frequency fSC of the internal clock is set by the SIO1CK0 and SIO1CK1 flags of the serial I/O clock select register. Figure 15-2 shows the configuration and function of the serial I/O clock select register. For the clock generation timing, refer to 15.7 Operation of Serial Interface. 15.4 Clock Counter The clock counter counts the shift clock output or input from the shift clock pin (SCK/P0B0 pin). Because the clock counter directly reads the status of the clock pin, it cannot identify whether the clock is an internal clock or an external clock. The contents of the clock counter cannot be directly read by software. For the operation and timing chart of the clock counter, refer to 15.7 Operation of Serial Interface. 153 PD17933, 17934 15.5 Presettable Shift Register The presettable shift register is an 8-bit shift register that writes serial-out data and reads serial-in data. Writing/reading data to/from the presettable shift register is performed by PUT and GET instructions via data buffer. The presettable shift register outputs (transmits) the content of its most significant bit (MSB) from the serial data I/O pin in synchronization with the falling edge of the shift clock, and reads data to its least significant bit (LSB) in synchronization with the rising edge of the shift clock. Figure 15-4 shows the configuration and function of the presettable shift register. Figure 15-4. Configuration of Presettable Shift Register Data buffer DBF3 Don't care DBF2 Don't care DBF1 Transfer data GETNote 8 PUTNote Peripheral register Name Presettable shift register b7 M S B b6 b5 b4 b3 b2 b1 b0 Symbol Peripheral address L S SIO1SFR B DBF0 04H Valid data Setting of serial-out data and reading of serial-in data D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 Serial out Serial in Note If the PUT or GET instruction is executed during serial communication, the data may be lost. For details, refer to 15.8 Notes on Setting and Reading Data. 15.6 Wait Control Block The wait control block performs wait (pause) control of communication. By releasing the wait status by using the SIO1TS flag of the serial I/O mode select register, serial communication is started. After the wait status has been released, and communication has been started, the wait status is resumed if shift clock rises at clock counter "8". The communication status can be detected by the SIO1TS flag. That is, the communication status can be detected by detecting the status of the SIO1TS flag after setting "1" to the SIO1TS flag. If "0" is written to the SIO1TS flag while the wait status is released, the wait status is set. This is called a forced wait status. For the configuration and function of the serial I/O mode select register, refer to Figure 15-3. 154 PD17933, 17934 15.7 Serial Interface Operation The timing of each operation of the serial interface is described below. This timing is applicable to both 2-wire and 3-wire modes. 15.7.1 Timing chart Figure 15-5 shows a timing chart. Figure 15-5. Timing Chart of Serial Interface Shift clock Serial data La 1 D7 2 D6 3 D5 7 D1 8 D0 1 D7 Clock counter SIO1TS 0 1 2 3 6 7 8 0 <1> <2> <3> INT <4> <5> <6> Remark <1> Initial status (general-purpose input port) <2> Start condition satisfied by general-purpose I/O port <3> Wait released <4> Wait timing <5> General-purpose input port mode set <6> Stop condition satisfied by general-purpose I/O port 15.7.2 Operation of clock counter The initial value of the clock counter is "0". The value of the clock counter is incremented each time the falling edge of the clock pin has been detected. When the value of the clock counter reaches "8", it is reset to "0" at the next rising edge of the clock pin. After the clock counter has been reset to "0", the serial communication is placed in the wait status. The conditions under which the clock counter is reset are as follows: (1) (2) (3) (4) At power-ON reset When clock stop instruction is executed When "0" is written to SIO1TS flag If shift clock rises while wait status is released and present value of clock counter is "8" 155 PD17933, 17934 15.7.3 Wait operation and note When the wait status has been released, serial data is output at the next falling edge of the clock (transmission operation), and the wait released status continues until eight clocks are counted. After the eight clocks have been output, make the shift clock pin high and stop the operations of the clock counter and presettable shift register. Note that, if data is written to or read from the presettable shift register while the wait status is released and the shift clock pin is high, the correct data is not set. If data is written to the presettable shift register while the wait status is released and the shift clock pin is low, the content of the MSB of the data is output to the serial data output pin when the "PUT" instruction is executed. If the forced wait status is set while the wait status is released, the wait status is immediately set when "0" is written to the SIO1TS flag. 15.7.4 Interrupt request issuance timing An interrupt request is issued when eight clocks have been transmitted (received). 15.7.5 Shift clock generation timing (1) When wait status is released from initial status The "initial status" means the point at which the P0B0/SCK pin has been made high with the internal clock operation selected. During the wait status, a high level is output to the shift clock pin. The wait status can be released and a clock can be selected at the same time. 156 PD17933, 17934 Figure 15-6. Shift Clock Generation Timing of Serial Interface (1/4) Shift clock (37.5 kHz) 1:1 Wait status 1/fSC Initialization 13.33 s Wait released Shift clock (18.75 kHz) 1:1 Wait status 13.33 s Initialization Wait released 1/fSC Shift clock (12.5 kHz) 2:1 26.66 s Wait status 1/fSC Initialization Wait released (2) When wait operation is performed (a) When wait status is set at the 8th clock (normal operation) Figure 15-6. Shift Clock Generation Timing of Serial Interface (2/4) Shift clock Wait released status Contents of output latch Wait status 1/fSC Wait Wait released 157 PD17933, 17934 (b) When forced wait status is set during wait status Figure 15-6. Shift Clock Generation Timing of Serial Interface (3/4) Shift clock Contents of output latch Wait period Contents of output latch Wait period Forced wait by SIO1TS (c) When forced wait status is set while wait status is released Figure 15-6. Shift Clock Generation Timing of Serial Interface (4/4) Shift clock Wait released status Contents of output latch Wait status 1/fSC Forced wait by SIO1TS Wait released Shift clock Wait released status Contents of output latch Wait status 1/fSC Forced wait by SIO1TS Wait released (d) When wait status is released while wait status is released The clock output waveform does not change. Neither is the counter reset. However, do not change the clock frequency while the wait status is released. 158 PD17933, 17934 15.8 Notes on Setting and Reading Data Use the "PUT SIO1SFR, DBF" instruction to set data to the presettable shift register. Use the "GET DBF, SIO1SFR" instruction to read data. Set or read the data in the wait status. While the wait status is released, the data may not be correctly set or read depending on the status of the shift clock pin. The following table describes the points to be noted in setting and reading data. Table 15-2. Data Read and Write Operations of Presettable Shift Register and Notes Status on execution of PUT/GET Read (GET) Status of shift clock pin Normal read Operation of presettable shift register Wait status Write (PUT) * Floating with external clock * Value of output latch with internal clock. Normally, used with high level Normal write Content of MSB is output as data at falling edge of shift clock after wait status is released next (transmission operation). Clock Data MSB PUT SIO1SFR, DBF Low level Read (GET) High level Normal read Cannot be read normally. Contents of SIO1SFR are lost. Cannot be written normally. Contents of SIO1SFR are lost. Wait released Low level Wait release status Write (PUT) High level Normal write Content of MSB is output as data when PUT instruction is executed. Clock counter is not reset. Clock Data MSB PUT SIO1SFR, DBF 159 PD17933, 17934 15.9 Operation Mode and Operational Outline of Each Blocks Tables 15-3 and 15-4 outline the operations of the serial interface. Table 15-3. Operation in 3-wire Serial I/O Mode Operation mode Item Status of each pin SCK/P0B0 Slave operation (SIO1CK1 = SIO1CK0 = 0) During wait (SIO1TS = 0) * When P0BBIO0 = 0 General-purpose input port * When P0BBIO0 = 1 General-purpose output port SI1/SO2/P0B1 Wait released (SIO1TS = 1) * When P0BBIO0 = 0 External clock input port * When P0BBIO0 = 1 General-purpose output port Master operation (SIO1CK1 = SIO1CK0 = other than 0) During wait (SIO1TS = 0) * When P0BBIO0 = 0 General-purpose input port * When P0BBIO0 = 1 Waits for internal clock output SIO1MOD = 0 Wait released (SIO1TS = 1) * When P0BBIO0 = 0 General-purpose input port * When P0BBIO0 = 1 Internal clock output ----------------------------------------------------------------------------------------- * When P0BBIO1 = 0 General-purpose input port * When P0BBIO1 = 1 General-purpose output port SO1/P0B2 Waits for serial output Program counter Operation of presettable shift register Output * When P0BBIO1 = 0 Serial input * When P0BBIO1 = 1 General-purpose output port * When P0BBIO1 = 0 General-purpose input port * When P0BBIO1 = 1 General-purpose output port SIO1HIZ = 1 * When P0BBIO1 = 0 Serial input * When P0BBIO1 = 1 General-purpose output port ----------------------------------------------------------------------------------------- Serial output Waits for serial output Serial output Incremented at falling edge of SCK pin * When SIO1HIZ = 0 Not output * When SIO1HIZ = 1 Shifted from MSB and output from SO1 pin at falling edge of SCK pin Input * When SIO1MOD = 0 Shifted from LSB and status of SI1 pin is input at rising edge of SCK pin. If SI1 pin is set in output mode, however, contents of output latch are input. 160 PD17933, 17934 Table 15-4. Operation in Two-Wire Serial I/O Mode Operation mode Item Status of each pin SCK/P0B0 Slave operation (SIO1CK1 = SIO1CK0 = 0) During wait (SIO1TS = 0) * When P0BBIO0 = 0 General-purpose input port * When P0BBIO0 = 1 General-purpose output port Wait released (SIO1TS = 1) * When P0BBIO0 = 0 External clock input port * When P0BBIO0 = 1 General-purpose output port Master operation (SIO1CK1 = SIO1CK0 = other than 0) During wait (SIO1TS = 0) * When P0BBIO0 = 0 General-purpose input port * When P0BBIO0 = 1 Waits for internal clock output SIO1MOD = 0 Wait released (SIO1TS = 1) * When P0BBIO0 = 0 General-purpose input port * When P0BBIO0 = 1 Internal clock output SI1/SO2/P0B1 * When P0BBIO1 = 0 General-purpose input port * When P0BBIO1 = 1 General-purpose output port * When P0BBIO1 = 0 Serial input * When P0BBIO1 = 1 ----------------------------------------------------------------------------------------- * When P0BBIO1 = 0 General-purpose input port * When P0BBIO1 = 1 General-purpose output port SIO1MOD = 1 * When P0BBIO1 = 0 Serial input * When P0BBIO1 = 1 General-purpose output port General-purpose output port ----------------------------------------------------------------------------------------- Waits for serial output regardless of P0BBIO1 SO1/P0B2 * When P0BBIO2 = 0 General-purpose input port * When P0BBIO2 = 1 General-purpose output port Serial output regardless of P0BBIO1 Waits for serial output regardless of P0BBIO1 Serial output regardless of P0BBIO1 SIO1HIZ = 0 ----------------------------------------------------------------------------------------- * When P0BBIO2 = 0 Serial input * When P0BBIO2 = 1 General-purpose output port * When P0BBIO2 = 0 General-purpose input port * When P0BBIO2 = 1 General-purpose output port SIO1MOD = 1 * When P0BBIO2 = 0 Serial input * When P0BBIO2 = 1 General-purpose output port ----------------------------------------------------------------------------------------- Waits for serial output regardless of P0BBIO2 Program counter Operation of presettable shift register Input Output Serial output regardless of P0BBIO2 Waits for serial output regardless of P0BBIO2 Serial output regardless of P0BBIO2 Incremented at falling edge of SCK pin * When SIO1SEL = 1 Shifted from MSB and output from SO2 pin at falling edge of SCK pin * When SIO1SEL = 0 Shifted from LSB and status of SI1 pin is input at rising edge of SCK pin. If SI1 pin is set in output port mode, however, contents of output latch are input. 161 PD17933, 17934 15.10 Status on Reset 15.10.1 At reset by RESET pin P0B0/SCK, P0B1/SI1/SO2, and P0B2/SO1 pins are set in the general-purpose input port mode. The contents of the presettable shift register are undefined. 15.10.2 WDT&SP reset P0B0/SCK pin, P0B1/SI1/SO2, and P0B2/SO1 pins are set in the general-purpose input port. The previous contents of the presettable shift register are retained. 15.10.3 At clock stop All the pins hold the current status. The previous contents of the presettable shift register are retained. 15.10.4 In halt status All the pins hold the current status. The internal clock stops output in the status in which the HALT instruction is executed. When the external clock is used, the operation continued even if the HALT instruction is executed. 162 PD17933, 17934 16. PLL FREQUENCY SYNTHESIZER The PLL (Phase Locked Loop) frequency synthesizer is used to lock a frequency in the MF (Medium Frequency), HF (High Frequency), and VHF (Very High Frequency) to a constant frequency by means of phase difference comparison. 16.1 Outline of PLL Frequency Synthesizer Figure 16-1 outlines the PLL frequency synthesizer. A PLL frequency synthesizer can be configured by connecting an external lowpass filter (LPF) and voltage controlled oscillator (VCO). The PLL frequency synthesizer divides a signal input from the VCOH or VCOL pin by using a programmable divider and outputs a phase difference between this signal and a reference frequency from the EO0 and EO1 pins. Figure 16-1. Outline of PLL Frequency Synthesizer DBF VCOH VCOL PLLSCNF flag EO1 EO0 Note Input select block Programmable divider (PD) Phase comparator ( -DET) Charge pump Lowpass filter (LPF) 75 kHz Reference frequency generator Unlock FF Note Voltage controlled oscillator (VCO) PLLMD1 flag PLLMD0 flag PLLRFCK2 flag PLLRFCK1 flag PLLRFCK0 flag PLLUL flag Note External circuit PLLMD1 and PLLMD0 (bits 1 and 0 of PLL mode selection register: refer to Figure 16-3) selects a division mode of the PLL frequency synthesizer. 2. 3. 4. PLLSCNF (bit 3 of PLL mode selection register: refer to Figure 16-3) selects the least significant bit of the swallow counter. PLLRFCK2 through PLLRFCK0 (bits 3 through 0 of PLL reference frequency selection register: refer to Figure 16-6) selects a reference frequency fr of the PLL frequency synthesizer. PLLUL (bit 0 of PLL unlock FF register: refer to Figure 16-9) detects the PLL unlock FF status. Remarks 1. 163 PD17933, 17934 16.2 Input Selection Block and Programmable Divider 16.2.1 Configuration and function of input selection block and programmable divider Figure 16-2 shows the configuration of the input selection block and programmable divider. The input selection block selects an input pin and division mode of the PLL frequency synthesizer. The VCOH or VCOL pin can be selected as the input pin. The voltage on the selected pin is at the intermediate level (approx. 1/2 VDD). The pin not selected is internally pulled down. Because these pins are connected to an internal AC amplifier, cut the DC component of the input signal by connecting a capacitor in series to the pin. Direct division mode and pulse swallow mode can be selected as division modes. The programmable divider divides the frequency of the input signal according to the value set to the swallow counter and programmable counter. The pin and division mode to be used are selected by the PLL mode selection register. Figure 16-3 shows the configuration of the PLL mode selection register. The value of the programmable divider is set by using the PLL data register via data buffer. Figure 16-2. Configuration of Input Selection Block and Programmable Divider PLLMD1 flag PLLMD0 flag DBF 16 PLL data register 12 bits 4 bits 4 R F Note VCOH 2-modulus prescaler 1/32, 1/33 12 Swallow counter 5 bits Programmable counter 12 bits fN To -DET VCOL PLL disable signal Note PLLSCNF flag 164 PD17933, 17934 Figure 16-3. Configuration of PLL Mode Selection Register Name Flag symbol b3 b2 b1 b0 Address Read/Write PLL mode selection P L L S C N F 0 P L L P L L (BANK15) 10H R/W MM D 1 D 0 Selects division mode of PLL frequency synthesizer 0 0 1 1 0 1 0 1 Disables VCOL and VCOH pins Direct division (VCOL pin, MF mode) Pulse swallow (VCOH pin, VHF mode) Pulse swallow (VCOL pin, HF mode) Fixed to "0" Selects least significant bit of swallow counter 0 1 Clears least significant bit to 0 Sets least significant bit to 1 At reset Reset by RESET pin WDT&SP reset U U R 0 0 0 0 0 0 0 Clock stop U: Undefined R: Retained 16.2.2 Outline of each division mode (1) Direct division mode (MF) In this mode, the VCOL pin is used. The VCOH pin is pulled down. In this mode, only the programmable counter is used for frequency division. (2) Pulse swallow mode (HF) In this mode, the VCOL pin is used. The VCOH pin is pulled down. In this mode, the swallow counter and programmable counter are used for frequency division. 165 PD17933, 17934 (3) Pulse swallow mode (VHF) In this mode, the VCOH pin is used. The VCOL pin is pulled down. In this mode, the swallow counter and programmable counter are used for frequency division. (4) VCOL and VCOH pin disabled In this mode, only the VCOL and VCOH pins are internally pulled down, but the other blocks operate. 16.2.3 Programmable divider and PLL data register The programmable divider consists of a 5-bit swallow counter and a 12-bit programmable counter. Each counter is a 17-bit binary down counter. The programmable counter is allocated to the high-order 12 bits of the PLL data register, and the swallow counter is allocated to the low-order 4 bits. Data are set to these counters via data buffer. The least significant bit of the swallow counter sets data to the PLLSCNF flag of the control register. The value by which the input signal frequency is to be divided is called "N value". For how to set a division value (N value) in each division mode, refer to 16.6 Using PLL Frequency Synthesizer. (1) PLL data register and data buffer Figure 16-4 shows the relationships between the PLL data register and data buffer. In the direct division mode, the high-order 12 bits of the PLL data register are valid, and all 17 bits of the register are valid in the pulse swallow mode. In the direct division mode, all 12 bits are used as a programmable counter. In the pulse swallow mode, the high-order 12 bits are used as a programmable counter, and the low-order 5 bits are used as a swallow counter. (2) Relationship between division value N of programmable divider and divided output frequency The relationship between the value "N" set to the PLL data register and the signal frequency "fN" divided and output by the programmable divider is as shown below. For details, refer to 16.6 Using PLL Frequency Synthesizer. (a) Direct division mode (MF) fIN N fIN = N: 12 bits (b) Pulse swallow mode (HF, VHF) fIN N fIN = N: 17 bits 166 PD17933, 17934 Figure 16-4. Setting Division Value (N Value) of PLL Frequency Synthesizer Data buffer DBF3 DBF2 DBF1 DBF0 Transfer data GET PUT Peripheral register Name PLL data register b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 Symbol Peripheral address 42H PLLR Name PLL mode selection Register file b3 b2 b1 b0 address 16 Valid data P 0 P P (BANK15) LL L 10H LL L MM S DD C 10 N F Sets least significant bit of division value Note Sets high-order 16 bits of division value b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 b3 PLL N value data (17 bits) Sets division value (N value) of PLL frequency synthesizer Direct division mode 0 don't care Setting prohibited 15 (00FH) 16 (010H) don't care don't care b16 b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 x don't care Division value N: N = x 212-1 (FFFH) Pulse swallow mode 0 don't care Setting prohibited 1023 (3FFH) 1024 (400H) x Division value N: N = x 217-1 (1FFFFH) Note The value of PLLSCNF flag is transferred when a write (PUT) instruction is executed to the PLL data register (PLLR). Therefore, data must be set to the PLLSCNF flag before executing the write instruction to the PLL data register. 167 PD17933, 17934 16.3 Reference Frequency Generator Figure 16-5 shows the configuration of the reference frequency generator. The reference frequency generator generates the reference frequency "fr" of the PLL frequency synthesizer by dividing the 75 kHz output of a crystal oscillator. Six frequencies can be selected as reference frequency fr: 1, 3, 5, 6.25, 12.5, and 25 kHz. The reference frequency fr is selected by the PLL reference frequency selection register. Figure 16-6 shows the configuration and function of the PLL reference frequency selection registerion. Figure 16-5. Configuration of Reference Frequency Generator PLLRFCK2 flag PLLRFCK1 flag PLLRFCK0 flag MUX 1 kHz 3 kHz 5 kHz 75 kHz Divider 6.25 kHz 12.5 kHz 25 kHz To -DET OFF PLL disable signal 168 PD17933, 17934 Figure 16-6. Configuration of PLL Reference Frequency Selection Register Name Flag symbol b3 b2 b1 b0 Address Read/Write PLL reference frequency selection 0 P L L R F C K 2 P L L R F C K 1 P L L R F C K 0 (BANK15) 11H R/W Sets reference frequency fr of PLL frequency synthesizer 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 1 kHz 3 kHz 5 kHz 6.25 kHz 12.5 kHz 25 kHz PLL disable PLL disable Fixed to "0" At reset Reset by RESET Pin WDT&SP reset 0 0 0 1 1 1 1 1 1 1 1 1 Clock stop Remark When the PLL frequency synthesizer is disabled by the PLL reference frequency selection register, the VCOH and VCOL pins are internally pulled down. The EO1 and EO0 pins are floated. 169 PD17933, 17934 16.4 Phase Comparator (-DET), Charge Pump, and Unlock FF 16.4.1 Configuration of phase comparator, charge pump, and unlock FF Figure 16-7 shows the configuration of the phase comparator, charge pump, and unlock FF. The phase comparator compares the phase of the divided frequency "fN" output by the programmable divider with the phase of the reference frequency "fr" output by the reference frequency generator, and outputs an up (UP) or down (DW) request signal. The charge pump outputs the output of the phase comparator from an error out pin (EO1 and EO0 pins). The unlock FF detects the unlock status of the PLL frequency synthesizer. 16.4.2 through 16.4.4 describe the operations of the phase comparator, charge pump, and unlock FF. Figure 16-7. Configuration of Phase Comparator, Charge Pump, and Unlock FF PLLUL flag fr Reference frequency generator Phase comparator ( - DET) Programmable divider UP Unlock FF EO1 fN DW Charge pump EO0 PLL disable signal 170 PD17933, 17934 16.4.2 Function of phase comparator As shown in Figure 16-7, the phase comparator compares the phases of the divided frequency "fN" output by the programmable divider and the reference frequency "fr", and outputs an up or down request signal. If the divided frequency fN is lower than reference frequency fr, the up request signal is output. If fN is higher than fr, the down request signal is output. Figure 16-8 shows the relationship between reference frequency fr, divided frequency fN, up request signal, and down request signal. When the PLL frequency synthesizer is disabled, neither the up request nor the down request signal is output. The up and down request signals are input to the charge pump and unlock FF, respectively. Figure 16-8. Relationship between fr, fN, UP, and DW (a) If fN lags behind fr fr fN UP DW (b) If fN leads fr fr fN UP DW (c) If fN and fr are in phase fr fN UP DW (d) If fN is lower than fr fr fN UP DW 171 PD17933, 17934 16.4.3 Charge pump As shown in Figure 16-7, the charge pump outputs the up request and down request signals output by the phase comparator, from the error out pins (EO1 and EO0 pins). Therefore, the relationship between the output of the error out pins, divided frequency fN and reference frequency fr is as follows: Where reference frequency fr > divided frequency fN: Low-level output Where reference frequency fr < divided frequency fN: High-level output Where reference frequency fr = divided frequency fN: Floating 16.4.4 Unlock FF As shown in Figure 16-7, the unlock FF detects the unlock status of the PLL frequency synthesizer from the up request and down request signals of the phase comparator. Because either the up request or down request signal is low in the unlock status, the unlock status is detected by this low-level signal. In the unlock status, the unlock FF is set to 1. The unlock FF is set in the cycle of the reference frequency fr selected at that time. When the contents of the PLL unlock FF register are read (by the PEEK instruction), the unlock FF is reset (Read & Reset). Therefore, the unlock FF must be detected in a cycle longer than cycle 1/fr of the reference frequency fr. The status of the unlock FF is detected by the PLL unlock FF register. Figure 16-9 shows the configuration of the PLL unlock FF register. Because this register is a read-only register, its contents can be read to the window register by the "PEEK" instruction. Because the unlock FF is set in a cycle of the reference frequency fr, the contents of the PLL unlock FF register are read to the window register in a cycle longer than cycle 1/fr of the reference frequency. The delay time of the up and down request signals of the phase comparator are fixed to 0.8 to 1.0 s. 172 PD17933, 17934 Figure 16-9. Configuration of PLL Unlock FF Register Name Flag symbol b3 b2 b1 b0 Address Read/Write PLL unlock FF 0 0 0 P L L U L (BANK15) 12H R & Reset Detects status of unlock FF 0 1 Unlock FF = 0: PLL locked status Unlock FF = 1: PLL unlocked status Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 U U R Clock stop U: Undefined R: Retained 173 PD17933, 17934 16.5 PLL Disabled Status The PLL frequency synthesizer stops when PLL disabled status is selected by the PLL reference frequency register (RF address 11H). Table 16-1 shows the operation of each block in the PLL disabled status. When the VCOL and VCOH pins are disabled by the PLL mode selection register, only the VCOL and VCOH pins are internally pulled down, and the other blocks operate. At reset by RESET pin, the PLL frequency synthesizer is disabled. Table 16-1. Operation of Each Block under Each PLL Disable Condition Condition Each Block VCOL, VCOH pins Programmable divider Reference frequency generator Phase comparator Charge pump PLL reference frequency selection register = 1111B (PLL disabled) Internally pulled down Division stopped Output stopped Output stopped Error out pins are floated PLL mode selection register = 0000B (VCOH and VCOL disabled) Internally pulled down Operates Operates Operates Operates. However, usually outputs low level because no signal is input 174 PD17933, 17934 16.6 Using PLL Frequency Synthesizer To control the PLL frequency synthesizer, the following data is necessary. (1) Division mode (2) Pins used (4) Division value : Direct division (MF), pulse swallow (HF, VHF) : VCOL and VCOH pins :N (3) Reference frequency : fr 16.6.1 through 16.6.3 below describe how to set PLL data in each division mode (MF, HF, and VHF). 16.6.1 Direct division mode (MF) (1) Selecting division mode Select the direct division mode by using the PLL mode selection register. (2) Pins used The VCOL pin is enabled to operate when the direct division mode is selected. (3) Selecting reference frequency fr Select the reference frequency by using the PLL reference frequency selection register. (4) Calculation of division value N Calculate N as follows: fVCOL fr fVCOL : Input frequency of VCOL pin fr : Reference frequency N= (5) Example of setting PLL data How to set data to receive broadcasting in the following MW band is described below. Reception frequency Reference frequency : 1422 kHz (MW band) : 3 kHz Intermediate frequency : +450 kHz Division value N is calculated as follows: fVCOL fr 1422 + 450 3 N= = = 624 (decimal) = 270H (hexadecimal) Set data to the PLL data register, PLL mode selection register, and PLL reference frequency selection register as follows: 175 PD17933, 17934 PLL data register (PLLR) PLL mode PLL reference selection frequency Note 1 register selection register 0 don't care Note 2 0 0 MF 10 0 0 1 0 0 2 1 00 1 7 1 10 0 0 0 3 kHz Notes 1. PLLSCNF flag 2. don't care 176 PD17933, 17934 16.6.2 Pulse swallow mode (HF) (1) Selecting division mode Select the pulse swallow mode by using the PLL mode selection register. (2) Pins used The VCOL pin is enabled to operate when the pulse swallow mode is selected. (3) Selecting reference frequency fr Select the reference frequency by using the PLL reference frequency selection register. (4) Calculation of division value N Calculate N as follows: fVCOL fr fVCOL : Input frequency of VCOL pin fr : Reference frequency N= (5) Example of setting PLL data How to set data to receive broadcasting in the following SW band is described below. Reception frequency Reference frequency : 25.50 MHz (SW band) : 5 kHz Intermediate frequency : +450 kHz Division value N is calculated as follows: fVCOL fr 25500 + 450 5 N= = = 5190 (decimal) = 1446H (hexadecimal) Set data to the PLL data register, PLL mode selection register, and PLL reference frequency selection register as follows: Caution The division value N is 17 bits long when the pulse swallow mode is selected, and the least significant bit of the swallow counter is the bit 3 of the PLL mode selection register (PLLSCNF). To set "1446H" as the division value N, the value to be actually set to the PLL data register is "0A23H". PLL data register (PLLR) PLL mode PLL reference selection frequency Note register selection register 00 0 1 1 6 0 0 1 HF 10 0 1 0 0 0 0 1 01 0 1 4 00 0 1 4 5 kHz Note PLLSCNF flag 177 PD17933, 17934 16.6.3 Pulse swallow mode (VHF) (1) Selecting division mode Select the pulse swallow mode by using the PLL mode selection register. (2) Pins used The VCOH pin is enabled to operate when the pulse swallow mode is selected. (3) Selecting reference frequency fr Select the reference frequency by using the PLL reference frequency selection register. (4) Calculation of division value N Calculate N as follows: fVCOH fr fVCOH : Input frequency of VCOH pin fr : Reference frequency N= (5) Example of setting PLL data How to set data to receive broadcasting in the following FM band is described below. Reception frequency Reference frequency : 98.15 MHz (FM band) : 25 kHz Intermediate frequency : +10.7 MHz Division value N is calculated as follows: fVCOH fr 98.15 + 10.7 0.025 N= = = 4354 (decimal) = 1102H (hexadecimal) Set data to the PLL data register, PLL mode selection register, and PLL reference frequency selection register as follows: Caution The division value N is 17 bits long when the pulse swallow mode is selected, and the least significant bit of the swallow counter is the bit 3 of the PLL mode selection register (PLLSCNF). To set "1102H" as the division value N, the value to be actually set to the PLL data register is "0881H". PLL data register (PLLR) PLL mode PLL reference selection frequency Note register selection register 00 0 0 1 2 0 0 1 VHF 00 1 0 1 0 0 0 1 01 0 0 1 01 0 0 0 25 kHz Note PLLSCNF flag 178 PD17933, 17934 Note that data must be set to the PLLSCNF flag before a write (PUT) instruction is executed to the PLL data register (PLLR). Example SET1 MOV MOV MOV PUT PLLSCNF DBF0, #0 DBF1, #4 DBF2, #4 PLLR, DBF 16.7 Status at Reset 16.7.1 At reset by RESET pin The PLL frequency synthesizer is disabled because the PLL reference frequency selection register is initialized to 0111B. 16.7.2 At WDT&SP reset The PLL frequency synthesizer is disabled because the PLL reference frequency selection register is initialized to 0111B. 16.7.3 On execution of clock stop instruction The PLL frequency synthesizer is disabled because the PLL reference frequency selection register is initialized to 0111B. 16.7.4 In halt status The set status is retained. 179 PD17933, 17934 17. INTERMEDIATE FREQUENCY (IF) COUNTER 17.1 Outline of Frequency Counter Figure 17-1 outlines the frequency counter. The IF counter is mainly used to count the intermediate frequency (IF) output from a tuner for detecting broadcasting stations. The IF counter counts the frequency input to the P1C2/AMIFC or P1C3/FMIFC/AMIFC pin at fixed intervals (1 ms, 4 ms, 8 ms, or open) by using a 16-bit counter. Figure 17-1. Outline of IF Counter IFCCK1 flag IFCCK0 falg IFCSTRT flag DBF P1C2/AMIFC P1C3/FMIFC/AMIFC I/O selection block Gate time control block Start/stop control block IF counter (16 bits) IFCGOSTT flag IFCMD1 flag IFCMD0 flag IFCRES flag Remarks 1. 2. 3. 4. 5. IFCMD1 and IFCMD0 (bits 3 and 2 of IF counter mode selection register: refer to Figure 17-3) select the IF counter function. IFCCK1 and IFCCK0 (bits 1 and 0 of IF counter mode selection register: refer to Figure 17-3) select the gate time of the IF counter. IFCSTRT (bit 1 of IF counter control register: refer to Figure 17-5) control starting of the IF counter. IFCGOSTT (bit 0 of IF counter gate status detection register: refer to Figure 17-6) detects opening/ closing the gate of the IF counter function. IFCRES (bit 0 of IF counter control register: refer to Figure 17-5) reset the count value of the IF counter. 180 PD17933, 17934 17.2 IF Counter Input Selection Block and Gate Time Control Block Figure 17-2 shows the configuration of the IF counter input selection block and gate time control block. The IF counter selection block selects whether the P1C2/AMIFC or P1C3/FMIFC/AMIFC pin is used as an IF counter function or a general-purpose input port, by using the IF counter mode selection register. The gate time control block selects gate time by using the IF counter mode selection register when the frequency counter is used as the IF counter. Figure 17-3 shows the configuration of the IF counter mode selection register. Figure 17-2. Configuration of IF Counter Input Selection Block and Gate Time Control Block IFCMD1 flag IFCMD0 flag IFCCK1 flag IFCCK0 flag P1C3/FMIFC/AMIFC 1/2 Selector Gate signal generator Gate signal To start/stop control block P1C2/AMIFC Input port FMIFC AMIFC Frequency 181 PD17933, 17934 Figure 17-3. Configuration of IF Counter Mode Selection Register Name Flag symbol b3 b2 b1 b0 Address Read/Write IF counter mode selection I F C I F C I F C C K 1 I F C C K 0 (BANK15) 22H R/W MM D 1 D 0 Selects gate time of IF counter 0 0 1 1 0 1 0 1 1 ms 4 ms 8 ms Open Selects function of IF counter 0 0 1 1 0 1 0 1 IF counter OFF mode (general-purpose input port) AMIFC pin, AMIF count mode FMIFC pin, FMIF count mode, 1/2 division FMIFC pin, AMIF count mode At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 0 0 0 0 0 0 Clock stop 182 PD17933, 17934 17.3 Start/Stop Control Block and IF Counter 17.3.1 Configuration of start/stop control block and IF counter Figure 17-4 shows the configuration of the start/stop control block and IF counter. The start/stop control block starts the frequency counter or detects the end of counting. The counter is started by the IF counter control register. The end of counting is detected by the IF counter gate status detection register. Figure 17-6 shows the configuration of the IF counter control register. Figure 17-7 shows the configuration of the IF counter gate status detection register. 17.3.2 describes the gate operation when the IF counter function is selected. The IF counter is a 16-bit binary counter that counts up the input frequency when the IF counter function is selected. When the IF counter function is selected, the frequency input to a selected pin is counted while the gate is opened by an internal gate signal. The frequency count is counted without alteration in the AMIF count mode. In the FMIF counter mode, however, the frequency input to the pin is halved and counted. When the IF counter counts up to FFFFH, it remains at FFFFH until reset. The count value is read by the IF counter data register (IFC) via data buffer. The count value is reset by the IF counter control register. Figure 17-7 shows the configuration of the IF counter data register. Figure 17-4. Configuration of Start/Stop Control Block and IF Counter DBF 16 IFCSTRT flag IF counter data register (IFC) IFCGOSTT flag IFCRES flag 16 Gate signal From gate time selection block Frequency Start/Stop control RES IF counter (16 bits) 183 PD17933, 17934 Figure 17-5. Configuration of IF Counter Control Register Name Flag symbol b3 b2 b1 b0 Address Read/Write IF counter control 0 0 I F C S T R T I F C R E S (BANK15) 23H W Resets data of IF counter 0 1 Nothing is affected Resets counter Start IF counter 0 1 Nothing is affected Resets counter Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 0 0 Clock stop 184 PD17933, 17934 Figure 17-6. Configuration of IF Counter Gate Status Detection Register Name Flag symbol b3 b2 b1 b0 Address Read/Write IF counter gate status detection 0 0 0 I F C G O S T T (BANK15) 21H R Detects opening/closing of gate of IF counter 0 1 Close Open Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 Clock stop Caution Do not read the contents of the IF counter data register (IFC) to the data buffer while the IFCGOSTT flag is set to 1. 185 PD17933, 17934 17.3.2 Operation of gate when IF counter function is selected (1) When gate time of 1, 4, or 8 ms is selected The gate is opened for 1, 4, or 8 ms from the rising of the internal 1-kHz signal after the IFCSTRT flag has been set to 1, as illustrated below. While this gate is open, the frequency input from a selected pin is counted by a 16-bit counter. When the gate is closed, the IFCGOSTT flag is cleared to 0. The IFCGOSTT flag is automatically set to 1 when the IFCSTRT flag is set. Internal 1 kHz 1 ms Gate time 4 ms 8 ms H L OPEN CLOSE Count period (IFCGOSTT flag = 1) Gate is actually opened at this point IFCSTRT flag is set IFCGOSTT flag is set at this point End of counting IFGOSTT flag is cleared (2) When gate is open If opening of the gate is selected by the IFCCK1 and IFCCK0 flags, the gate is opened as soon as its opening has been selected, as illustrated below. If the counter is started by using the IFCSTRT flag while the gate is open, the gate is closed after undefined time. To open the gate, therefore, do not set the IFCSTRT flag to 1. However, the counter can be reset by the IFCRES flag. H Internal 1 kHz L OPEN Gate CLOSE Count period Gate is closed after undefined time if IFCSTRT flag is set during this period Sets IFCCK1 = IFCCK0 = 1 Gate is actually opened at this point. If gate is opened while IFCGOSTT flag is 1, it is closed after undefined time The gate is opened or closed in the following two ways when opening the gate is selected as the gate time. 186 PD17933, 17934 (a) Resetting the gate to other than open by using IFCCK1 and IFCCK0 flags Gate OPEN CLOSE Count period IFCCK1 = IFCCK0 = 1 Resetting the gate to other than open by IFCCK1 and IFCCK0 flags (b) Unselect pin used by using IFCMD1 and IFCMD0 flags In this way, the gate remains open, and counting is stopped by disabling input from the pin. OPEN CLOSE Gate Count period Sets IFCCK1 = IFCCK0 = 1 Sets IFCMD1 = IFCMD0 = 0 (general-purpose input port) FMIFC and AMIFC pins are unselected and count signal cannot be input 17.3.3 Function and operation of 16-bit counter The 16-bit counter counts up the frequency input within selected gate time. The 16-bit counter can be reset by writing "1" to the IFCRES flag of the IF counter control register. Once the 16-bit counter has counted up to FFFFH, it remains at FFFFH until it is reset. The IF counter counts the frequency input to the P1C2/AMIFC or P1C3/FMIFC/AMIFC pin while the gate is open. Note, however, in the FMIF count mode input to the P1C3/FMIFC/AMIFC is divided by two and counted. The relationship between count value "x (decimal)" and input frequencies (fFMIFC and fAMIFC) is shown below. * FMIFC fFMIFC = * AMIFC fAMIFC = x tGATE (kHz) tGATE: gate time (1 ms, 4 ms, 8 ms) x tGATE x 2 (kHz) tGATE: gate time (1 ms, 4 ms, 8 ms) The value of the IF counter data register is read via data buffer. Figure 17-7 shows the configuration and function of the IF counter data register. 187 PD17933, 17934 Figure 17-7. Configuration of IF Counter Data Register Data buffer DBF3 DBF2 DBF1 DBF0 Transfer data GET can be executed 16 PUT changes nothing Peripheral register Name IF counter data register Valid data b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 Symbol Peripheral address IFC 43H Count value of IF counter 0 * FMIF count mode of FMIFC pin Counts rising edge of signal input to P1C3/FMIFC/AMIFC pin via 1/2 divider * AMIF count mode of AMIFC pin x Counts rising edge of signal input to P1C2/AMIFC pin * AMIF count mode of FMIFC pin Counts rising edge of signal input to 2 -1 (FFFFH) 16 P1C3/FMIFC/AMIMC pin Once the IF counter data register has counted up to FFFFH, it remains at FFFFH until the counter is reset. 188 PD17933, 17934 17.4 Using IF Counter The following sections 17.4.1 through 17.4.3 describe how to use the hardware of the IF counter, a program example, and count error. 17.4.1 Using hardware of IF counter Figure 17-8 shows the block diagram when the P1C2/AMIFC and P1C3/FMIFC/AMIFC pins. As shown in the figure, the IF counter uses an input pin with an AC amplifier, the DC component of the input signal must be cut with a capacitor. When the P1C2/AMIFC or P1C3/FMIFC/AMIFC pin is selected for the IF counter function, switch SW turns ON, and the voltage level on each pin reaches about 1/2VDD. If the voltage has not risen to a sufficient intermediate level at this time, the IF counter does not operate normally because the AC amplifier is not in the normal operating range. Therefore, make sure that a sufficient wait time elapses after each pin has been specified to be used for the IF counter until counting is started. Figure 17-8. IF Count Function Block Diagram of Each Pin R SW C External frequecny FMIFC AMIFC To internal counter 189 PD17933, 17934 17.4.2 Program example of IF counter A program example of the IF counter is shown below. As shown in this example, make sure that a wait time elapses after an instruction that selects the P1C2/AMIFC or P1C3/FMIFC/AMIFC pin for the IF counter function has been executed until counting is started. This is because, as described in 17.4.1, the internal AC amplifier does not operate normally immediately after a pin has been selected for the IF counter. Example To count the frequency input to the P1C3/FMIFC pin (FMIF count mode) (gate time: 8 ms) INITFLG IFCMD1, NOT IFCMD0, IFCCK1, NOT IFCCK0 ; Selects FMIFC pin (FMIF count mode), and sets gate time to 8 ms Wait SET1 SET1 LOOP: SKT1 BR IFCG0STT READ ; Detects opening or closing of gate ; Branches to READ: if gate is closed IFCRES IFCSTRT ; Internal AC amplifier stabilization time ; Resets counter ; Starts counting Processing A BR READ: GET 17.4.3 Error of IF counter The errors of the IF counter include a gate time error and a count error. The following paragraphs (1) and (2) describe each of these errors. (1) Gate time error The gate time of the IF counter is created by dividing the 75-kHz clock. Therefore, if the system clock is shifted from 75 kHz by "+x" ppm, the gate time is shifted by "-x" ppm. (2) Count error The IF counter counts frequency by the rising edge of the input signal. If a high level is input to the pin when the gate is open, therefore, one excess pulse is counted. If the gate is closed, however, a count error due to the status of the pin does not occur. Therefore, the count error is "+1, -0". DBF, IFC ; Reads value of IF counter data register to data buffer LOOP ; Do not read data of IF counter with this processing A 190 PD17933, 17934 17.5 Status at Reset 17.5.1 At reset by RESET pin The P1C2/AMIFC and P1C3/FMIFC/AMIFC pins are set in the general-purpose input port mode. 17.5.2 At WDT&SP reset The P1C2/AMIFC and P1C3/FMIFC/AMIFC pins are set in the general-purpose input port mode. 17.5.3 On execution of clock stop instruction The P1C2/AMIFC and P1C3/FMIFC/AMIFC pins are set in the general-purpose input port mode. 17.5.4 In halt status The P1C2/AMIFC and P1C3/FMIFC/AMIFC pins retain the status immediately before the halt mode is set. 191 PD17933, 17934 18. BEEP 18.1 Outlines of BEEP Figure 18-1 outlines BEEP. BEEP outputs a clock of 1.5 kHz or 3 kHz from the BEEP pin. The output select block selects, by using the BEEP0SEL flag, whether the P0B3/BEEP pin is used as a generalpurpose I/O port pin or BEEP output pin. The BEEP0CK0 and BEEP0CK1 flags of the BEEP clock select register are used to select whether the output frequency of the P0B3/BEEP pin is 1.5 kHz or 3 kHz, or the output level of the BEEP pin. The clock generation block generates the 1.5-kHz or 3-kHz clock to be output to the P0B3/BEEP pin. Figure 18-2 shows the configuration and function of the BEEP clock select register. Figure 18-1. Outline of BEEP BEEP0CK0 flag BEEP0CK1 flag BEEP0SEL flag Output select P0B3/BEEP block 1.5 kHz Clock generation block 3 kHz 192 PD17933, 17934 Figure 18-2. Configuration and Function of BEEP Clock Select Register Flag symbol Name b3 b2 B BEEP clock select register 0 E E P 0 S E L b1 B E E P 0 C K 1 b0 B E E P 0 C K 0 (BANK15) 14H Address Read/ Write R/W Setting of BEEP pin (when BEEP0SEL=1) 0 0 1 1 0 1 0 1 Outputs low level Outputs high level Outputs 1.5 kHz clock Outputs 3 kHz clock Selecting general-purpose I/O port and BEEP 0 1 Uses P0B3/BEEP pin as general-purpose I/O port Uses P0B3/BEEP pin as BEEP Fixed to 0 At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 0 0 0 0 0 0 Clock stop 193 PD17933, 17934 18.2 Output Wave Form of BEEP (1) Output wave of f = 1.5 kHz and f = 3 kHz BEEP (f = 1.5 kHz) 333.3 s 333.3 s BEEP (f = 3 kHz) 133.3 s 200 s Example Program to output 3-kHz clock from P0B3/BEEP pin BANK1 MOV 14H, #0011B ; Same as MOV BANK, #0001B ; Writes 0011B to data memory address 14H ; Outputs 3 kHz from BEEP pin (2) Maximum time until clock is output from P0B3/BEEP pin after instruction execution BEEP (f = 1.5 kHz) 325.8 s Instruction execution BEEP (f = 3 kHz) 325.8 s Instruction execution (3) Minimum time until clock is output from P0B3/BEEP pin after instruction execution BEEP (f = 1.5 kHz) 133.3 s Instruction execution BEEP (f = 3 kHz) 133.3 s Instruction execution 194 PD17933, 17934 18.3 Status at Reset 18.3.1 At reset by RESET pin The P0B3/BEEP pin is set in the general-purpose input port mode. 18.3.2 WDT&SP reset P0B3/BEEP pin is set in the general-purpose input port mode. 18.3.3 On execution of clock stop instruction The P0B3/BEEP pin is set in the general-purpose input/output port mode. 18.3.4 In halt status The P0B3/BEEP output pin retains the previous status. 195 PD17933, 17934 19. LCD CONTROLLER/DRIVER The LCD (Liquid Crystal Display) controller/driver can display an LCD of up to 60 dots by a combination of command signal and segment signal outputs. 19.1 Outline of LCD Controller/Driver Figure 19-1 outlines the LCD controller/driver. The LCD controller/driver can be used to display up to 60 dots by using a combination of common signal output pins (COM0 through COM3) and segment signal output pins (LCD0 through LCD19). The drive mode is 1/4 duty, 1/2 bias, the frame frequency is 62.5 Hz, and drive voltage is VLCD. Among the segment signal output pins, LCD17 through LCD19 can be used as a general-purpose input port. For details of the general-purpose input port, refer to 11.3 GENERAL-PURPOSE INPUT PORT (P0D, P1C, P2A). Figure 19-1. Outline of LCD Controller/Driver LCD0 pin Segment signal output timing control block LCD segment register (data memory space) ... P2A0/LCD17 pin P2A1/LCD18 pin P2A2/LCD19 pin Segment signal/ general input port select block ... LCD19SEL-LCD17SEL COM0 pin LCDEN flag COM3 pin Common signal output timing control block Basic clock for timing control ... REGLCD0 pin REGLCD1 pin REGLCD2 pin CAP LCD0 pin CAP LCD1 pin CAPLCD2 pin CAPLCD3 pin LCD drive voltage generation block Remarks 1. LCDEN (bit 0 of LCD driver display start register: refer to Figure 19-8) turns ON/OFF all LCD display. 2. LCD19SEL-LCD17SEL (bits 2-0 of LCD port select register: refer to Figure 19-6) 196 ... PD17933, 17934 19.2 LCD Drive Voltage Generation Block The LCD drive voltage generation block generates a voltage to drive the LCD. The PD17934 supplies the LCD drive voltage from an external doubler circuit. To configure a doubler circuit, connect a capacitor to the CAPLCD0, CAPLCD1, CAPLCD2, CAPLCD3, REGLCD0, REGLCD1, and REGLCD2 pins. Figure 19-2 shows an example of configuration of the doubler circuit. To use a voltage of 3.0 V (TYP.), connect as shown in Figure 19-2. To operate the doubler circuit, the LCDEN flag of the LCD display start register must be set to "1". Unless this flag is set to "1", the LCD drive voltage generation block does not operate. For the LCDEN flag, refer to 19.5 Common Signal Output and Segment Signal Output Timing Control Blocks. Figure 19-2. Configuration of Doubler Circuit VLCD1 C5 REGLCD2 CAPLCD3 C2 CAPLCD2 C4 REGLCD1 REGLCD0 C3 CAPLCD1 CAPLCD0 VLCD0 C1 C1 to C5 = 0.33 F Remark ( ): pin number Note that, because of the configuration of the doubler circuit, the values of the LCD drive voltages (VLCD1 and VLCD0) differ if the values of C1, C2, C3, C4, and C5 are changed. 197 PD17933, 17934 19.3 LCD Segment Register The LCD segment register sets dot data to turn on or turn off dots on the LCD. Figure 19-3 shows the location in the data memory and configuration of the LCD segment register. Because the LCD segment register is located in data memory, it can be controlled by all the data memory manipulation instructions. One nibble of the LCD segment register can set display data of 4 dots (data to turn dots on or off). If the LCD segment register is set to "1" at this time, the LCD display dot is on; the dot goes off if the register is set to "0". Figure 19-4 shows the relation between the LCD segment register and LCD display dot. Figure 19-3. Location on Data Memory and Configuration of LCD Segment Register Column address 0 0 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 A B C D E F DBF BANK0 B BANK14 Data memory C D E F 0 1 2 3 4 5 6 7 Row address LCD segment register System register LCD segment register (BANK 14) Address 5CH 5DH 5EH 5FH 60H 61H 62H 63H 64H 65H 66H 67H 68H 69H 6AH 6BH 6CH 6DH 6EH 6FH Symbol LCDD19 LCDD18 LCDD17 LCDD16 LCDD15 LCDD14 LCDD13 LCDD12 LCDD11 LCDD10 LCDD9 LCDD8 LCDD7 LCDD6 LCDD5 LCDD4 LCDD3 LCDD2 LCDD1 LCDD0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W LCDD19 b3 b2 b1 b0 R/W 198 Figure 19-4. Relation between LCD Segment Register and LCD Display Dot LCD segment register Address Symbol Bit 5CH LCDD19 5DH LCDD18 5EH LCDD17 5FH LCDD16 60H LCDD15 61H LCDD14 62H LCDD13 6EH LCDD1 6FH LCDD0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 B C D A B C D E F G H A B C D E F G H A B C D E F G H A B C D E F G H Display dot A COM3 pin A A E A E A E A E COM2 pin B B F B F B F B F COM1 pin C C G C G C G C G COM0 pin D D H D H D H D H LCD19/P2A2 pin LCD18/P2A1 pin LCD17/P2A0 pin LCD16 pin LCD15 pin LCD14 pin LCD13 pin LCD1 pin LCD0 pin PD17933, 17934 199 PD17933, 17934 19.4 Segment Signal/General-Purpose Input Port Select Block Figure 19-5 shows the configuration of the segment signal/general-purpose input port select block. This block specifies, by using the LCD19SEL through LCD17SEL flags of the LCD port select register, whether each pin is used as a segment signal output pin or a general-purpose input port pin. When each flag is "1", the corresponding pin is used as a segment signal output pin; when it is "0", the pin is used as a general-purpose input port pin. Figure 19-6 shows the configuration of the LCD port select register. Figure 19-5. Configuration of Segment Signal/General-Purpose Port Select Block LCD19SEL flag Note 1 LCD19/P2A2 0 Segment signal Segment signal/key source signal from output timing control block From bit 2 of P2A Note Port data input LCD17/P2A0 Note The LCD19/P2A2 pin corresponds to the LCD19SEL flag and bit 2 of P2A, the LCD18/P2A1 pin, to the LCD18SEL flag and bit 1 of P2A, and the LCD17/P2A0 pin, to the LCD17SEL flag and bit 0 of P2A, respectively. 200 PD17933, 17934 Figure 19-6. Configuration of LCD Port Select Register Flag symbol Name b3 b2 L C D 1 9 S E L b1 L C D 1 8 S E L b0 L C D 1 7 S E L Address Read/ Write LCD port select register 0 69H R/W Selects LCD segment signal output pin or general-purpose input port pin 0 1 Uses LCD17/P2A0 pin as general-purpose input port pin. Uses LCD17/P2A0 pin as LCD segment pin. Selects LCD segment signal output pin or general-purpose input port pin 0 1 Uses LCD18/P2A1 pin as general-purpose input port pin. Uses LCD18/P2A1 pin as LCD segment pin. Selects LCD segment signal output pin or general-purpose input port pin 0 1 Uses LCD19/P2A2 pin as general-purpose input port pin. Uses LCD19/P2A2 pin as LCD segment pin. Fixed to "0". At reset Reset by RESET pin WDT & SP reset 0 0 0 R 0 0 R 0 0 R Clock stop R: Retained 201 PD17933, 17934 19.5 Common Signal Output and Segment Signal Output Timing Control Blocks Figure 19-7 shows the common signal output and segment signal output timing control blocks. The common signal output timing control block controls the common signal output timing of the COM0 through COM3 pins. The segment signal output timing control block controls the segment signal output timing of the LCD0 through LCD19 pins. The common and segment signals are output when the LCDEN flag of the LCD driver display start register is set to "1". When this flag is reset to "0", all the LCD display dots can be extinguished (refer to Figure 19-8). When LCD display is not carried out, the COM0 through COM3 and LCD0 through LCD19 pins output low level. Figure 19-7. Configuration of Common Signal Output and Segment Signal Output Timing Control Blocks b0 LCD0 Segment signal | LCD19 Segment signal output timing control block b1 b2 LCDD19 b3 LCDD0 | Basic clock for timing control LCDEN flag COM0 Common signal | COM3 Common signal output timing control block 202 PD17933, 17934 Figure 19-8. Configuration of LCD Driver Display Start Register Flag symbol Name b3 L C D D B C K Note Read/ Address b0 L C (BANK15) 40H R/W Write b2 b1 LCD driver display start register 0 0 D E N Sets ON/OFF of all LCD displays 0 1 Display OFF (all segment and common output pins output low level) Display ON Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 0 0 0 0 0 0 0 0 Clock stop Remark R: Retained Note Bit 3 of the LCD display start register is a test mode area. Therefore, do not write "1" to this bit. 19.6 Common Signal and Segment Signal Output Waves Figure 19-9 shows an example of the common signal and segment signal output waves. The PD17934 outputs a signal with a frame frequency of 62.5 Hz using a 1/4 duty, 1/2 bias (voltage average method) drive mode. As the common signals, the COM0 through COM3 pins output three levels of voltages (GND, VLCD0, and VLCD1) each having a phase difference of 1/8 from the others. In other words, voltages of 1/2VDD are output with the VLCD0 as the reference. This display method is called the 1/2 bias drive method. As the segment signals, the segment signal output pins output voltages of two levels (GND and VLCD1) having a phase corresponding to each display dot. Because one segment pin can turn on or off four display dots (A, B, C, and D) as shown in Figure 19-9, sixteen phases can be output by combining lighting and extinguishing of each dot. Each display dot turnd on when the potential difference between a common signal and a segment signal is VLCD1. In other words, the duty factor at which each display dot turns on is 1/4. This display method is called the 1/4 duty display method, and the frame frequency is 62.5 Hz. 203 PD17933, 17934 Figure 19-9. Common Signal and Segment Signal Output Waveforms COM0 pin A COM1 pin B COM2 pin C COM3 pin D Each segment signal output pin (LCDn pin) Common signal 1 frame (16 ms) 4 ms VLCD1 COM0 pin VLCD0 GND VLCD1 COM1 pin VLCD0 GND VLCD1 COM2 pin VLCD0 GND VLCD1 COM3 pin VLCD0 GND Segment signal (example) A, B, C, D = extinguishes VLCD1 LCDn pin GND A, B, C, D = lights VLCD1 LCDn pin GND A, B, C = lights, D = extinguishes VLCD1 LCDn pin GND 204 PD17933, 17934 19.7 Using LCD Controller/Driver Figure 19-10 shows an example of wiring of an LCD panel using the pins LCD0 through LCD14. An example of a program that lights the 7 segments connected to LCD0 and LCD1 pins shown in Figure 19-10 is given below. Example PMN0 CH LCDDATA: DW DW DW DW DW DW DW DW DW DW MOV MOV MOV MOV LD LD LD LD ADD ADDC ADDC ADDC ST ST ST ST MOVT BANK1 ST ST SET1 SET1 LCDD0, DBF0 LCDD1, DBF1 CH LCDEN ; LCD ON 0000000000000000B 0000000000000110B 0000000010110101B 0000000010100111B 0000000001100110B 0000000011100011B 0000000011110011B 0000000010000110B 0000000011110111B 0000000011100111B MEM FLG 0.01H LCDD0.3 ; Preset number storage area ; Defines symbol with high-order 1 bit of LCD0 register for `CH' display ; LCD segment table data ; BLANK ;1 ;2 ;3 ;4 ;5 ;6 ;7 ;8 ;9 AR0, #.DL.LCDDATA SHR 12 AND 0FH AR1, #.DL.LCDDATA SHR 8 AND 0FH AR2, #.DL.LCDDATA SHR 4 AND 0FH AR3, #.DL.LCDDATA DBF0, AR0 DBF1, AR1 DBF2, AR2 DBF3, AR3 DBF0, PMN0 DBF1, #0 DBF2, #0 DBF3, #0 AR0, DBF0 AR1, DBF1 AR2, DBF2 AR3, DBF3 DBF, @AR ; Table reference instruction AND 0FH 205 206 FM MW SW LW COM3 COM1 COM2 COM0 Figure 19-10. Example of Wiring of LCD Panel (When LCD0-LCD14 Pins Are Used) A B C D 1a 1 f 1g 1 e 1d 1 c 2 e 1 b 2 f 2a 2 b 2g 2 c 2d 3 e 3 f 3a 3 b 3g 3 c 3d 4 e 4 f 4a 4 b 4g 4 c 4d E F G AM PM MHz kHz 5 e 5 f 5a 5 b 5g 5 c 5d CH Common COM3 LCD14 Correspondence of Segment and Common Pins, and LCD Panel Display (When LCD0-LCD14 Pins Are Used) Segment Pin L C D 14 L C D 13 L C D 12 L C D 11 L C D 10 L C D 9 L C D 8 L C D 7 L C D 6 L C D 5 L C D 4 L C D 3 L C D 2 L C D 1 L C D 0 LCD13 LCD12 LCD11 LCD10 LCD9 LCD8 LCD7 LCD6 LCD5 LCD4 LCD3 LCD2 LCD1 LCD0 FM B 1a 2a 3a C 4a D E AM 5a CH ** COM2 MW A 1f 1b 2f 2b 3f 3b 4f 4b F PM 5f 5b PD17933, 17934 COM1 SW 1g 1c 2g 2c 3g 3c 4g 4c G MHz 5g 5c COM0 LW 1e 1d 2e 2d 3e 3d 4e 4d kHz 5e 5d PD17933, 17934 19.8 Status at Reset 19.8.1 At reset by RESET pin The LCD0 through LCD16 pins output a low level. The LCD17/P2A0 through LCD19/P2A2 pins are set in the general purpose input port. The COM0 through COM3 pins also output a low level. Therefore, the LCD display is OFF. The contents of the LCD segment register are undefined. 19.8.2 WDT&SP reset The LCD0 through LCD16 pins output a low level. The LCD17/P2A0 through LCD19/P2A2 pins are set in the general-purpose input port. The COM0 through COM3 pins output a low level. Therefore, the LCD display is OFF. The contents of the LCD segment register are undefined. 19.8.3 On execution of clock stop instruction The LCD0 through LCD16 pins output a low level. The LCD17/P2A0 through LCD19/P2A2 pins are set in the general purpose input port. The COM0 through COM3 pins also output a low level. Therefore, the LCD display is OFF. The LCD segment register retains the previous contents. 19.8.4 In halt status The LCD0 through LCD19 pins output segment signals. The COM0 through COM3 pins output common signals. The LCD segment register retains the previous contents. 207 PD17933, 17934 20. STANDBY The standby function is used to reduce the current consumption of the device while the device is backed up. 20.1 Outline of Standby Function Figure 20-1 outlines the standby block. The standby function reduces the current consumption of the device by partly or totally stopping the device operation. The following two types of standby functions are available for selection as the application requires. * Halt function * Clock stop function The halt function reduces the current consumption of the device by stopping the CPU operation by using a dedicated instruction "HALT h". The clock stop function reduces the current consumption of the device by stopping the oscillation of the oscillation circuit by using a dedicated instruction "STOP s". Figure 20-1. Outline of Standby Block CPU Interrupt control block Halt control circuit HALT h Program counter BTM0CY Instruction decoder P0D3/AD2 P0D2/AD1 P0D1/AD0 P0D0 Input latch ALU Clock stop control circuit STOP s System register Oscillation circuit XOUT Control register XIN 208 PD17933, 17934 20.2 Halt Function 20.2.1 Outline of halt function The halt function stops the operating clock of the CPU by executing the "HALT h" instruction. When this instruction is executed, the program is stopped until the halt status is later released. Therefore, the current consumption of the device in the halt status is reduced by the operating current of the CPU. The halt status is released by using basic timer 0 carry FF, interrupt, or port input (P0D). The release condition is specified by operand "h" of the "HALT h" instruction. 20.2.2 Halt status In the halt status, all the operations of the CPU are stopped. In other words, execution of the program is stopped at the "HALT h" instruction. However, the peripheral hardware units continue the operation specified before execution of the "HALT h" instruction. For the operation of each peripheral hardware unit, refer to 20.4 Device Operation in Halt and Clock Stop Status. 20.2.3 Halt release condition Figure 20-2 shows the halt release condition. The halt release condition is specified by 4-bit data specified by operand "h" of the "HALT h" instruction. The halt status is released when the condition specified by "1" in operand "h". When the halt status is released, program execution is started from the instruction after the "HALT h" instruction. If the halt status is released by an interrupt, the operation to be performed after the halt status has been released differs depending on whether the interrupts are enabled (EI status) or disabled (DI status) when an interrupt source (IRQxxx = 1) is issued with the interrupt (IPxxx = 1) enabled. If two or more releasing conditions are specified, the halt status is released when one of the specified condition is satisfied. If 0000B is set as halt release condition "h", no releasing condition is set. If the device is reset at this time, the halt status is released. Figure 20-2. Halt Release Condition HALT h (4 bits) Operand b3 b2 b1 b0 Sets halt status releasing condition Released when high level is input to port 0D Released when basic timer 0 carry FF is set to 1 Undefined (Fix this bit to "0".) Released when interrupt is accepted 0 1 Not released even if condition is satisfied Released if condition is satisfied 209 PD17933, 17934 20.2.4 Releasing halt by input port (P0D) The halt releasing condition using an input port is specified by the "HALT 0001B" instruction. When the halt releasing condition using an input port is specified, the halt status is released if a high level is input to one of the P0D0 through P0D3 pins. The P0D0 through P0D3 pins are multiplexed with the A/D converter input pins AD0 through AD2 (except P0D0) and the halt status is not released when these pins are used as A/D converter input pins. An example is given below. * To use as key matrix The P0D0 through P0D3 pins are general-purpose input port pins which can be set in the input or output mode in 1-bit units and can be connected to an internal pull-down resistor. If connection of the internal pull-down resistor is specified by software, an external resistor can be eliminated as shown in this example (the internalpull down resistor is connected at reset by the RESET pin.) P0D3/AD2 Latch P0DPLD3 flag P0D2/AD1 P0D1/AD0 Switch A P0D0 General-purpose output port The "HALT 0001B" instruction is executed after the general-purpose output ports for key source signal are made high. Note that if an alternate switch is used as shown by switch A in the above figure, the halt status is released immediately because a high level is input to the P0D0 pin while switch A is closed. 210 PD17933, 17934 20.2.5 Releasing halt status by basic timer 0 carry FF Releasing the halt status by using the basic timer 0 carry FF is specified by the "HALT 0010B" instruction. When releasing the halt status by the basic timer 0 carry FF is specified, the halt status is released as soon as the basic timer 0 carry FF has been set to 1. The basic timer 0 carry FF corresponds to the BTM0CY flag on a one-to-one basis and is set at fixed time intervals (125 ms). Therefore, the halt status can be released at fixed time intervals. Example To release halt status every 125 ms to execute processing A HLTTMR LOOP: HALT SKT1 BR HLTTMR BTMOCY LOOP ; Specifies setting of basic timer 0 carry FF as halt releasing condition ; Embedded macro ; Branches to LOOP if BTM0CY flag is not set DAT 0010B ; Symbol definition Processing A ; Executes processing A if carry occurs BR LOOP 20.2.6 Releasing halt status by interrupt Releasing the halt status by an interrupt is specified by the "HALT 1000B" instruction. When releasing the halt status by an interrupt is specified, the halt status is released as soon as the interrupt has been accepted. Many interrupt sources are available as described in 12. INTERRUPTS. Which interrupt source is used to release the halt status must be specified in advance in software. To accept an interrupt, each interrupt request must be issued from each interrupt source and each interrupt must be enabled (by setting the corresponding interrupt enable flag). Therefore, the interrupt is not accepted even if the interrupt request is issued, and the halt status is not released. When the halt status is released by accepting an interrupt, the program flow branches to the vector address of the interrupt. When the RETI instruction is executed after interrupt servicing, the program flow is restored to the instruction after the HALT instruction. If all the interrupts are disabled (DI status), the halt status is released by enabling an interrupt (IPxxx = 1) and issuing an interrupt source (IRQxxx = 1), and the flow of the program goes to the instruction after the HALT instruction. 211 PD17933, 17934 Example Releasing halt status by timer 0 and INT pin interrupts In this example, the halt status is released and processing B is executed when timer 0 interrupt is accepted. And processing A is executed when INT pin interrupt is accepted. Each time the halt status has been released, processing C is executed. HLTINT START: DAT 1000B ; Symbol definition ; Address 0000H BR MAIN ;*** Interrupt vector address *** NOP NOP BR INTTM0 INTP: ; ; ; ; ; SIO2 Basic timer 1 Branches to timer 0 interrupt processing Branches to INT pin interrupt processing INT pin interrupt vector address (0004H) Processing A EI RETI INTTM0: Processing B EI RETI MAIN: INITFLG MOV MOV PUT SET2 SET2 LOOP: Processing C EI HALT ;<1> BR LOOP TMOCK1, TM0CK0 DBF1, #0 DBF0, #32H TM0M,DBF TM0RES, TM0EN IPTM0, IP0 ; INT pin interrupt processing ; Timer 0 interrupt processing ; Sets timer 0 count clock to 40 s ; Sets time interval of timer 0 interrupt to 2 ms ; Resets and starts timer 0 ; Enables INT pin and timer 0 interrupts ; Main routine processing ; Enables all interrupts ; Specifies releasing halt status by interrupt HLTINT If the INT pin interrupt request and timer 0 interrupt request are issued simultaneously in the halt status, processing A for the INT pin, which has the higher hardware priority, is executed. After execution of processing A and when "RETI" is executed, the program branches to the "BR LOOP" instruction of <1>. However, the "BR LOOP" instruction is not executed, and timer 0 interrupt is immediately accepted. When the "RETI" instruction is executed after processing B of timer 0 interrupt has been executed, the "BR LOOP" instruction is executed. 212 PD17933, 17934 Caution To reset the interrupt request flag (IRQxxx) once before the halt instruction is executed, insert a NOP instruction (or one or more other instructions) between the HALT instruction and the instruction that resets the interrupt request flag (IRQxxx) as shown below. If a NOP instruction (or one or more other instructions) is not inserted, the interrupt request flag is not reset, and therefore, the halt status is released immediately. Example : : : CLR1 NOP IRQxxx ; Resets IRQxxx flag once ; Resets IRQxxx flag at this timing ; Unless this period is missing, the IRQxxx flag is not reset, ; and the next HALT instruction is immediately released HALT 1000B ; ; IRQxxx is set at certain timing 213 PD17933, 17934 20.2.7 If two or more releasing conditions are specified at same time If two or more halt releasing conditions are specified at same time, the halt status is released when one of the conditions is satisfied. The following program example shows how the releasing conditions are identified if two or more conditions are satisfied at the same time. Example HLTINTP HLTBTM HLTP0D P0D START: BR MAIN ;*** Interrupt vector address *** NOP NOP NOP NOP INTP: Processing A EI RETI BTMOUP: Processing B RET P0DP: Processing C RET MAIN: SET1 EI LOOP: HALT HLTINT OR HLTBTM OR HLTP0C ; Selects interrupt, timer carry FF (125 ms), and P0D input as halt releasing conditions SKF1 BTM0CY ; Detects BTM0CY flag CALL BTM0UP ; Timer carry FF processing if flag is set to 1 SKF P0D, 1111B ; Detects P0D input CALL P0DP ; Port input processing if P0D is high BR LOOP IP0 ; Enables INT pin interrupt ; P0D input processing ; Timer carry FF processing DAT DAT DAT MEM 1000B 0010B 0001B 0.73H ; ; ; ; SI0 Basic timer 1 TM0 INT ; INT pin interrupt vector address (0004H) ; INT pin interrupt processing 214 PD17933, 17934 In the above example, three halt status releasing conditions, INT pin interrupt, 125-ms basic timer 0 carry FF, and port 0D input, are specified. To identify which condition has released the halt status, a vector address (interrupt), BTM0CY flag (timer carry FF), and port register (port input) are detected. To use two or more releasing conditions, the following two points must be noted. * When the halt status is released, all the specified releasing conditions must be detected. * The releasing condition with the higher priority must be detected first. 20.3 Clock Stop Function 20.3.1 Outline of clock stop function The clock stop function stops the oscillation circuit of a 75-kHz crystal resonator by executing the "STOP s" instruction (clock stop status). Therefore, the current consumption of the device is reduced to 10 A MAX (TA = -10 to +50 C, VDD = 1.05 to.1.8 V) 20.3.2 Clock stop status In the clock stop status, all the device operations of the CPU and peripheral hardware units are stopped because the generation circuit of the crystal resonator is stopped. For the operations of the CPU and peripheral hardware units, refer to 20.4 Device Operation in Halt and Clock Stop Status. 20.3.3 Releasing clock stop status Figure 20-3 shows the stop status releasing conditions. The stop status releasing condition is specified by 4-bit data specified by operand "s" of the "STOP s" instruction. The stop status is released when the condition specified by "1" in operand "s" is satisfied. When the stop status has been released, a halt period which is half the time (tSET/2) specified by the basic timer 0 clock selection register as oscillation circuit stabilization wait time has elapsed, and the program execution is started from the instruction next to the "STOP s" instruction. If releasing the stop status by an interrupt is specified, however, the program operation after the stop status has been released differs depending on whether the interrupt is enabled (EI status) or disabled (DI status) when an interrupt source is issued (IRQxxx = 1) with the interrupt enabled (IPxxx = 1). If all the interrupts are enabled (EI status), the stop status is released when the interrupt is enabled (IPxxx = 1) and the interrupt source is issued (IRQxxx = 1), and the program flow returns to the instruction next to the STOP instruction. If all the interrupts are disabled (DI status), the stop status is released when the interrupt is enabled (IPxxx = 1) and the interrupt resource is issued (IRQxxx = 1), and the program flow returns to the instruction next to the STOP instruction. If two or more releasing conditions are specified at one time, and if one of the conditions is satisfied, the stop status is released. If 0000B is specified as stop releasing condition "s", no releasing condition is satisfied. If the device is reset at this time the stop status is released. 215 PD17933, 17934 Figure 20-3. Stop Releasing Conditions STOP s (4 bits) Operand b3 b2 b1 b0 Specifies stop status releasing condition Releases when high level is input to port 0D Undefined (Fix this bit to "0".) Undefined (Fix this bit to "0".) Released by interrupt of INT pin 0 1 Not released even if condition is statisfied Released if condition is satisfied 20.3.4 Releasing clock stop status by high level input of port 0D Figure 20-4 illustrates how the clock stop status is released by the high level input to port 0D. Figure 20-4. Releasing Clock Stop Status By High Level Input of Port 0D 5V VDD 0V H P0D L XOUT Oscillation stops STOP s instruction tSET/2 HALT period Starts from instruction next to STOP s 2.2 V tSET: basic timer 0 setting time 216 PD17933, 17934 20.4 Device Operation in Halt and Clock Stop Status Table 20-1 shows the operations of the CPU and peripheral hardware units in the halt and clock stop status. In the halt status, all the peripheral hardware units continue the normal operation until instruction execution is stopped. In the clock stop status, all the peripheral hardware units stop operation. The control registers that control the operations of the peripheral hardware units operate normally (not initialized) in the halt status, but are initialized to specified values when the clock stop instruction is executed. In other words, all peripheral hardware continues the operation specified by the control register in the halt status, and the operation is determined by the initialized value of the control register in the clock stop status. For the values of the control registers in the clock stop status, refer to 8. REGISTER FILE (RF) AND CONTROL REGISTER. Table 20-1. Device Operation in Halt and Clock Stop Status Peripheral Hardware Halt Program counter System register Peripheral register Control register Timer PLL frequency synthesizer A/D converter Serial interface Stops at address of HALT instruction Retained Retained Retained Normal operation Normal operation Normal operation Stops operation when internal clock (master) is selected and continues operation when external clock (slave) is selected Frequency counter Normal operation Stops operation and used as generalpurpose input port Stops operation and used as generalpurpose I/O port Stops operation Retained Input port Retains output latch Status Clock stop Stops at address of STOP instruction Retained Partly initializedNote Partly initializedNote Operation stops Operation stops Operation stops Stops operation and used as generalpurpose I/O port BEEP output Normal operation LCD controller/driver General-purpose I/O port General-purpose input port General-purpose output port Normal operation Normal operation Normal operation Normal operation Note For the value to which these registers are initialized, refer to 5. SYSTEM REGISTER (SYSREG) and 8. REGISTER FILE (RF) AND CONTROL REGISTER. 20.5 Cautions on Processing of Each Pin in Halt and Clock Stop Status The halt status is used to reduce the current consumption when, say, only the watch is used. The clock stop function is used to reduce the current consumption of the device to only use the data memory. Therefore, the current consumption must be reduced as much as possible in the halt status or clock stop status. At this time, the current consumption significantly varies depending on the status of each pin, and the points shown in Table 20-2 must be noted. 217 PD17933, 17934 Table 20-2. Status of Each Pin in Halt and Clock Stop Status and Cautions (1/2) Pin Function Pin Symbol Status of Each Pin and Cautions on Processing Halt status Generalpurpose I/O port Port 0B P0B3/BEEP P0B2/SO1 P0B1/SI1/SO2 P0B0/SCK Port 1A P1A3 P1A2 P1A1 P1A0 Port 1D P1D3 P1D2 P1D1 P1D0 Port 2B Port 2C Generalpurpose input port Port 0D P2B3-P2B0 P2C3-P2C0 P0D3/AD2 P0D2/AD1 P0D1/AD0 P0D0 Port 1C P1C3/FMIFC/AMIFC P1C2/AMIFC P1C1/TM1 P1C0/TM0 Port 2A P2A2/LCD19 P2A1/LCD18 P2A0/LCD17 Generalpurpose output port Port 0C Port 0A P0A1 P0A0 P0C3-P0C0 (4) Port 1C (P1C3/FMIFC/AMIFC, P1C2/AMIFC, P1C1/TM1, P1C0/TM0) When P1C2/AMIFC or P1C3/FMIFC/ AMIFC pin is used for IF counter, current consumption increases because internal amplifier operates Specified as general-purpose output port. Output contents are retained as is. If pin is externally pulled down while it outputs high level or externally pulled up while it outputs low level, current consumption increases (4) P2A2/LCD19-P2A0/LCD17 Pin used for LCD segment is retained as is. (3) Port 0D (P0D3/AD1-P0D1/AD0, P0D0) Current consumption increases if pin is externally pulled up because it is provided with pull-down resistor selectable by software (3) P0D3/AD2-P0D1/AD0 Pin used for A/D converter is retained as is. Pull-down resistor of P0D3- P0D0 pin retains previous status (2) When specified as input pin Current consumption increases due to noise if pin is floated (2) When specified as general-purpose input port Current consumption does not increase due to noise even if pin is floated (1) When specified as output pin Current consumption increases if pin is externally pulled down while it outputs high level, or externally pulled up while it outputs low level. Exercise care in using N-ch opendrain output (P1A3-P1A0, P1D3P1D0) (1) When specified as general-purpose output port Current consumption increases due to noise if pin is floated Retains status before halt Clock stop status All port pins are set in general-purpose port mode (except P0D3/AD2- P0D1/AD0, P2A2/LCD19-P2A0/LCD17) Input or output mode of general-purpose I/O port set before clock stop status is retained. 218 PD17933, 17934 Table 20-2. Status of Each Pin in Halt and Clock Stop Status and Cautions (2/2) Pin Function Pin Symbol Status of Each Pin and Cautions on Processing Halt status External interrupt PLL frequency synthesizer INT VCOL VCOH EO0 EO1 Clock stop status Current consumption increases due to noise if pin is floated Current consumption increases during PLL operation. When PLL is disabled, pin is in following status: VCOH, VCOL : internally pulled down EO1, EO0 : floated PLL is disabled VCOH, VCOL : internally pulled down Crystal oscillation circuit XIN XOUT EO1, EO0 : floated Current consumption changes due to oscillation waveform of crystal oscillation circuit. The higher oscillation amplitude, the lower current consumption. Oscillation amplitude must be evaluated because it is influenced by crystal resonator or load capacitor used LCD controller/driver LCD19/P2A2 LCD18/P2A1 LCD17/P2A0 LCD16 | LCD0 COM3 | COM0 (2) When LCD controller/driver is used (LCDEN = 1) LCD19-LCD0 : Output segment signals COM3-COM0 : Output common signals (2) When LCD controller/driver is used LCDEN = 0 LCD16-LCD0 : Output low level COM3-COM0 : Output low level (1) When LCD19/P2A2-LCD17/P2A0 are used as general-purpose input port pins When these pins are used as generalpurpose input port pins, the same points as described above must be noted. (1) When LCD19/P2A2-LCD17/P2A0 are used as general-purpose input port pins When these pins are used as generalpurpose input port pins, the same points as described above must be noted. XIN pin is internally pulled down, and XOUT pin outputs high level (3) LCD display off (LCDEN = 0) LCD19-LCD0 : Output segment signals COM3-COM0 : Output common signals 219 PD17933, 17934 21. RESET 21.1 Outline of Reset The reset function is used to initialize the device. The PD17934 can be reset in the following ways: * Reset by RESET pin * WDT&SP reset Figure 21-1. Configuration of Reset Block XOUT Timer FF block XIN Divider Basic timer 0 carry STOP instruction RESET Falling detection circuit Reset control Watchdog timer, stack overflow/underflow detection block WDT&SP reset signal circuit 220 PD17933, 17934 21.2 Reset by RESET Pin When a low level is input to the RESET pin, an internal reset signal is generated. At this point, the program counter, stack, system registers, and control registers are initialized (for the initial value, refer to the description of each register). When the RESET pin is raised next time, the program starts from address 0 at the rising edge of the basic timer 0 carry FF setting signal 125 ms after a high level has been input to the RESET pin. If reset is executed by the RESET pin during program execution, the data in the data memory may be lost. Figure 21-2. Reset Operation by RESET Pin 1.8 V VDD 0V H RESET L H XOUT L BTM0CY flag setting pulse H L Device opeation stops Halt status 125 ms Low-level is input to RESET pin High-level is input to RESET pin Program starts from address 0 221 PD17933, 17934 21.3 WDT&SP Reset WDT&SP reset includes the following: * Watchdog timer reset * Stack pointer overflow/underflow reset Figure 21-3. Outline of WDT&SP Reset WDTCK1 flag WDTCK0 falg Instruction count clock 4096 instruction counter WDTSPRES flag WDT&SP reset signal 8192 instruction counter WDTRES Stack overflow/under flow reset detection circuit SPRSEL0 flag SPRSEL1 flag 21.3.1 Watchdog timer reset The watchdog timer is a circuit that generates a reset signal when the execution sequence of the program is abnormal (hung-up). Hanging-up means that the program jumps to an unexpected routine due to external noise, entering a specific infinite loop and causing the system to be deadlocked. By using the watchdog timer, the program can be restored from this hang-up status because a reset signal is generated from the watchdog timer at fixed time intervals and program execution is started from address 0. The watchdog timer does not function in the clock stop mode and halt mode. Resetting by the watchdog timer initializes all the registers except the stack overflow selection register, watchdog timer counter reset register, and basic timer 0 carry register. The watchdog timer reset is detected by the WDTSPRES flag (R&Reset). 222 PD17933, 17934 21.3.2 Watchdog timer setting flags These flags can be set only once after power-ON reset on power application or reset by the RESET pin. The WDTCK0 and WDTCK1 flags select an interval at which the reset signal is output. The reference time can be selected to the following three conditions: * 4096 instructions * 8192 instructions * Watchdog timer not set On power application, 8192 instructions are selected. If the reset signal generation interval is specified to be 8192 instructions, the watchdog timer FF must be reset at intervals not exceeding 8192 instructions. The valid reset period is from 1 to 8192 instructions. If the reset signal generation interval is 4096 instructions, the watchdog timer FF must be reset at intervals not exceeding 4096 instrutions. The valid reset period is from 1 to 4096 instructions. Figure 21-4. Configuration of Watchdog Timer Clock Selection Register Name Flag symbol b3 b2 b1 b0 Address Read/Write Watchdog timer clock selection 0 0 WW D T C K 1 D T C K 0 (BANK15) 02H R/WNote Selects clock of watchdog timer 0 0 1 1 0 1 0 1 Does not set watchdog timer 4096 instructions Setting prohibited 8192 instructions Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 1 1 Retained Retained Clock stop Note Can be written only once. 223 PD17933, 17934 The WDTRES flag is used to reset the watchdog timer counter. When this flag is set to 1, the watchdog timer counter is automatically reset. If the WDTRES flag is set to 1 once within a reference time in which the WDTCK0 and WDTCK1 flags are set, the reset signal is not output by the watchdog timer. Figure 21-5. Configuration of Watchdog Timer Counter Reset Register Name Flag symbol b3 b2 b1 b0 Address Read/Write Watchdog timer counter reset W0 D T R E S 0 0 (BANK15) 03H W&Reset Fixed to "0" Resets watchdog timer counter 0 1 Invalid Resets watchdog timer counter At reset Reset by RESET pin WDT&SP reset U U U 0 0 0 Clock stop U: Undefined 224 PD17933, 17934 21.3.3 Stack pointer overflow/underflow reset A reset signal is generated if the address or interrupt stack overflows or underflows. Stack pointer overflow/underflow reset can be used to detect a program hang-up in the same manner as watchdog timer reset. The reset signal is generated under the following conditions: * Interrupt due to overflow or underflow of interrupt stack (4 levels) * Interrupt due to overflow or underflow of address stack (15 levels) Reset by stack pointer overflow or underflow initializes all the registers, except the stack overflow selection register, watchdog timer counter reset register, and basic timer 0 carry register. Generation of stack pointer overflow or underflow reset is detected by the WDTSPRES flag (R&Reset). 21.3.4 Stack pointer setting flag The stack overflow/underflow reset selection register can be set only once after reset by the RESET pin. This register specifies whether reset by address stack overflow or underflow and reset by interrupt stack overflow or underflow are enabled or disabled. 225 PD17933, 17934 Figure 21-6. Configuration of Stack Overflow/Underflow Reset Selection Register Name Flag symbol b3 b2 b1 b0 Address Read/Write Stack overflow/underflow reset selection 0 0 S P R S E L 1 S P R S E L 0 (RF) 05H R/WNote Selects address stack overflow/underflow reset 0 1 Disables reset Enables reset Selects interrupt stack overflow/underflow reset 0 1 Disables reset Enables reset Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 1 1 Retained Retained Clock stop Note Can be written only once. 226 PD17933, 17934 Figure 21-7. Configuration of WDT&SP Reset Selection Register Name Flag symbol b3 b2 b1 b0 Address Read/Write WDT&SP reset status detection 0 0 0W D T S P R E S (BANK15) 16H R&Reset Detects occurrence of WDT&SP reset 0 1 No reset request Reset request Fixed to "0" At reset Reset by RESET pin WDT&SP reset 0 0 0 0 1 R Clock stop R: Retained 227 PD17933, 17934 22. INSTRUCTION SET 22.1 Outline of Instruction Set b14-b11 BIN 0000 0001 0010 0011 0100 0101 0110 b15 HEX 0 1 2 3 4 5 6 ADD SUB ADDC SUBC AND XOR OR INC INC RORC MOVT PUSH POP GET PUT PEEK POKE BR CALL RET RETSK RETI EI DI STOP HALT NOP LD SKE MOV SKNE BR BR BR BR r,m r,m r,m r,m r,m r,m r,m AR IX r DBF,@AR AR AR DBF,p p,DBF WR,rf rf,WR @AR @AR ADD SUB ADDC SUBC AND XOR OR m,#n4 m, #n4 m,#n4 m,#n4 m,#n4 m,#n4 m,#n4 0 1 0111 7 s h 1000 1001 1010 1011 1100 1101 1110 1111 8 9 A B C D E F r,m m,#n4 @r,m m,#n4 addr (page 0) addr (page 1) addr (page 2) addr (page 3) ST SKGE MOV SKLT CALL MOV SKT SKF m,r m,#n4 m,@r m,#n4 addr (page 0) m,#n4 m,#n4 m,#n 228 PD17933, 17934 22.2 Legend AR ASR addr BANK CMP CY DBF h INTEF INTR INTSK IX MP MPE m mR mC n n4 PAGE PC P pH pL r rf rfR rfC SP s WR (x) : Address register : Address stack register indicated by stack pointer : Program memory address (low-order 11 bits) : Bank register : Compare flag : Carry flag : Data buffer : Halt release condition : Interrupt enable flag : Register automatically saved to stack when interrupt occurs : Interrupt stack register : Index register : Data memory row address pointer : Memory pointer enable flag : Data memory address indicated by mR, mC : Data memory row address (high-order) : Data memory column address (low-order) : Bit position (4 bits) : Immediate data (4 bits) : Page (bits 12 and 11 of program counter) : Program counter : Peripheral address : Peripheral address (high-order 3 bits) : Peripheral address (low-order 4 bits) : General register column address : Register file address : Register file row address (high-order 3 bits) : Register file column address (low-order 4 bits) : Stack pointer : Stop release condition : Window register : Contents addressed by x 229 PD17933, 17934 22.3 Instruction List Instructions Mnemonic Operand Operation Instruction Code Op code Add ADD r,m m,#n4 ADDC r,m m,#n4 INC AR IX Subtract SUB r,m m,#n4 SUBC r,m m,#n4 Logical operation AND OR r,m m,#n4 r,m m,#n4 XOR r,m m,#n4 Judge SKT SKF Compare SKE SKNE SKGE SKLT Rotate RORC m,#n m,#n m,#n4 m,#n4 m,#n4 m,#n4 r (r) (r) + (m) (m) (m) + n4 (r) (r) + (m) + CY (m) (m) + n4 + CY AR AR + 1 IX IX + 1 (r) (r) - (m) (m) (m) - n4 (r) (r) - (m) - CY (m) (m) - n4 - CY (r) (r) v (m) (m) (m) v n4 (r) (r) (m) (m) (m) n4 (r) (r) v (m) (m) (m) v n4 v CMP 0, if (m) CMP 0, if (m) n = n, then skip n = 0, then skip v v 00000 10000 00010 10010 00111 00111 00001 10001 00011 10011 00110 10110 00100 10100 00101 10101 11110 11111 01001 01011 11001 11011 00111 mR mR mR mR 000 000 mR mR mR mR mR mR mR mR mR mR mR mR mR mR mR mR 000 Operand mC mC mC mC 1001 1000 mC mC mC mC mC mC mC mC mC mC mC mC mC mC mC mC 0111 r n4 r n4 0000 0000 r n4 r n4 r n4 r n4 r n4 n n n4 n4 n4 n4 r (m) - n4, skip if zero (m) - n4, skip if not zero (m) - n4, skip if not borrow (m) - n4, skip if borrow CY (r) b3 (r) b2 (r) b1 (r) b0 (r) (m) (m) (r) if MPE = 1 : (MP, (r)) (m) if MPE = 0 : (BANK, mR, (r)) (m) if MPE = 1 : (m) (MP, (r)) if MPE = 0 : (m) (BANK, mR, (r)) (m) n4 SP SP - 1, ASR PC, PC AR, DBF (PC), PC ASR, SP SP + 1 SP SP - 1, ASR AR AR ASR, SP SP + 1 DBF (p) (p) DBF WR (rf) (rf) WR Transfer LD ST MOV r,m m,r @r,m m, @r m,#n4 MOVT DBF,@AR PUSH POP GET PUT PEEK POKE AR AR DBF,p p,DBF WR,rf rf,WR 230 v 01000 11000 01010 mR mR mR mC mC mC r r r 11010 mR mC r 11101 00111 mR 000 mC 0001 n4 0000 00111 00111 00111 00111 00111 00111 000 000 pH pH rfR rfR 1101 1100 1011 1010 0011 0010 0000 0000 pL pL rfC rfC PD17933, 17934 Instructions Mnemonic Operand Operation Instruction Code Op code Branch BR addr PC10-0 addr, PAGE 0 PC10-0 addr, PAGE 1 PC10-0 addr, PAGE 2 PC10-0 addr, PAGE 3 @AR Subroutine CALL addr PC AR SP SP - 1, ASR PC PC11 0, PC10-0 addr SP SP - 1, ASR PC PC AR PC ASR, SP SP + 1 PC ASR, SP SP + 1 and skip PC ASR, INTR INTSK, SP SP + 1 INTEF 1 INTEF 0 s h STOP HALT No operation 01100 01101 01110 01111 00111 11100 000 0100 addr 0000 Operand addr @AR 00111 000 0101 0000 RET RETSK RETI Interrupt EI DI Others STOP HALT NOP 00111 00111 00111 00111 00111 00111 00111 00111 000 001 010 000 001 010 011 100 1110 1110 1110 1111 1111 1111 1111 1111 0000 0000 0000 0000 0000 s h 0000 231 PD17933, 17934 22.4 Assembler (RA17K) Embedded Macro Instruction Legend flag n : FLG symbol n <> : Bit number : Can be omitted Mnemonic Embedded macro SKTn SKFn SETn CLRn NOTn Operand flag 1, ... flag n flag 1, ... flag n flag 1, ... flag n flag 1, ... flag n flag 1, ... flag n Operation if (flag1) ~ (flag n) = all "1", then skip if (flag 1) ~ (flag n) = all "0", then skip (flag 1) ~ (flag n) 1 (flag 1) ~ (flag n) 0 if (flag n) = "0", then (flag n) 1 if (flag n) = "1", then (flag n) 0 if description = NOT flag n, then (flag n) 0 if description = flag n, then (flag n) 1 (BANK) n Label function-name function-name or expression INITFLGX INITFLG BANKn Expanded instruction BRX CALLX SYSCALX 232 PD17933, 17934 23. RESERVED SYMBOLS 23.1 Data Buffer (DBF) Symbol Name Attribute DBF3 DBF2 DBF1 DBF0 MEM MEM MEM MEM Value 0.0CH 0.0DH 0.0EH 0.0FH R/W R/W R/W R/W R/W Description Bits 15 through 12 of data buffer Bits 11 through 8 of data buffer Bits 7 through 4 of data buffer Bits 3 through 0 of data buffer 23.2 System Registers (SYSREG) Symbol Name Attribute AR3 AR2 AR1 AR0 WR BANK IXH MPH MPE IXM MPL IXL RPH RPL BCD PSW CMP CY Z IXE MEM MEM MEM MEM MEM MEM MEM MEM FLG MEM MEM MEM MEM MEM FLG MEM FLG FLG FLG FLG Value 0.74H 0.75H 0.76H 0.77H 0.78H 0.79H 0.7AH 0.7AH 0.7AH.3 0.7BH 0.7BH 0.7CH 0.7DH 0.7EH 0.7EH.0 0.7FH 0.7FH.3 0.7FH.2 0.7FH.1 0.7FH.0 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Description Bits 15 through 12 of address register Bits 11 through 8 of address register Bits 7 through 4 of address register Bits 3 through 0 of address register Window register Bank register Bits 10 through 8 of index register Bits 6 through 4 of memory pointer Memory pointer enable flag Bits 7 through 4 of index register Bits 3 through 0 of memory pointer Bits 3 through 0 of index register Bits 6 through 3 of general register pointer Bits 2 through 0 of general register pointer BCD operation flag Program status word Compare flag Carry flag Zero flag Index enable flag 233 PD17933, 17934 23.3 LCD Segment Register Symbol Name LCDD19 LCDD18 LCDD17 LCDD16 LCDD15 LCDD14 LCDD13 LCDD12 LCDD11 LCDD10 LCDD9 LCDD8 LCDD7 LCDD6 LCDD5 LCDD4 LCDD3 LCDD2 LCDD1 LCDD0 Attribute MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM Value 14.5CH 14.5DH 14.5EH 14.5FH 14.60H 14.61H 14.62H 14.63H 14.64H 14.65H 14.66H 14.67H 14.68H 14.69H 14.6AH 14.6BH 14.6CH 14.6DH 14.6EH 14.6FH R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register Description 234 PD17933, 17934 23.4 Port Register Symbol Name P0A1 P0A0 P0B3 P0B2 P0B1 P0B0 P0C3 P0C2 P0C1 P0C0 P0D3 P0D2 P0D1 P0D0 P1A3 P1A2 P1A1 P1A0 P1C3 P1C2 P1C1 P1C0 P1D3 P1D2 P1D1 P1D0 P2A2 P2A1 P2A0 P2B3 P2B2 P2B1 P2B0 P2C3 P2C2 P2C1 P2C0 Attribute FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG Value 0.70H.1 0.70H.0 0.71H.3 0.71H.2 0.71H.1 0.71H.0 0.72H.3 0.72H.2 0.72H.1 0.72H.0 0.73H.3 0.73H.2 0.73H.1 0.73H.0 1.70H.3 1.70H.2 1.70H.1 1.70H.0 1.72H.3 1.72H.2 1.72H.1 1.72H.0 1.73H.3 1.73H.2 1.73H.1 1.73H.0 2.70H.2 2.70H.1 2.70H.0 2.71H.3 2.71H.2 2.71H.1 2.71H.0 2.72H.3 2.72H.2 2.72H.1 2.72H.0 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R Note R Note R Note R Note R/W R/W R/W R/W R Note R Note R Note R Note R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Port 0A bit 1 Port 0A bit 0 Port 0B bit 3 Port 0B bit 2 Port 0B bit 1 Port 0B bit 0 Port 0C bit 3 Port 0C bit 2 Port 0C bit 1 Port 0C bit 0 Port 0D bit 3 Port 0D bit 2 Port 0D bit 1 Port 0D bit 0 Port 1A bit 3 Port 1A bit 2 Port 1A bit 1 Port 1A bit 0 Port 1C bit 3 Port 1C bit 2 Port 1C bit 1 Port 1C bit 0 Port 1D bit 3 Port 1D bit 2 Port 1D bit 1 Port 1D bit 0 Port 2A bit 2 Port 2A bit 1 Port 2A bit 0 Port 2B bit 3 Port 2B bit 2 Port 2B bit 1 Port 2B bit 0 Port 2C bit 3 Port 2C bit 2 Port 2C bit 1 Port 2C bit 0 Description Note These ports are input-only ports. The assembler and in-circuit emulator will not output error messages even if an instruction to output from these ports is written. Also, if the instruction is actually executed on a device, the operation will have no change. 235 PD17933, 17934 23.5 Register File (Control Register) Symbol Name SP DBFSP SPRSEL MOVTSEL1 MOVTSEL0 SYSRSP WDTCK WDTRES PLLSCNF PLLMD1 PLLMD0 PLLRFCK3 PLLRFCK2 PLLRFCK1 PLLRFCK0 PLLUL BEEP0SEL BEEP0CK1 BEEP0CK0 WDTCY BTM0CY BTM1CK0 SIO1CK1 SIO1CK0 SIO1MOD SIO1HIZ SIO1TS IEG0 IFCG0STT IFCMD1 IFCMD0 IFCCK1 IFCCK0 IFCSTRT IFCRES Attribute MEM MEM MEM FLG FLG MEM MEM FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG Value 0.81H 0.84H 0.85H 0.87H.1 0.87H.0 0.88H 15.02H 15.03H.3 15.10H.3 15.10H.1 15.10H.0 15.11H.3 15.11H.2 15.11H.1 15.11H.0 15.12H.0 15.14H.2 15.14H.1 15.14H.0 15.16H.0 15.17H.0 15.18H.0 15.1CH.1 15.1CH.0 15.1DH.2 15.1DH.1 15.1DH.0 15.1FH.0 15.21H.0 15.22H.3 15.22H.2 15.22H.1 15.22H.0 15.23H.1 15.23H.0 R/W R/W R R/W R/W R/W R R/W R/W R/W R/W R/W R/W R/W R/W R/W R R/W R/W R/W R R R/W R/W R/W R/W R/W R/W R/W R R/W R/W R/W R/W W R/W Stack pointer DBF stack pointer Stack overflow select flag (Settable only once after power application) MOVT bit select flag MOVT bit select flag System register stack pointer Watchdog timer clock select flag Watchdog timer count reset Swallow counter MSB set flag PLL mode select flag PLL mode select flag PLL reference frequency select flag PLL reference frequency select flag PLL reference frequency select flag PLL reference frequency select flag PLL unlock FF flag BEEP0 enable flag BEEP0 clock select flag BEEP0 clock select flag Watchdog timer/stack pointer reset status detection flag Basic timer 0 carry flag Basic timer 1 clock select flag Serial interface 1 I/O clock select flag Serial interface 1 I/O clock select flag Serial interface 1 SI1/SO2 select flag Serial interface 1 general-purpose port select flag Serial interface 1 transmit/receive start flag INT0 pin interrupt request detection edge direction select flag IF counter gate status detection flag (1: open, 0: close) IF counter mode select flag (10: FMIFC, 11: AMIFC2) IF counter mode select flag (00: FCG, 01: AMIFC) IF counter clock select flag IF counter clock select flag IF counter count start IF counter reset Description 236 PD17933, 17934 Symbol Name ADCCH3 ADCCH2 ADCCH1 ADCCH0 ADCSTRT ADCCMP TM0EN TM0RES TM0CK1 TM0CK0 TM0OVF IPSIO1 IPBTM1 IPTM0 IP0 IRQSIO1 IRQBTM1 IRQTM0 INT0 IRQ0 LCDEN LCD19SEL LCD18SEL LCD17SEL P0DPLD3 P0DPLD2 P0DPLD1 P0DPLD0 P2CBIO3 P2CBIO2 P2CBIO1 P2CBIO0 P2BBIO3 P2BBIO2 P2BBIO1 P2BBIO0 Attribute FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG Value 15.24H.3 15.24H.2 15.24H.1 15.24H.0 15.25H.1 15.25H.0 15.2BH.3 15.2BH.2 15.2BH.1 15.2BH.0 15.2CH.3 15.2FH.3 15.2FH.2 15.2FH.1 15.2FH.0 15.3CH.0 15.3DH.0 15.3EH.0 15.3FH.3 15.3FH.0 15.40H.0 15.69H.2 15.69H.1 15.69H.0 15.6AH.3 15.6AH.2 15.6AH.1 15.6AH.0 15.6BH.3 15.6BH.2 15.6BH.1 15.6BH.0 15.6CH.3 15.6CH.2 15.6CH.1 15.6CH.0 R/W R/W R/W R/W R/W R/W R R/W R/W R/W R/W R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Description A/D converter channel select flag A/D converter channel select flag A/D converter channel select flag A/D converter channel select flag A/D converter compare start flag A/D converter compare result detection flag Modulo timer 0 count start flag Modulo timer 0 reset flag (The value is 0 when read) Modulo timer 0 clock select flag (10: TM10, 11: TM11) Modulo timer 0 clock select flag (00: 75 kHz, 01: 25 kHz) Modulo timer 0 overflow detection flag Serial interface 1 interrupt enable flag Basic timer 1 interrupt enable flag Modulo timer 0 interrupt enable flag INT0 pin interrupt enable flag Serial interface 1 interrupt request detection flag Basic timer 1 interrupt request detection flag Modulo timer 0 interrupt request detection flag INT0 pin status detection flag INT0 pin interrupt request detection flag LCD driver display start flag P2A2/LCD19 switching flag P2A1/LCD18 switching flag P2A0/LCD17 switching flag POD3 pin pull-down resistor switching flag POD2 pin pull-down resistor switching flag POD1 pin pull-down resistor switching flag POD0 pin pull-down resistor switching flag P2C3 I/O select flag P2C2 I/O select flag P2C1 I/O select flag P2C0 I/O select flag P2B3 I/O select flag P2B2 I/O select flag P2B1 I/O select flag P2B0 I/O select flag 237 PD17933, 17934 Symbol Name P1DBIO3 P1DBIO2 P1DBIO1 P1DBIO0 P1ABIO3 P1ABIO2 P1ABIO1 P1ABIO0 P0BBIO3 P0BBIO2 P0BBIO1 P0BBIO0 Attribute FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG FLG Value 15.6DH.3 15.6DH.2 15.6DH.1 15.6DH.0 15.6EH.3 15.6EH.2 15.6EH.1 15.6EH.0 15.6FH.3 15.6FH.2 15.6FH.1 15.6FH.0 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W P1D3 I/O select flag P1D2 I/O select flag P1D1 I/O select flag P1D0 I/O select flag P1A3 I/O select flag P1A2 I/O select flag P1A1 I/O select flag P1A0 I/O select flag P0B3 I/O select flag P0B2 I/O select flag P0B1 I/O select flag P0B0 I/O select flag Description 23.6 Peripheral Hardware Register Symbol Name ADCR SIO1SFR TM0M TM0C AR DBFSTK PLLR IFC Attribute DAT DAT DAT DAT DAT DAT DAT DAT Value 02H 04H 1AH 1BH 40H 41H 42H 43H R/W R/W R/W R/W R R/W R/W R/W R Description A/D converter reference voltage set register Serial interface 1 presettable shift register Timer modulo 0 register Timer modulo 0 counter Address register DBF stack register PLL data register IF counter data register 23.7 Others Symbol Name DBF IX AR_EPA1 AR_EPA0 Attribute DAT DAT DAT DAT Value 0FH 01H 8040H 4040H Description Operand (DBF) for GET/PUT/MOVT/MOVTH/MOVTL instruction Operand (IX) for INC instruction Operand (EPA bit ON) for CALL/BR/MOVT/MOVTH/MOVTL instruction Operand (EPA bit OFF) for CALL/BR/MOVT/MOVTH/MOVTL instruction 238 PD17933, 17934 24. ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings (TA = 25 C) Parameter Supply voltage Symbol VDD0 VDD1 VDD2 Input voltage VI1 VI2 VI3 P0D0-P0D3, P1C0-P1C3 pins VCOH and VCOL pins P0B0-P0B3, P1A0-P1A3, P1D0-P1D3, P2A0-P2A2, P2B0-P2B3, P2C0-P2C3, RESET, and INT pins P0B0-P0B3, P0C0-P0C3, P2B0-P2B3, P2C0-P2C3 EO1 and EO2 pins LCD0-LCD19, COM0-COM3 pins 1 pin Total of P0B0-P0B3, P0C0-P0C3, P2B0-P2B3, and P2C0-P2C3 Low-level output current IOL1 IOL2 1 pin of P0A0, P0A1, and P1D0-P1D3 1 pin other P0A0, P0A1, and P1D0-P1D3 Total of P0A0, P0A1, P0B0-P0B3, P0C0-P0C3, P1A0- P1A3, P1D0-P1D3, P2B0-P2B3, and P2C0-P2C3 Output voltage Operating ambient temperature Storage temperature Tstg -55 to +125 C VBDS TA P0A0, P0A1, P1A0-P1A3, P1D0-P1D3 Condition Rating -0.3 to +2.0 -0.3 to +2.0 -0.3 to +2.0 -0.3 to VDD2+0.3 -0.3 to VDD1+0.3 -0.3 to VDD0+0.3 Unit V V V V V V Output voltage VO1 VO2 VO3 -0.3 to VDD0+0.3 -0.3 to REGLCD1+0.3 -0.3 to REGLCD2+0.3 -3.0 -30.0 V V V mA mA High-level output current IOH 10.0 3.0 45.0 mA mA mA -0.3 to +4.0 -10 to +50 V C Caution If the absolute maximum rating of even one of the above parameters is exceeded even momentarily, the quality of the product may be degraded. The absolute maximum ratings, therefore, specify the value exceeding which the product may be physically damaged. Be sure to use the product with these ratings never being exceeded. 239 PD17933, 17934 Recommended Supply Voltage Range (TA = -10 to +50 C) Parameter Supply voltage Symbol VDD0 VDD1 VDD2 Condition MIN. 1.05 1.05 1.05 TYP. MAX. 1.8 1.8 1.8 Unit V V V Recommended Output Voltage (TA = -10 to +50 C) Parameter Output voltage Symbol VBDS Condition P0A0, P0A1, P1A0-P1A3, P1D0-P1D3 MIN. -0.3 TYP. MAX. +4.0 Unit V 240 PD17933, 17934 DC Characteristics (TA = -10 to +50 C, VDD = VDD0 = VDD1 = VDD2 = 1.05 to 1.8 V) Parameter Supply current Symbol IDD11 IDD12 IDD2 Condition CPU operation (VDD0 = 1.8 V, TA = 25 C) HALT operation (VDD0 = 1.8 V, TA = 25 C) PLL operation (VCOH pin, fIN = 130 MHz, VIN = 0.5 VP-P, VDD = 1.8 V) A/D converter, IF counter operation (fIN = 10.7 MHz, VIN = 0.3 VP-P, VDD2 = 1.8 V) P0B0-P0B3, P1A0-P1A3, P1C0-P1C3, P1D0-P1D3, P2A0-P2A2, P2B0-P2B3, P2C0-P2C3, RESET, INT P0D0-P0D3 P0B0-P0B3, P1A0-P1A3, P1C0-P1C3, P1D0-P1D3, P2A0-P2A2, P2B0-P2B3, P2C0-P2C3, RESET, INT P0D0-P0D3 P0B0-P0B3, P0C0-P0C3, P2B0-P2B3, P2C0-P2C3 EO0, EO1 LCD0-LCD19, COM0-COM3 With P0D0-P0D3 pulled down VIH = VDD0 = 1.1 V VIH = VDD0 Low-level input current IIL1 With XIN pin pulled up VIH = VDD0 = 1.1 V VIH = VDD0 High-level output current IOH1 P0B0-P0B3, P0C0-P0C3, P2B0-P2B3, P2C0-P2C3 (VOH = VDD1 - 0.2 V) EO0, EO1 (VOH = VDD2 - 0.2 V) LCD0-LCD19 (VOH = LCDREG2 - 0.2 V) COM0-COM3 (VOH = LCDREG2 - 0.2 V) P0B0-P0B3, P0C0-P0C3, P2B0-P2B3, P2C0-P2C3 (VOL = 0.2 V) EO0, EO1 (VOL = 0.2 V) P1A0-P1A3 (VOL = 0.2 V) P0A0, P1A1, P1D0-P1D3 (VOL = 0.2 V) LCD0-LCD19 (VOL = 0.2 V) COM0-COM3 (VOL = 0.2 V) LCD0-LCD19 output open, C1-C5 = 0.1 F TA = 25 C P0A0, P0A1, P1A0-P1A3, P1D0-P1D3 (VOH = 1.8 V) EO0, EO1 (VOH = 1.8 V, VOL = 0 V) COM0-COM3 (output open) COM0-COM3 (VOM = VM 0.2 V) VLCD0 -0.2 1 VLCD0 2 2 -2 -2 -0.13 -30 0.8 VDD MIN. TYP. 120 70 7.0 MAX. 320 240 10.0 Unit A A mA IDD3 3.0 7.0 mA High-level input voltage VIH1 VDD V VIH2 Low-level input voltage VIL1 0.8 VDD 0 VDD 0.1 VDD V V VIL2 High-level output voltage VOH1 VOH2 VOH3 High-level input current IIH1 0 0.1 VDD VDD0 REGLCD1 REGLCD2 30 V V V V A A A A mA IOH2 IOH3 IOH4 Low-level output current IOL1 IOL2 IOL3 IOL4 IOL5 IOL6 LCD drive voltage VLCD0 VLCD1 Output off leakage current IL1 IL2 COM intermediate potential output voltage COM intermediate potential output current VM -0.13 -1 -10 0.2 0.2 0.4 6.0 1 10 1.4 2.8 1.5 3.0 1.6 3.2 1 1 VLCD0 +0.2 mA A A mA mA mA mA A A V V A A V IOM A Remark Unless otherwise specified, the characteristics of muxed pins are the same as those of the port pins. 241 PD17933, 17934 AC Characteristics (TA = -10 to +50 C, VDD = VDD0 = VDD1 = VDD2 = 1.05 to 1.8 V) Parameter Operating frequency Symbol fIN1 fIN2 fIN3 fIN4 fIN5 fIN6 SCK input frequency fIN7 Condition VHF mode, sine wave input VIN = 0.3 VP-P HF mode, sine wave input VIN = 0.3 VP-P MF mode, sine wave input VIN = 0.3 VP-P AMIFC pin, sine wave input VIN = 0.3 VP-P AMIFC pin, sine wave input VIN = 0.3 VP-P FMIFC pin, sine wave input VIN = 0.3 VP-P External clock MIN. 35 5 0.8 0.4 0.4 10 TYP. MAX. 220 40 3.5 2 2 11 75 Unit MHz MHz MHz MHz MHz MHz kHz A/D Converter Characteristics (TA = -10 to +50 C, VDD = VDD0 = VDD1 = VDD2 = 1.05 to 1.8 V) Parameter Total conversion error Symbol VDD2 = 1.05 to 1.8 V Condition MIN. TYP. MAX. 3 Unit LSB 242 PD17933, 17934 25. PACKAGE DRAWING 80 PIN PLASTIC TQFP (FINE PITCH) ( 12) A B 60 61 41 40 detail of lead end C D S 80 21 1 20 F G H I M J K P N L NOTE Each lead centerline is located within 0.10 mm (0.004 inch) of its true position (T.P.) at maximum material condition. M ITEM A B C D F G H I J K L M N P Q R S MILLIMETERS 14.00.2 12.00.2 12.00.2 14.00.2 1.25 1.25 0.220.05 0.10 0.5 (T.P.) 1.00.2 0.50.2 0.1450.05 0.10 1.00.05 0.10.05 3 +7 -3 1.2 MAX. Q R INCHES 0.5510.008 0.472 +0.009 -0.008 0.472 +0.009 -0.008 0.5510.008 0.049 0.049 0.009+0.002 -0.003 0.004 0.020 (T.P.) 0.039+0.009 -0.008 0.020+0.008 -0.009 0.006 +0.002 -0.003 0.004 0.040 +0.002 -0.003 0.0040.002 3 +7 -3 0.048 MAX. S80GK-50-9EU 243 PD17933, 17934 26. RECOMMENDED SOLDERING CONDITIONS Solder the PD17933 and PD17934 under the following recommended conditions. For details of the recommended soldering conditions, refer to information document Semiconductor Device Mounting Technology Manual (C10535E). For soldering methods and conditions other than those recommended, consult NEC. Table 26-1. Soldering conditions for surface-mount type PD17933GK-xxx-BE9: 80-pin plastic TQFP (12 mm x 12 mm, 0.5-mm pitch) PD17934GK-xxx-BE9: 80-pin plastic TQFP (12 mm x 12 mm, 0.5-mm pitch) Soldering Method Soldering Conditions Package peak temperature: 235 C; Time: 30 secs. max. (210 C min.); Number of times: twice max.; Number of days: 7Note (after that, prebaking is necessary at 125 C for 10 hours) Infrared reflow VPS VP15-107-2 Partial heating -- Note Number of days in storage after the dry pack has been opened. The storage conditions are at 25 C, 65 % RH max. Caution Do not use two or more soldering methods in combination (except partial heating). 244 PD17933, 17934 APPENDIX A. CAUTIONS ON CONNECTING CRYSTAL RESONATOR When using the system clock oscillation circuit, wire the portion enclosed by the dotted line in the figure below as follows to prevent adverse influence from wiring capacity. * Keep the wiring length as short as possible. * If capacitances C1 and C2 are too high, the oscillation start characteristics may be degraded or current consumption may increase. * Generally, connect a trimmer capacitor for adjusting the oscillation frequency to the XIN pin. Depending on the crystal resonator to be used, however, the oscillation stability differs. Therefore, evaluate the crystal resonator actually used. * The crystal oscillation frequency cannot be accurately adjusted when an emulation probe is connected to the XOUT and XIN pin, because of the capacitance of the probe. Adjust the frequency while measuring the VCO oscillation frequency. PD17933 PD17934 XOUT XIN 75-kHz crystal resonator C1 C2 245 PD17933, 17934 APPENDIX B. DEVELOPMENT TOOLS The following development tools are available for development of programs for the PD17933 and 17934. Hardware Name In-circuit emulator IE-17K IE-17K-ETNote 1 EMU-17KNote 2 Outline IE-17K, IE-17K-ET, and EMU-17K are in-circuit emulators that can be used with any model in the 17K series. IE-17K and IE-17K-ET are connected to a host machine, which is PC-9800 series or IBM PC/ATTM, with RS-232C. EMU-17K is mounted to the expansion slot of a host machine, PC-9800 series. By using these in-circuit emulators with a system evaluation board (SE board) corresponding to each model, these emulators operate dedicated to the model. When man-machine interface software SIMPLEHOSTTM is used, a more sophisticated debugging environment can be created. EMU-17K also has a function to allow you to check the contents of the data memory real-time. SE-17934 is an SE board for the PD17933 and 17934. This board can be used alone to evaluate a system, or in combination with an in-circuit emulator for debugging. EP-17K80GK is an emulation probe for the PD17933 and 17934. By using this probe with TGK080SDPNote 3, the SE board and target system are connected. TGK-080SDP is a conversion socket for 80-pin plastic TQFP (12 x 12 mm). It is used to connect EP17K80GK and target system. SE board (SE-17934) Emulation probe (EP-17K80GK) Conversion socket (TGK-080SDPNote 3) Notes 1. Low-price model: external power supply type 2. This is a product of I.C Corp. For details, consult I.C Corp. (03-3447-3793). 3. A product of TOKYO Eletech Corp. (03-5295-1661). Consult your NEC distributor when purchasing the product. Remark Third party PROM programmers AF-9703, AF-9704, AF-9705, and AF-9706 are available from Ando Electric Co., Ltd. Use these programmers with programmer adapter PA-17P709GC. For details, consult Ando Electric Co., Ltd. (03-3733-1163). 246 PD17933, 17934 Software Name 17K series assembler (RA17K) Outline RA17K is a relocatable assembler that can be commonly used with 17K series. To develop programs for the PD17933 and 17934, this RA17K and a device file (AS17934) are used in combination. The RA17K is provided with linker (LK17K) and document processor (DOC17K) utility. 17K series C-like compiler (emlC-17KTM) Device file (AS17934) Host Machine PC-9800 series OS MS-DOSTM Parts Number S5A13RA17K IBM PC/AT PC DOSTM S7B13RA17K emlC-17K is a C-like compiler that can be used with all models on the 17K series. It is used together with RA17K. AS17934 is a device file for the PD17933 and 17934. It is used together with the assembler common to the 17K series (RA17K). PC-9800 series IBM PC/AT PC-9800 series MS-DOS PC DOS MS-DOS S5A13CC17K S7B13CC17K S5A13AS17707 S7B13AS17707 IBM PC/AT PC DOS SIMPLEHOST is man-machine interface software Support that runs on Windows TM when a program is software (SIMPLEHOST) developed by using an in-circuit emulator and personal computer. PC-9800 series MS-DOS Windows S5A13IE17K PC DOS IBM PC/AT S7B13IE17K Remark The version of the supported OS is as follows: OS MS-DOS PC DOS Windows Version Ver.3.30 to Ver.5.00ANote Ver.3.1 to Ver.5.0Note Ver.3.0 to Ver.3.1 Note MS-DOS Ver. 5.00/5.00A and PC DOS Ver. 5.0 have a task swap function, but this function cannot be used with this software. 247 PD17933, 17934 [MEMO] 248 PD17933, 17934 [MEMO] 249 PD17933, 17934 NOTES FOR CMOS DEVICES 1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it. 2 HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS device behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices. 3 STATUS BEFORE INITIALIZATION OF MOS DEVICES Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function. 250 PD17933, 17934 Regional Information Some information contained in this document may vary from country to country. Before using any NEC product in your application, please contact the NEC office in your country to obtain a list of authorized representatives and distributors. They will verify: * Device availability * Ordering information * Product release schedule * Availability of related technical literature * Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth) * Network requirements In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. NEC Electronics Inc. (U.S.) Santa Clara, California Tel: 408-588-6000 800-366-9782 Fax: 408-588-6130 800-729-9288 NEC Electronics (Germany) GmbH Benelux Office Eindhoven, The Netherlands Tel: 040-2445845 Fax: 040-2444580 NEC Electronics Hong Kong Ltd. Hong Kong Tel: 2886-9318 Fax: 2886-9022/9044 NEC Electronics Hong Kong Ltd. NEC Electronics (France) S.A. Velizy-Villacoublay, France Tel: 01-30-67 58 00 Fax: 01-30-67 58 99 Seoul Branch Seoul, Korea Tel: 02-528-0303 Fax: 02-528-4411 NEC Electronics (Germany) GmbH Duesseldorf, Germany Tel: 0211-65 03 02 Fax: 0211-65 03 490 NEC Electronics (France) S.A. NEC Electronics (UK) Ltd. Milton Keynes, UK Tel: 01908-691-133 Fax: 01908-670-290 Spain Office Madrid, Spain Tel: 01-504-2787 Fax: 01-504-2860 NEC Electronics Singapore Pte. Ltd. United Square, Singapore 1130 Tel: 65-253-8311 Fax: 65-250-3583 NEC Electronics Taiwan Ltd. NEC Electronics Italiana s.r.1. Milano, Italy Tel: 02-66 75 41 Fax: 02-66 75 42 99 NEC Electronics (Germany) GmbH Scandinavia Office Taeby, Sweden Tel: 08-63 80 820 Fax: 08-63 80 388 Taipei, Taiwan Tel: 02-719-2377 Fax: 02-719-5951 NEC do Brasil S.A. Cumbica-Guarulhos-SP, Brasil Tel: 011-6465-6810 Fax: 011-6465-6829 J98. 2 251 PD17933, 17934 emlC-17K and SIMPLEHOST are trademarks of NEC Corporation. MS-DOS and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. PC/AT and PC DOS are trademarks of IBM Corporation. The export of this product from Japan is regulated by the Japanese government. To export this product may be prohibited without governmental license, the need for which must be judged by the customer. The export or re-export of this product from a country other than Japan may also be prohibited without a license from that country. Please call an NEC sales representative. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product. M4 96.5 |
Price & Availability of UPD17933
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |